Airworthiness Directives; Dassault Model Mystere-Falcon 20-C5, 20-D5, 20-E5, and 20-F5 Airplanes, 13147-13148 [E9-6735]

Agencies

• Federal Aviation Administration
• DEPARTMENT OF TRANSPORTATION

[Federal Register Volume 74, Number 57 (Thursday, March 26, 2009)]
[Proposed Rules]
[Pages 13147-13148]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: E9-6735]



[[Page 13147]]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2009-0263; Directorate Identifier 2008-NM-137-AD]
RIN 2120-AA64


Airworthiness Directives; Dassault Model Mystere-Falcon 20-C5, 
20-D5, 20-E5, and 20-F5 Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the 
products listed above. This proposed AD results from mandatory 
continuing airworthiness information (MCAI) originated by an aviation 
authority of another country to identify and correct an unsafe 
condition on an aviation product. The MCAI describes the unsafe 
condition as:

    This Airworthiness Directive (AD) is issued following the 
discovery of hot air leaks when operating the wing anti-icing 
system. The seals Part Number (P/N) MS29513-325, near the de-icing 
valves (12H1) and (12H2) in frame 33 area, do not have the proper 
temperature rating. The consequences, in the area of the hot air 
leak, are risks of ignition of potential hydraulic leaks.
* * * * *
    The proposed AD would require actions that are intended to address 
the unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by April 27, 2009.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New 
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Dassault Falcon Jet, P.O. Box 2000, South Hackensack, New Jersey 07606; 
telephone 201-440-6700; Internet https://www.dassaultfalcon.com. You may 
review copies of the referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington. For information on the availability of this material at the 
FAA, call 425-227-1221 or 425-227-1152.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 
227-1137; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2009-0263; 
Directorate Identifier 2008-NM-137-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
Airworthiness Directive 2008-0123, dated July 2, 2008 (referred to 
after this as ``the MCAI''), to correct an unsafe condition for the 
specified products. The MCAI states:

    This Airworthiness Directive (AD) is issued following the 
discovery of hot air leaks when operating the wing anti-icing 
system. The seals Part Number (P/N) MS29513-325, near the de-icing 
valves (12H1) and (12H2) in frame 33 area, do not have the proper 
temperature rating.
    The consequences, in the area of the hot air leak, are risks of 
ignition of potential hydraulic leaks.
    The purpose of this AD is to verify that seals with correct 
temperature rating have been installed on Mystere-Falcon 20-( )5 
airplanes.

    The corrective action includes replacing the left and right seals 
near de-icing valves (12H1) and (12H2) in frame area 33. You may obtain 
further information by examining the MCAI in the AD docket.

Relevant Service Information

    Dassault has issued Service Bulletin F20-766, dated October 31, 
2005. The actions described in this service information are intended to 
correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have proposed different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
highlighted in a NOTE within the proposed AD.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 187 products of U.S. registry. We also estimate that 
it would take about 1 work-hour per product to comply with the basic 
requirements of

[[Page 13148]]

this proposed AD. The average labor rate is $80 per work-hour. Based on 
these figures, we estimate the cost of the proposed AD on U.S. 
operators to be $14,960, or $80 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

Dassault Aviation (Formerly Avions Marcel Dassault-Breguet Aviation 
(AMD/BA)): Docket No. FAA-2009-0263; Directorate Identifier 2008-NM-
137-AD.

Comments Due Date

    (a) We must receive comments by April 27, 2009.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Mystere-Falcon 20-C5, 20-D5, 20-E5, and 
20-F5 airplanes, certificated in any category, without Dassault 
Service Bulletin F20-766 implemented.

Subject

    (d) Air Transport Association (ATA) of America Code 30: Ice and 
Rain Protection.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:
    This Airworthiness Directive (AD) is issued following the 
discovery of hot air leaks when operating the wing anti-icing 
system. The seals Part Number (P/N) MS29513-325, near the de-icing 
valves (12H1) and (12H2) in frame 33 area, do not have the proper 
temperature rating.
    The consequences, in the area of the hot air leak, are risks of 
ignition of potential hydraulic leaks.
    The purpose of this AD is to verify that seals with correct 
temperature rating have been installed on Mystere-Falcon 20-( )5 
airplanes.
    The corrective action includes replacing the left and right 
seals near de-icing valves (12H1) and (12H2) in frame area 33.

Actions and Compliance

    (f) Unless already done, within 7 months after the effective 
date of this AD, perform an inspection for a red line marking on 
each of the Wiggins couplings that are located near the de-icing 
valves (12H1) and (12H2), in accordance with Dassault Service 
Bulletin F20-766, dated October 31, 2005. If a red line is not 
found, prior to further flight, replace the seals to the left and 
right Wiggins couplings, in accordance with Dassault Service 
Bulletin F20-766, dated October 31, 2005.

FAA AD Differences

    Note 1: This AD differs from the MCAI and/or service information 
as follows: No Differences.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. Send information to ATTN: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone 
(425) 227-1137; fax (425) 227-1149. Before using any approved AMOC 
on any airplane to which the AMOC applies, notify your appropriate 
principal maintenance inspector (PMI) or principal avionics 
inspector (PAI), as appropriate, or lacking a principal inspector, 
your local Flight Standards District Office.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (h) Refer to MCAI EASA Airworthiness Directive 2008-0123, dated 
July 2, 2008; and Dassault Service Bulletin F20-766, dated October 
31, 2005; for related information.

    Issued in Renton, Washington, on March 18, 2009.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
 [FR Doc. E9-6735 Filed 3-25-09; 8:45 am]
BILLING CODE 4910-13-P