Department of Transportation June 2016 – Federal Register Recent Federal Regulation Documents

Airworthiness Directives; General Electric Company Turbofan Engines
Document Number: C1-2016-14474
Type: Rule
Date: 2016-06-30
Agency: Federal Aviation Administration, Department of Transportation
Civil Penalties
Document Number: 2016-15566
Type: Rule
Date: 2016-06-30
Agency: Maritime Administration, Department of Transportation
This interim final rule updates the maximum civil penalty amounts for violations of statutes and regulations administered by MARAD pursuant to the Federal Civil Penalties Inflation Adjustment Act Improvement Act of 2015. This interim final rule amends our regulations to reflect the new, adjusted civil penalty amounts MARAD may assess pursuant for violations of procedures related to the American Fisheries Act, certain regulated transactions involving documented vessels, the Automated Mutual Assistance Vessel Rescue program (AMVER), and the Defense Production Act.
Indexing the Annual Operating Revenues of Railroads
Document Number: 2016-15546
Type: Notice
Date: 2016-06-30
Agency: Surface Transportation Board, Department of Transportation
Pipeline Safety: Inflation Adjustment of Maximum Civil Penalties
Document Number: 2016-15529
Type: Rule
Date: 2016-06-30
Agency: Pipeline and Hazardous Materials Safety Administration, Department of Transportation
PHMSA is revising references in its regulations to the maximum civil penalties for violations of the Federal Pipeline Safety Laws, or any PHMSA regulation or order issued thereunder. Under the ``Federal Civil Penalties Inflation Adjustment Act Improvements Act of 2015,'' which further amended the ``Federal Civil Penalties Inflation Adjustment Act of 1990,'' federal agencies are required to adjust their civil monetary penalties effective August 1, 2016, and then annually thereafter, to account for changes in inflation. PHMSA finds good cause to amend the regulation related to civil penalties without notice and opportunity for public comment. For the reasons described below, advance public notice is unnecessary.
Small Entity Size Standards Under the Regulatory Flexibility Act
Document Number: 2016-15437
Type: Rule
Date: 2016-06-30
Agency: Surface Transportation Board, Department of Transportation
On July 11, 2013, the Board issued a notice of proposed size standards for purposes of the Regulatory Flexibility Act, along with a request for public comment. This decision discusses the comment received in response to the proposed size standards and adopts the proposed standard as the final statement of agency policy concerning the definition of ``small business.''
Request for Information: Nationally Uniform 911 Data System
Document Number: 2016-15368
Type: Notice
Date: 2016-06-30
Agency: National Highway Traffic Safety Administration, Department of Transportation
The development of a nationally uniform 911 data system, containing uniform data elements for all Computer Aided Dispatch (CAD) data, data associated with the operation of local and State 911 systems, and Extensible Markup Language (XML) schema (or technical equivalent) that would enable the collection, analysis and sharing of standardized administrative data, operational data, cost data and all Computer Aided Dispatch (CAD) data received, collected, processed, and transmitted during 911 calls; that would be developed and made available to all 911 Public Safety Answering Points (PSAPs) and 911 Authorities at the state and local levels. This nationally uniform 911 data system, once developed, would provide essential information to assist strategic planning, governance decisions, and improvements to the 911 system and its operation at all levels of government. These data would also be useful to private sector companies providing support services to local and state 911 agencies.
Hazardous Materials: Miscellaneous Petitions for Rulemaking (RRR)
Document Number: 2016-15303
Type: Proposed Rule
Date: 2016-06-30
Agency: Pipeline and Hazardous Materials Safety Administration, Department of Transportation
In response to petitions for rulemaking submitted by the regulated community, PHMSA proposes to amend the Hazardous Materials Regulations (HMR; 49 CFR parts 171 through 180) to update, clarify, or provide relief from miscellaneous regulatory requirements. Specifically, PHMSA is proposing amendments that include, but are not limited to, the following: Incorporating by Reference (IBR) multiple publications from both the Compressed Gas Association (CGA) and the Chlorine Institute; addressing inconsistencies with domestic and international labels and placards; permitting alternative testing for aerosols; no longer mandating that excepted quantities comply with the emergency response telephone requirement; allowing electronic signatures for Environmental Protection Agency (EPA) manifest forms; and no longer requiring the service pressure to be marked on Department of Transportation (DOT) 8 and 8L cylinders.
National Advisory Committee on Travel and Tourism Infrastructure; Solicitation for Committee Member Nominations
Document Number: 2016-15285
Type: Notice
Date: 2016-06-30
Agency: Department of Transportation, Office of the Secretary
The Department of Transportation seeks member nomination for our National Advisory Committee on Travel and Tourism Infrastructure (NACTTI).
