Federal Aviation Administration July 2020 – Federal Register Recent Federal Regulation Documents

The FAA is adopting a new airworthiness directive (AD) for certain Aspen Avionics, Inc., Evolution Flight Display (EFD) EFD1000 Emergency Backup Display, EFD1000 Multi-Function Display, and EFD1000 Primary Flight Display systems installed on various airplanes. This AD imposes operating restrictions on these display systems by revising the Limitations section of the airplane flight manual (AFM). This AD was prompted by an automatic reset occurring when the display internal monitor detects a potential fault, causing intermittent loss of airspeed, attitude, and altitude information during flight. The FAA is issuing this AD to address the unsafe condition on these products.

This action amends Class E surface airspace, and Class E airspace extending upward from 700 feet above the surface at Floyd Bennett Memorial Airport, (previously Warren County Airport), Glens Falls, NY due to the decommissioning of the Glens Falls very high frequency omnidirectional range collocated tactical air navigation (VORTAC) system, and cancellation of associated approaches. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations in the area. This action also updates the airport's name.

This action removes Class E airspace area designated as an extension to a Class D surface area for Cecil Airport, Jacksonville, FL, as the Cecil very high frequency omnidirectional range (VOR) has been decommissioned, and the VOR approach cancelled. This action also amends Class D and E airspace by updating the names and geographic coordinates of several airports located in and around Jacksonville, FL, and corrects the line between Cecil Airport and Whitehouse NOLF. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations in the area. This action also makes an editorial change replacing the term Airport/Facility Directory with the term Chart Supplement in the legal descriptions of associated Class D airspace.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus SAS Model A330-200 and A330-300 series airplanes, and all Model A340-200 and A340-300 series airplanes. This proposed AD was prompted by reports of hydraulic system failure due to fatigue failure of the screws attaching the manual valve to the ground service manifold (GSM). This proposed AD would require, for certain GSMs, repetitive replacement of the hydraulic system GSM manual valve attachment screws having certain part numbers; and, for certain other GSMs with certain screws installed, replacement of those screws, as specified in a European Union Aviation Safety Agency (EASA) AD, which will be incorporated by reference. The FAA is proposing this AD to address the unsafe condition on these products.

This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Inc. (Bell) Model 204B, 205A, 205A-1, 205B, 212, 214B, 214B-1, 412, 412CF, and 412EP helicopters. This AD was prompted by a report of a shoulder harness seat belt comfort clip (comfort clip) interfering with the seat belt inertia reel. This AD requires removing comfort clips from service and inspecting the seat belt shoulder harness (harness) for a rip or an abrasion. The actions of this AD are intended to address an unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-941 airplanes. This AD was prompted by a report that seven spoiler servo-controls (SSCs) lost hydraulic locking function due to a sheared seal on the blocking valve. This AD requires repetitive operational tests of the hydraulic locking function on each SSC and replacement if necessary, as specified in a European Union Aviation Safety Agency (EASA), which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is considering a proposal to change 24.813 acres of airport land from aeronautical use to non-aeronautical use and to authorize the sale of airport property located at Indianapolis International Airport, Indianapolis, Indiana. The aforementioned land is not needed for aeronautical use. The land is located east of Ronald Regan Parkway, on the northwest side of the airport. It is currently comprised of an agricultural field, woods, and a small storage building. The proposed future non-aeronautical land use is a life science park that will include buildings, parking and roadways.

The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.A. (Leonardo) Model AB139, AW139, AW169, and AW189 helicopters. This AD was prompted by reports of uncommanded deployment of the emergency flotation system (EFS) due to improper accomplishment of the reset procedure of the shape memory alloy (SMA) inflation system actuation device. This AD requires removal of affected SMA inflation systems and installation of serviceable SMA inflation systems. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Pilatus Aircraft Ltd. (Pilatus) Model PC-24 airplanes. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI identifies the unsafe condition as movement of the aft fuel pipe within the coupling, which can cause damage to the O-rings and lead to a fuel leak, fuel fire or explosion, and consequent loss of control of the airplane. The FAA is proposing this AD to address the unsafe condition on these products.

In accordance with the National Environmental Policy Act of 1969, as amended (NEPA), Council on Environmental Quality NEPA implementing regulations, and FAA Order 1050.1F, Environmental Impacts: Policies and Procedures, the FAA is announcing the availability of the Final Environmental Assessment and Finding of No Significant Impact for SpaceX Falcon Launches at Kennedy Space Center and Cape Canaveral Air Force Station (Final EA and FONSI).

