Federal Aviation Administration March 2009 – Federal Register Recent Federal Regulation Documents

This establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

We are adopting a new airworthiness directive (AD) for certain McDonnell Douglas Model 717-200 airplanes. This AD requires modifying the wire installation of the auxiliary hydraulic pump in the right wheel well of the main landing gear (MLG). This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent a tire burst when the MLG is in the retracted position from causing damage to the wire assembly of the auxiliary hydraulic pump and subsequent electrical arcing, creating the potential of an ignition source to the center wing tank, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA is adopting a new airworthiness directive (AD) for PW models JT9D-7, -7A, -7AH, -7H, -7F, and -7J turbofan engines. This AD requires initial and repetitive borescope inspections of the 2nd stage high-pressure turbine (HPT) rotor and stator assembly. This AD results from an uncontained failure of a 2nd stage HPT rotor disk that caused the engine to separate from the airplane. We are issuing this AD to prevent failure of the 2nd stage HPT rotor disk, which could result in uncontained engine failure, damage to the airplane, and the engine separating from the airplane.

This action will modify Class E airspace at Reno/Tahoe International Airport, Reno, NV. Additional controlled airspace is necessary to accommodate aircraft using the Localizer (LOC) Z Runway 16R approach at Reno/Tahoe International Airport, Reno, NV. This action will enhance the safety and management of aircraft operations at the airport. This action also amends the airport name and makes a minor change to the geographic coordinates of the airport and the VORTAC.

The FAA is issuing this notice to advise the public of a third meeting of RTCA Special Committee 213, Standards for Air Traffic Data Communication Services.

The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 222: Inmarsat Aeronautical Mobile Satellite (Route) Services.

By Federal Register notices (See 73 FR 61447; October 16, 2008 and 73 FR 77102, December 18, 2008) the National Park Service (NPS) and the Federal Aviation Administration (FAA) invited interested persons to apply to fill a vacant position on the National Parks Overflights Advisory Group (NPOAG) Aviation Rulemaking Committee (ARC). This notice invited interested persons to apply to fill the vacancy representing Native American tribal concerns due to the incumbent member's completion of a three-year term appointment on April 2, 2009. This notice informs the public of the person selected to fill the vacancy on the NPOAG ARC.

The FAA is adopting a new airworthiness directive (AD) for Hamilton Sundstrand Propellers model 568F propellers with certain part number (P/N) and serial number (SN) blades. This AD requires removing affected propeller blades from service for rework. This AD results from reports of blades with corrosion pits in the tulip area of the blades. We are issuing this AD to prevent cracks from developing in the tulip area of the blade, which could result in separation of the blade and loss of airplane control.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR 23.562. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA is adopting a new airworthiness directive (AD) for General Electric Company (GE) CF6-80C2 and CF6-80E1 series turbofan engines with high-pressure compressor rotor (HPCR) spool shaft stage 14 disks, part number (P/N) 1703M49G02, 1703M49G03, or 1509M71G10 installed. This AD requires a one-time eddy current inspection (ECI) of the HPCR spool shaft stage 14 disk web for crack indications, and removing from service any parts with web cracks. This AD results from reports of 12 HPCR spool shaft stage 14 disks with web cracks discovered to date. We are issuing this AD to prevent cracks from propagating to an uncontained failure of the disk and damage to the airplane.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA invites public comments about our intention to request the Office of Management and Budget's (OMB) revision of a current information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on November 4, 2008, vol. 73, no. 214, page 65714. The FAA uses the information gathered from Grand Canyon National Park air tour operators to monitor their compliance with the Federal regulations.

The FAA invites public comments about our intention to request the Office of Management and Budget's (OMB) revision of a current information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on October 31, 2008, vol. 73, no. 212, pages 65005. The information is collected from holders of FAA production approvals and selected suppliers to obtain their input on how well the agency is performing the administration and conduct of the Aircraft Certification Systems Evaluation Program (ACSEP).

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 217 meeting: Airport Mapping Databases

This airworthiness directive (AD) supersedes two existing ADs. One AD applies to certain Airbus Model A310-200 and -300 series airplanes. That AD currently requires repetitive inspections for cracking of the flap transmission shafts, and replacement of the transmission shafts if necessary. That AD also provides an optional terminating action for the repetitive inspections. The other existing AD applies to all Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model C4-605R Variant F airplanes (collectively called A300-600 series airplanes); and Model A310-200 and -300 series airplanes. That AD currently requires a one-time inspection of the trimmable horizontal stabilizer actuator (THSA), corrective actions if necessary, and follow-on repetitive tasks. This new AD also requires revising the Airworthiness Limitations Section of the Instructions for Continued Airworthiness to incorporate new limitations and maintenance tasks for aging systems maintenance. This AD results from the manufacturer's determination that life limitations and maintenance tasks are necessary to ensure continued operational safety of the affected airplanes. We are issuing this AD to prevent reduced structural integrity of these airplanes due to the failure of system components.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for certain Boeing Model 757-200, 757-200PF, and 757-300 series airplanes. This AD requires, for certain airplanes, measuring the electrical bond resistance at certain stations and doing any applicable repair; installing support brackets for the hot short protector and new support clamps for the wire bundles; installing the equipment of the hot short protector; and modifying an existing wire bundle and installing a new wire bundle. This AD also requires, for certain other airplanes, measuring the electrical bond resistance at certain stations, measuring the electrical bonding resistance between the hot short protector and rear spar web, and doing any applicable repair. This AD also requires revising the Airworthiness Limitations section of the Instructions for Continued Airworthiness. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent the center fuel tank densitometer from overheating and becoming a potential ignition source inside the fuel tank, which, in combination with flammable fuel vapors, could result in a center fuel tank explosion and consequent loss of the airplane.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for certain Boeing Model 727-100 and 727-200 series airplanes. This AD requires repetitive internal and external high frequency eddy current, mid frequency eddy current, low frequency eddy current, and magneto optic imaging inspections to detect cracks, corrosion, delamination, and materials loss in the lower fastener row of the lower skin and the upper fastener row of the upper skin, and corrective actions if necessary. This AD results from a report of decompression in a Boeing Model 737 airplane at flight level 290. We are issuing this AD to detect and correct scratches and excessive reduction in material thickness from excessive blend-out or corrosion, which could lead to premature cracking in the lap joint. Such cracking could adversely affect the structural integrity of the airplane.

The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 767 airplanes. This AD requires repetitive inspections for cracking of the wing skin, and related investigative/ corrective actions if necessary. This AD results from reports of cracks found in the lower wing skin originating at the forward tension bolt holes of the aft pitch load fitting. We are issuing this AD to detect and correct cracking in the lower wing skin for the forward tension bolt holes at the aft pitch load fitting, which could result in a fuel leak and reduced structural integrity of the airplane.