Environmental Impact Statement for the California High Speed Rail System San Francisco to San Jose Section, CA
Document Number: 2016-15409
Type: Notice
Date: 2016-06-29
Agency: Federal Railroad Administration, Department of Transportation
On May 9, 2016, FRA published a NOI announcing its intent to jointly prepare an Environmental Impact Report (EIR) and Environmental Impact Statement (EIS) with the California High-Speed Rail Authority (Authority) for the San Francisco to San Jose Section of the California High-Speed Rail (HSR) System, Blended System Project (Blended System Project or Project) and requesting public comments. Through this notice, FRA is extending the comment period and inviting the public and all interested parties to provide comments on the scope of the EIR/EIS, including the proposed purpose and need, the alternatives to consider, potential environmental impacts of concern, and methodologies for analysis of impacts.
Hazardous Materials: Revision of Maximum and Minimum Civil Penalties
Document Number: 2016-15404
Type: Rule
Date: 2016-06-29
Agency: Pipeline and Hazardous Materials Safety Administration, Department of Transportation
PHMSA is revising the maximum and minimum civil penalties for a knowing violation of the Federal hazardous material transportation law or a regulation, order, special permit, or approval issued under that law. The ``Federal Civil Penalties Inflation Adjustment Act Improvements Act of 2015'' (the 2015 Act), which amended the Federal Civil Penalties, Inflation Adjustment Act of 1990 (the Inflation Adjustment Act), requires Agencies to update their civil monetary penalties through interim final rulemaking. The maximum civil penalty for a knowing violation is now $77,114, except for violations that result in death, serious illness, or severe injury to any person or substantial destruction of property, for which the maximum civil penalty is $179,933. In addition, the minimum civil penalty amount for a violation relating to training is now $463.
Reports, Forms, and Record Keeping Requirements Agency Information Collection Activity Under OMB Review
Document Number: 2016-15366
Type: Notice
Date: 2016-06-29
Agency: National Highway Traffic Safety Administration, Department of Transportation
In compliance with the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.), this notice announces that the Information Collection Request (ICR) abstracted below has been forwarded to the Office of Management and Budget (OMB) for review and comment. The ICR describes the nature of the information collection and the expected burden. The Federal Register Notice with a 60-day comment period was published on December 9, 2015 (Federal Register/Vol. 80, No. 236/pp. 16613-16615).
Bridgestone Americas Tire Operations, LLC, Receipt of Petition for Decision of Inconsequential Noncompliance
Document Number: 2016-15316
Type: Notice
Date: 2016-06-29
Agency: National Highway Traffic Safety Administration, Department of Transportation
Bridgestone Americas Tire Operations, LLC (BATO), has determined that certain Bridgestone VSB heavy-duty radial truck tires do not fully comply with paragraph S6.5(d) of Federal Motor Vehicle Safety Standard (FMVSS) No. 119, New Pneumatic Tires for Motor Vehicles with a GVWR of more than 4,536 Kilograms (10,000 pounds) and Motorcycles. BATO filed a report dated April 7, 2016, pursuant to 49 CFR part 573, Defect and Noncompliance Responsibility and Reports. BATO then petitioned NHTSA under 49 CFR part 556 for a decision that the subject noncompliance is inconsequential as it relates to motor vehicle safety.
Commercial Driver's License Standards: Missouri Department of Revenue (DOR); Application for Exemption
Document Number: 2016-15287
Type: Notice
Date: 2016-06-29
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA announces its decision to grant the Missouri DOR and all other State driver licensing agencies (SDLAs) a limited exemption from the Agency's commercial driver's license (CDL) regulations. These regulations allow a State to waive the CDL skills test for applicants regularly employed or previously employed within the last 90 days in a military position requiring operation of a commercial motor vehicle (CMV). The exemption extends the 90-day timeline to one year following the driver's separation from military service. The Missouri DOR believed that the 90-day timeframe is too short to take advantage of the waiver for many of the qualified discharged veterans entering and settling into civilian life. A similar exemption was granted to the Commonwealth of Virginia, Department of Motor Vehicles (VA DMV) and all SDLAs on July 8, 2014, effective through July 8, 2016. FMCSA has analyzed the Missouri DOR exemption application and the public comments and has determined that the exemption will achieve a level of safety that is equivalent to, or greater than, the level that would be achieved absent such exemption.