The FAA proposes to adopt a new airworthiness directive (AD) for certain Textron Aviation Inc. (Textron) (type certificate previously held by Beechcraft Corporation) Models F90, 65-90, 65-A90, B90, C90, H90 (T-44A), E90, 65-A90-1 (JU-21A, U-21A, RU-21A, RU-21D, U- 21G, RU-21H), 65-A90-2 (RU-21B), 65-A90-3 (RU-21C), 65-A90-4 (RU-21E, RU-21H), 99, 99A, 99A (FACH), A99, A99A, B99, C99, 100, A100 (U-21F), and B100 airplanes. This proposed AD was prompted by reports of fatigue cracks in the lower forward wing fitting. This proposed AD would require a one-time inspection for the presence of washer part number (P/N) 90-380058-1 on the left-hand (LH) and right-hand (RH) lower forward wing bolt and, if applicable, removing washer P/N 90-380058-1, inspecting the wing fitting, bolt, and nut, replacing the wing fitting if it is cracked, and replacing the washer with washer P/N 90-380019-1. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Gulfstream Aerospace Corporation GVII-G500 airplanes. This proposed AD was prompted by a report of a fuel quantity disparity between the overhead panel touch screens and the touch screen controllers. This proposed AD would require incorporating operating limitations into the airplane flight manual (AFM) until the fuel quantity management system (FQMS) software is updated. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for all Air Tractor, Inc. (Air Tractor) Models AT-250, AT-300, AT-301, AT-302, AT-400, AT-400A, AT-401, AT-401A, AT-401B, AT-402, AT-402A, AT- 402B, AT-501, AT-502, AT-502A, AT-502B, AT-503, AT-503A, AT-504, AT- 602, AT-802, and AT-802A airplanes. This proposed AD was prompted by reports of cracks in the flap torque tube actuator attachment brackets that may cause the flap actuator to detach from the flap torque tube. This proposed AD would require repetitive visual and dye penetrant inspections of the flap actuator attachment bracket welds for cracks and replacement if cracks are identified. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to supersede Airworthiness Directive (AD) 2018-14-02, which applies to certain The Boeing Company Model 777-200, -200LR, -300, and -300ER series airplanes. AD 2018-14-02 requires an inspection for foam insulation on the dripshield above the overhead panel support structure and replacement if necessary. For certain airplanes, AD 2018-14-02 also requires replacement of foam insulation on the overhead panel support structure. Since the FAA issued AD 2018- 14-02, additional areas of Boeing Material Specification (BMS) 8-39 flexible urethane foam were found on the overhead panel support structure. This proposed AD would continue to require the actions in AD 2018-14-02, and, for certain airplanes, this proposed AD would require an inspection of the foam insulation on the overhead panel support structure, and replacement if necessary. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A330-200 series, Model A330-200 Freighter series, Model A330-300 series, Model A330-900 series, Model A340-200 series, Model A340-300 series, Model A340-500 series, Model A340-600 series, Model A380-800 series airplanes; and Model A350-941 and -1041 airplanes. This proposed AD was prompted by a report of a quality issue with a certain repair method of damage-through honeycomb core cargo linings by speed patches applied to both sides. This proposed AD would require a detailed inspection of each affected part and, depending on findings, repair of each affected part, or replacement with a serviceable part, as specified in a European Union Aviation Safety Agency (EASA) AD, which will be incorporated by reference. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA is superseding Airworthiness Directive (AD) 2018-08-02 for all Rolls-Royce Deutschland Ltd & Co KG (RRD) Trent 1000-A2, Trent 1000-AE2, Trent 1000-C2, Trent 1000-CE2, Trent 1000-D2, Trent 1000-E2, Trent 1000-G2, Trent 1000-H2, Trent 1000-J2, Trent 1000-K2, and Trent 1000-L2 model turbofan engines. AD 2018-08-02 required initial and repetitive ultrasonic or visual inspections of the intermediate- pressure compressor (IPC) stage 1 rotor blades, IPC stage 2 rotor blades, and IPC shaft stage 2 dovetail posts, and removal of any cracked parts from service. This AD requires new inspections based on updated inspection thresholds and intervals for these IPC parts. This AD also adds an optional terminating action, amends the asymmetric power condition for engine inspection, and requires an inspection after a cabin depressurization event. This AD was prompted by IPC blade separations resulting in engine failures. Subsequently, the manufacturer identified the need to add new inspections and an optional terminating action, amend the asymmetric power condition for engine inspection, and require an inspection after a cabin depressurization event. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for PZL Swidnik S.A. Model PZL W-3A helicopters. This AD requires repetitively inspecting the main rotor (M/R) vibration absorber star and depending on the inspection outcome, performing more in-depth inspections and repairing, replacing, or removing the vibration absorber star from service. This AD was prompted by a report of corrosion detected on an M/R vibration absorber star. The actions of this AD are intended to address an unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for all GE Aviation Czech s.r.o. M601D-11, M601E-11, M601E-11A, M601E-11AS, M601E-11S, M601F, H80, H80-100, H80-200, H75-100, H75-200, H85-100, and H85-200 model turboprop engines. This AD was prompted by a review by the manufacturer that identified the possibility of a power turbine (PT) rotor overspeed and the uncontained release of PT blades. This AD requires installing a modified engine outlet system. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for certain PZL Swidnik S.A. (PZL) Model W-3A helicopters. This AD requires repetitive inspections of the main transmission (Main XSMN) case for a crack, and depending on the inspection outcome, removing the WR-3 Main XSMN from service before further flight. This AD was prompted by a report of cracks in a Main XSMN case. The actions of this AD are intended to address an unsafe condition on these products.

