Department of Transportation August 2018 – Federal Register Recent Federal Regulation Documents

In compliance with the Paperwork Reduction Act of 1995, the U.S. Department of Transportation invites the general public, industry and other governmental parties to comment on the information collection request (ICR) OMB No. 2105-0009 Committee Candidate Biographical Information Request Form. The information collection request previously approved by the Office of Management and Budget (OMB) expired on May 31, 2012. The collection is needed to facilitate background investigations of individuals seeking or currently appointed to a Department committee. A Federal Register Notice with a 60-day comment period soliciting comments on the following information collection was published June 11, 2018, and the comment period ended August 10, 2018.

These special conditions are issued for Ultramagic S.A. Models M-56, M-56C, M-65, M-65C, M-77, M-77C, M-90, M-105, M-120, M-130, M- 145, M-160, N-180, N-210, N-250, N-300, N-355, N-425, S-70, S-90, S- 105, S-130, S-160, T-150, T-180, T-210, V-56, V-65, V-77, V-90, and V- 105 balloons. These balloons will have novel or unusual design features associated with a standard construction basket with a singular distribution that includes four occupant seats and a lower sidewall. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for these design features. These special conditions contain the additional safety standards the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The revision of this collection involves the logging of training time in aviation training devices under the provisions of regulations specified in the background of this document, and the logging of flight time as a second in command (SIC) under the provisions of regulations specified in the background of this document.

We propose to supersede Airworthiness Directive (AD) 2016-07- 23, which applies to all Airbus SAS Model A318, A319, A320, and A321 series airplanes. AD 2016-07-23 requires, for certain airplanes, repetitive replacements of the fixed fairing upper and lower attachment studs of both the left-hand (LH) and right-hand (RH) main landing gear (MLG); and repetitive inspections for corrosion, wear, fatigue cracking, and loose studs of each forward stud assembly of the fixed fairing door upper and lower forward attachments of both the LH and RH MLG; and replacement if necessary. AD 2016-07-23 also provides an optional terminating modification for the repetitive replacements of the fixed fairing upper and lower attachment studs. Since we issued AD 2016-07-23, we have determined that for some airplane configurations, associated fixed fairing assembly part numbers susceptible to fatigue cracking were not listed in certain service information required by AD 2016-07-23. In addition, we have determined that additional work is necessary to re-identify the fixed fairing assembly part number on certain airplanes. This proposed AD would retain the requirements of AD 2016-07-23 and, for certain airplanes, require re-identification of the LH and RH fixed fairing assemblies' part numbers. We are proposing this AD to address the unsafe condition on these products.

We propose to adopt a new airworthiness directive (AD) for all Airbus SAS Model A330-200 Freighter series airplanes, Model A330-200 and -300 series airplanes, and Model A340-200 and -300 series airplanes. This proposed AD was prompted by defects found during production tests of ram air turbine (RAT) units; investigation revealed that the defects were due to certain RAT hydraulic pumps having an alternative manufacturing process of the pump pistons. This proposed AD would require replacing any defective RAT hydraulic pump with a serviceable part and re-identifying the RAT module part number. We are proposing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for certain ATR-GIE Avions de Transport R[eacute]gional Model ATR42-200, -300, and -320 airplanes. This AD was prompted by a determination that more restrictive maintenance instructions and airworthiness limitations are necessary. This AD requires updating the maintenance or inspection program, as applicable, to incorporate new or more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.

Under the Paperwork Reduction Act of 1995 (PRA), this notice announces that FRA is forwarding the Information Collection Request (ICR) abstracted below to the Office of Management and Budget (OMB) for review and comment. The ICR describes the information collections and their expected burden. On July 2, 2018, FRA published a notice providing a 60-day period for public comment on the ICR.

PHMSA published a notice in the Federal Register to seek public comments on a report developed to support improvements in gas and hazardous liquid pipeline risk models titled ``Pipeline Risk ModelingOverview of Methods and Tools for Improved Implementation'' (Pipeline Risk Modeling Report). PHMSA has received a request to extend the comment period to allow stakeholders more time to evaluate the notice. PHMSA has concurred with this request and has extended the comment period for an additional 30 days.

This action proposes to amend Class E airspace extending upward from 700 feet above the surface at Jacksonville Municipal Airport, Jacksonville, IL. The FAA is proposing this action as the result of an airspace review caused by the decommissioning of the Jacksonville VHF omnidirectional range (VOR) navigation aid, which provided navigation information for the instrument procedures at this airport, as part of the VOR Minimum Operational Network (MON) Program. The geographic coordinates for the airport would also be updated to coincide with the FAA's aeronautic database. This action is necessary for the safety and management of instrument flight rules (IFR) operations at this airport.

This action proposes to modify Class E airspace extending upward from 700 feet above the surface at Lac Qui Parle County Airport (formerly Madison-Lac Qui Parle Airport), Madison, MN, to accommodate new standard instrument approach procedures for instrument flight rules (IFR) operations at this airport due to the decommissioning of the Madison non-directional radio beacon (NDB) and cancellation of the associated approach.. This action would enhance the safety and management of IFR operations at this airport. An editorial change also would be made to the airspace designation removing the city from the airport name.