Proposed Amendment of Class E Airspace, Salem, OR
Document Number: 2016-15266
Type: Proposed Rule
Date: 2016-06-29
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to modify Class E airspace extending upward from 700 feet above the surface at McNary Field, Salem, OR. Two approaches, the Localizer (LOC) Y runway (RWY) 31 and the LOC/Distance Measuring Equipment (DME) Back Course (BC) approach RWY 13 were identified as needing additional airspace to meet airspace requirements. The FAA, also, found modification of the airspace for the LOC/DME BC RWY 13 posed an increased risk to the safety of Instrument Flight Rules (IFR) operations for Standard Instrument Approach Procedures (SIAPs) at the airport.
Extension of a Previously Approved Collection: Public Charters, 14 CFR Part 380
Document Number: 2016-15286
Type: Notice
Date: 2016-06-28
Agency: Department of Transportation, Office of the Secretary
In compliance with the Paperwork Reduction Act of 1995, Public Law 104-13, the Department of Transportation (DOT) invites the general public, industry and other governmental parties to comment on Public Charters, 14 CFR part 380. A Federal Register Notice with a 60-day comment period soliciting comments on the following information collection was published on March 24, 2016 (81 FR 15787). No comments were received.
Qualification of Drivers; Exemption Applications; Diabetes Mellitus
Document Number: 2016-15223
Type: Notice
Date: 2016-06-28
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA announces receipt of applications from 57 individuals for exemption from the prohibition against persons with insulin-treated diabetes mellitus (ITDM) operating commercial motor vehicles (CMVs) in interstate commerce. If granted, the exemptions would enable these individuals with ITDM to operate CMVs in interstate commerce.
Qualification of Drivers; Exemption Applications; Diabetes
Document Number: 2016-15222
Type: Notice
Date: 2016-06-28
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA announces its decision to renew the exemptions from its rule prohibiting persons with insulin-treated diabetes mellitus (ITDM) from operating commercial motor vehicles (CMVs) in interstate commerce for 90 individuals. FMCSA has statutory authority to exempt individuals from this rule if the exemptions granted will not compromise safety. The Agency has concluded that granting these exemption renewals will provide a level of safety that is equivalent to or greater than the level of safety maintained without the exemptions for these CMV drivers.
Qualification of Drivers; Exemption Applications; Vision
Document Number: 2016-15221
Type: Notice
Date: 2016-06-28
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA announces receipt of applications from 23 individuals for exemption from the vision requirement in the Federal Motor Carrier Safety Regulations. They are unable to meet the vision requirement in one eye for various reasons. The exemptions will enable these individuals to operate commercial motor vehicles (CMVs) in interstate commerce without meeting the prescribed vision requirement in one eye. If granted, the exemptions would enable these individuals to qualify as drivers of commercial motor vehicles (CMVs) in interstate commerce.
Qualification of Drivers; Exemption Applications; Diabetes Mellitus
Document Number: 2016-15220
Type: Notice
Date: 2016-06-28
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA announces receipt of applications from 58 individuals for exemption from the prohibition against persons with insulin-treated diabetes mellitus (ITDM) operating commercial motor vehicles (CMVs) in interstate commerce. If granted, the exemptions would enable these individuals with ITDM to operate CMVs in interstate commerce.
Qualification of Drivers; Exemption Applications; Diabetes Mellitus
Document Number: 2016-15219
Type: Notice
Date: 2016-06-28
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA confirms its decision to exempt 74 individuals from its rule prohibiting persons with insulin-treated diabetes mellitus (ITDM) from operating commercial motor vehicles (CMVs) in interstate commerce. The exemptions enable these individuals to operate CMVs in interstate commerce.
Proposed Amendment of Class E Airspace; Tekamah, NE
Document Number: 2016-15186
Type: Proposed Rule
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to modify Class E airspace extending upward from 700 feet above the surface at Tekamah Municipal Airport, Tekamah, NE. Controlled airspace is necessary to accommodate standard instrument approach procedures (SIAP) at Tekamah Municipal Airport for the safety and management of Instrument Flight Rules (IFR) operations at airport.
Proposed Revocation of Class E Airspace; Farmington, MO; and Amendment of Class E Airspace for the following Missouri Towns; Ava, MO; Cameron, MO; Chillicothe, MO; Farmington, MO; and Festus, MO
Document Number: 2016-15185
Type: Proposed Rule
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to remove Class E surface area airspace at Farmington Regional Airport, Farmington, MO; and modify Class E airspace extending upward from 700 feet above the surface at Bill Martin Memorial Airport, Ava, MO; Cameron Memorial Airport, Cameron, MO; Chillicothe Municipal Airport, Chillicothe, MO; Farmington Regional Airport, Farmington, MO; and Festus Memorial Airport, Festus, MO. Decommissioning of non-directional radio beacons (NDBs), cancellation of NDB approaches, and implementation of area navigation (RNAV) procedures have made this action necessary for the safety and management of Instrument Flight Rules (IFR) operations at the above airports.