This action amends, with modifications to reflect changed conditions in Libya and the associated risks to U.S. civil aviation safety, the Special Federal Aviation Regulation (SFAR) prohibiting certain flight operations in the Tripoli Flight Information Region (FIR) (HLLL) by all: United States (U.S.) air carriers; U.S. commercial operators; persons exercising the privileges of an airman certificate issued by the FAA, except when such persons are operating U.S.- registered aircraft for a foreign air carrier; and operators of U.S.- registered civil aircraft, except when the operator of such aircraft is a foreign air carrier. This action incorporates the FAA's prohibition on U.S. civil flight operations in the territory and airspace of Libya at all altitudes contained in Notice to Airmen (NOTAM) KICZ A0026/19, into the SFAR. In addition, the FAA remains concerned about the safety of U.S. civil aviation operations at altitudes below Flight Level (FL) 300 in those portions of the Tripoli FIR (HLLL) that are outside the territory and airspace of Libya because of the hazards described in the preamble to the FAA's March 2019 final rule. Accordingly, this final rule also prohibits U.S. civil flight operations below FL300 in those portions of the Tripoli FIR (HLLL) outside the territory and airspace of Libya. This action also extends the expiration date of the SFAR from March 20, 2021, to March 20, 2023. Finally, the FAA republishes the approval process and exemption information for this SFAR, consistent with other recently published flight prohibition SFARs, and makes minor administrative revisions.

The FAA proposes to adopt a new airworthiness directive (AD) for certain CFM International, S.A. (CFM) LEAP-1A23, LEAP-1A24, LEAP- 1A24E1, LEAP-1A26, LEAP-1A26CJ, LEAP-1A26E1, LEAP-1A29, LEAP-1A29CJ, LEAP-1A30, LEAP-1A32, LEAP-1A33, LEAP-1A33B2, LEAP-1A35A model turbofan engines. This proposed AD was prompted by an investigation by CFM that showed a subsurface anomaly in a part manufactured using the same material as the LEAP-1A high-pressure turbine (HPT) stage 2 disk. This proposed AD would require an ultrasonic inspection (UI) of the HPT stage 2 disk and replacement of any HPT stage 2 disk that fails the UI with a part eligible for installation. The FAA is proposing this AD to address the unsafe condition on these products.

This action modifies Class D airspace at the Mountain Home Air Force Base Airport. This action also modifies Class E airspace, designated as a surface area. Additionally, this action modifies Class E airspace, extending upward from 700 feet above the surface. This action also modifies Class E airspace, extending upward from 1,200 feet above the surface. Further, this action removes Mountain Home Municipal Airport from the legal description of the Class E airspace extending upward from 700 feet or more above the surface. Lastly, this action implements two administrative amendments to the airspace legal descriptions.

This action amends the Class D airspace and Class E surface airspace at Wright-Patterson AFB, Dayton, OH, and Wilmington Air Park, Wilmington, OH; revokes the Class E airspace designated as an extension to Class D and Class E surface area at Wilmington Air Park; amends the Class E airspace extending upward from 700 feet above the surface at multiple Ohio airports; and establishes Class E airspace extending upward from 700 feet above the surface at Springfield-Beckley Municipal Airport, Springfield, OH. This action is the result of airspace reviews caused by the decommissioning of the Springfield VHF omnidirectional range (VOR) navigation aid as part of the VOR Minimum Operational Network (MON) Program, and the decommissioning of the Springfield localizer and glideslope at Springfield-Beckley Municipal Airport. The names and geographic coordinates of multiple Ohio airports are also being updated to coincide with the FAA's aeronautical database.

This action modifies Class E airspace, designated as a surface area, at Ralph Wein Memorial Airport. This action also modifies the Class E airspace extending upward from 700 feet above the surface. Additionally, this action modifies the Class E airspace extending upward from 1,200 feet above the surface. Further, this action removes the Kotzebue VOR/DME from the airspace legal descriptions. Lastly, this action implements several administrative corrections to the airspace legal descriptions.