We are adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by a report of protective caps that were not removed from fire extinguishing lines in certain areas of the engines. This AD requires an inspection for the presence of protective caps on fire extinguishing lines, and corrective action. We are issuing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for certain Airbus SAS Model A319-115 and -132 airplanes, and Model A320-214, -216, -232, and -233 airplanes. This AD was prompted by a report indicating that certain modified airplanes do not have electrical ground wires on the fuel level sensing control unit (FLSCU), which adversely affects the fuel gravity feeding operation. This AD requires modification of the FLSCU wiring. We are issuing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This AD was prompted by a report indicating that during a fleet survey on a retired Model 737 airplane, cracking was found common to the number 3 windshield assembly, aft sill web. This AD requires, at certain locations, repetitive high frequency eddy current (HFEC) inspections of the number 3 windshield assembly, aft sill web; and applicable on-condition actions. We are issuing this AD to address the unsafe condition on these products.

In accordance with the Paperwork Reduction Act of 1995 (PRA), this notice announces that the request to renew the previously approved information collection request (ICR) OMB No. 2105-0552, ``Reports by Air Carriers on Incidents Involving Animals During Air Transport,'' has been forwarded to the Office of Management and Budget (OMB). The current ICR approved by OMB expires August 31, 2018. DOT published a Federal Register notice with a 60-day comment period soliciting comments on the collection of information on May 21, 2018.

The FHWA is issuing this notice to advise the public that the 2004 Notice of Intent (NOI) published in the Federal Register for Federal-aid project HPP-1602(539), the I-759 Extension, in Etowah County, Alabama is being rescinded. An environmental impact statement (EIS) will not be prepared for this project.

This action amends Class D airspace at San Marcos Regional Airport, Austin, TX; establishes Class E airspace designated as a surface area at Georgetown Municipal Airport, Georgetown, TX, and San Marcos Regional Airport; and amends Class E airspace extending upward from 700 feet above the surface at San Marco Regional Airport and Lockhart Municipal Airport, Lockhart, TX. This action is at the request of Austin Air Traffic Control Tower (ATCT)/Terminal Radar Approach Control (TRACON) to establish part-time Class E airspace designated as a surface area at Georgetown Municipal Airport and San Marcos Regional Airport and to review the associated airspace for the safety and management of instrument flight rule (IFR) operations at these airports. The name of San Marcos Regional Airport is updated to coincide with the FAA's aeronautical database, and the outdated term ``Airport/Facility Directory'' is replaced with the term ``Chart Supplement''.

This rule is part of FRA's broader initiative to reduce the paperwork burden of its regulations while still supporting compliance with the Federal hours of service laws and regulations. Current regulations require employees covered by those laws or regulations (covered service employees) to create and retain hours of service records by hand (a paper system) or ``certify'' the record using a compliant computerized system (an electronic system) with program logic. Cognizant of the burden placed on small operations, FRA provides a simplified method of computerized recordkeeping (an automated system)in which employees apply their electronic signatures to automated records stored in a railroad computer system without the complexity and functionality of an electronic systemfor eligible smaller railroads (and contractors and subcontractors providing covered service employees to such railroads). This rule does not require the use of automated recordkeeping, but, when implemented by the small operations for which it is tailored, it will decrease the burden hours spent on hours of service recordkeeping.

The FHWA is issuing this notice to advise the public that the 1996 Record of Decision (ROD) and the Final Environmental Impact Statement (FEIS) for projects M-8508(1) and ST-697-7, the Huntsville Southern Bypass and Weatherly Road Extension, in Madison County, Alabama is rescinded.

The FAA proposes to rule and invites public comment on the release of land at the Nome Airport, Nome, Alaska.

We are adopting a new airworthiness directive (AD) for certain GE Aviation Czech H80-200 turboprop engines. This AD requires replacing the beta switch and adjusting the engine push-pull control to prevent the propeller governor control from going to a negative thrust position. This AD was prompted by an accident involving an Aircraft Industries (AI) L 410 UVP-E20 airplane caused by one propeller going to a negative thrust position during the landing approach. We are issuing this AD to address the unsafe condition on these products.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on June 28, 2018. The required information to be collected will be used to determine if licensees or those who have permits have complied with financial responsibility requirements for maximum probable loss determination (MPL) analysis as set forth in FAA regulations. The FAA is responsible for determining MPL required to covered claims by a third party for bodily injury or property damage, and the United States, its agencies, and its contractors and subcontractors for covered property damage or loss, resulting from a Commercial space transportation permitted or licensed activity. The MPL determination forms the basis for financial responsibility requirements issued in a license or permit order.

This action amends Title 14 Code of Federal Regulations (14 CFR) part 71 relating to airspace designations to reflect the approval by the Director of the Federal Register of the incorporation by reference of FAA Order 7400.11C, Airspace Designations and Reporting Points. This action also explains the procedures the FAA will use to amend the listings of Class A, B, C, D, and E airspace areas; air traffic service routes; and reporting points incorporated by reference.

We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model DHC-8-400 series airplanes. This AD was prompted by reports of arcing and smoke emanating from the windshields. This AD requires a revision to the maintenance or inspection program, as applicable, to include an inspection of the windshield moisture seal for signs of cracks, erosion, wear, and other deterioration; doing that inspection and repair if necessary; and re-torqueing the screws that fasten the windshield heater terminal lugs and applying sealant to the screw heads of the windshield heaters. We are issuing this AD to address the unsafe condition on these products.