Establishment of Class E Airspace, Shelton, WA
Document Number: 2016-15184
Type: Rule
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
This action establishes Class E airspace extending upward from 700 feet above the surface at Sanderson Field Airport, Shelton, WA, to accommodate new Standard Instrument Approach Procedures developed for the airport. Controlled airspace is necessary for the safety and management of Instrument Flight Rules (IFR) operations at the airport.
Noise Compatibility Program Notice; San Antonio International Airport; San Antonio, Texas
Document Number: 2016-15183
Type: Notice
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
The Federal Aviation Administration (FAA) announces its findings on the noise compatibility program submitted by San Antonio International Airport under the provisions of 49 U.S.C. (the Aviation Safety and Noise Abatement Act, hereinafter referred to as ``the Act'') and 14 CFR part 150. These findings are made in recognition of the description of Federal and nonfederal responsibilities in Senate Report No. 96-52 (1980). On December 29, 2014, the FAA determined that the noise exposure maps submitted by San Antonio International Airport under part 150 were in compliance with applicable requirements. On June 2, 2015, the FAA approved the San Antonio International Airport noise compatibility program. Both of the recommendations of the program were approved.
Civil Penalties
Document Number: 2016-15118
Type: Rule
Date: 2016-06-28
Agency: Saint Lawrence Seaway Development Corporation, Department of Transportation
This interim final rule updates the maximum civil penalty amounts for violations of statutes and regulations administered by SLSDC pursuant to the Federal Civil Penalties Inflation Adjustment Improvement Act of 2015. This final rule amends our regulations to reflect the new civil penalty amounts for violations of the Seaway Regulations and Rules under the authority of the Ports and Waterways Safety Act of 1972, as amended (PWSA).
Operation and Certification of Small Unmanned Aircraft Systems
Document Number: 2016-15079
Type: Rule
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
The FAA is amending its regulations to allow the operation of small unmanned aircraft systems in the National Airspace System. These changes address the operation of unmanned aircraft systems and certification of their remote pilots. This rule will also prohibit model aircraft from endangering the safety of the National Airspace System.
Airworthiness Directives; Airbus Helicopters
Document Number: 2016-14972
Type: Rule
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for Airbus Helicopters Model AS 365 N3 helicopters. This AD requires inspecting the cabin and cockpit for labels, placards, or markings that provide jettison procedure instructions for cabin doors, removing any labels, placards, or markings that are in an incorrect location, and installing placards where they are missing. This AD is prompted by the determination that placards had not been installed according to specifications on newly manufactured helicopters. The actions are intended to provide exit procedures during an emergency.
Airworthiness Directives; Bombardier, Inc. Airplanes
Document Number: 2016-14971
Type: Proposed Rule
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-102, -103, and -106 airplanes, Model DHC-8-200 series airplanes, and Model DHC-8-300 series airplanes. This proposed AD was prompted by several occurrences of loss of airspeed data on both pilot and co-pilot air speed indicators due to the accumulation of ice on the pitot probes. An investigation revealed that the accumulation of ice was due to inoperative pitot probe heaters. This proposed AD would require replacing the existing circuit breakers in both the left and right side of the pitot heater system with circuit breakers that have higher trip points. We are proposing this AD to prevent circuit breakers from tripping and cutting power supply to the pitot probe heater, which could cause loss of airspeed data and result in the flightcrew not being able to control the airspeed of the airplane.
Airworthiness Directives; Airbus Airplanes
Document Number: 2016-14969
Type: Proposed Rule
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
We are revising an earlier proposed airworthiness directive (AD) for all Airbus Model A318 and A319 series airplanes, A320-211, - 212, -214, -231, -232, and -233 airplanes, and A321 series airplanes. The NPRM proposed to require an inspection to identify the part number and serial number of the main landing gear (MLG) sliding tubes installed on the airplane; and inspection of affected chromium plates for damage; an inspection of affected sliding tube axles for damage; and replacement of the sliding tube if necessary. The NPRM was prompted by a report of a rupture of a MLG sliding tube axle. This action revises the NPRM by removing certain service information that does not adequately address the identified unsafe condition and revising the compliance method. We are proposing this supplemental NPRM (SNPRM) to detect and correct cracks in the axle and (partial) detachment of the axle and wheel from the sliding tube, which could result in failure of an MLG. Since these actions impose an additional burden over those proposed in the NPRM, we are reopening the comment period to allow the public the chance to comment on these proposed changes.
Airworthiness Directives; Airbus Airplanes
Document Number: 2016-14968
Type: Proposed Rule
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Airbus Model A300 series airplanes; Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes); and Model A310 series airplanes. This proposed AD was prompted by a report indicating that during inspections to detect corrosion of the bulk cargo doors, several cracks were discovered. This proposed AD would require a general visual inspection of the bulk cargo door frame to identify any structural repairs, a detailed visual inspection of the frame at the repaired area for any cracking if necessary, and corrective actions if necessary. We are proposing this AD to detect and correct cracking of the bulk cargo doors; such cracking could result in rapid airplane decompression or possible loss of the bulk cargo door.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-14966
Type: Proposed Rule
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-700 and -700C series airplanes. This proposed AD was prompted by a report that for airplanes with blended winglets, the nose-up pitch trim limit and associated warning for the horizontal stabilizer control system will allow take-off with incorrect trim settings. This proposed AD would require, depending on airplane configuration, replacing the pitch trim light plates on the flight deck control stand, relocating the position warning horn switches of the horizontal stabilizer, revising the software, removing the placard, and doing related investigative and corrective actions if necessary. We are proposing this AD to prevent take-off with incorrect settings of the horizontal stabilizer pitch trim system. Settings outside of the appropriate pitch trim limits could result in loss of controllability of the airplane during take-off.
Airworthiness Directives; Bombardier, Inc. Airplanes
Document Number: 2016-14965
Type: Proposed Rule
Date: 2016-06-28
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2A12 (CL-601 Variant), and CL- 600-2B16 (CL-601-3A, CL-601-3R, and CL-604 Variants) airplanes. This proposed AD was prompted by a report that a potential chafing condition exists between the negative-G fuel feed drain line of the auxiliary power unit (APU) and its surrounding structure and components. This proposed AD would require, for certain airplanes, a detailed inspection for chafing conditions of the negative-G fuel feed drain line of the APU, and corrective actions if necessary. For certain other airplanes, this proposed AD would require replacement of the APU negative-G fuel feed tube assembly and the drain line. We are proposing this AD to prevent a chafing condition in the negative-G fuel feed drain line, which can result in fuel leaking from the drain line. Leakage of the negative-G fuel feed drain line is a dormant failure. This condition, in combination with a nearby hot surface or other potential ignition source, could result in an uncontrolled fire in the aft equipment bay.
Airworthiness Directives; Zodiac Seats California LLC Seating Systems
Document Number: 2016-15209
Type: Proposed Rule
Date: 2016-06-27
Agency: Federal Aviation Administration, Department of Transportation
This document announces the reopening of the comment period for the above-referenced NPRM, which proposed the adoption of a new airworthiness directive (AD) that would apply to certain Zodiac Seats California LLC seating systems. The NPRM proposed to require removing affected seating systems. This reopening of the comment period is necessary to ensure that all interested persons have ample opportunity to submit any written relevant data, views, or arguments regarding the proposed requirements of the NPRM.
Nondiscrimination on the Basis of Disability in Air Travel: Third Meeting of the Negotiated Rulemaking Committee
Document Number: 2016-15147
Type: Proposed Rule
Date: 2016-06-27
Agency: Department of Transportation, Office of the Secretary
This notice announces the third meeting of the Advisory Committee on Accessible Air Transportation (ACCESS Advisory Committee).
Pipeline Safety: Gaseous Carbon Dioxide Pipelines
Document Number: 2016-15123
Type: Notice
Date: 2016-06-27
Agency: Pipeline and Hazardous Materials Safety Administration, Department of Transportation
PHMSA is seeking public comment on a PHMSA-authored report titled: ``Background for Regulating the Transportation of Carbon Dioxide in a Gaseous State,'' which is available in the docket at PHMSA-2016-0049. The report evaluates existing and potential future gaseous carbon dioxide (CO2) pipelines and outlines PHMSA's approach for establishing minimum pipeline safety standards for the transportation of carbon dioxide in a gaseous state to fulfill the requirements of section 15 of the Pipeline Safety, Regulatory Certainty, and Job Creation Act of 2011 (the Act). The Act requires the Secretary of Transportation to ``prescribe minimum safety standards for the transportation of carbon dioxide by pipeline in a gaseous state.'' PHMSA is seeking to better understand the possible effects of the regulatory scenarios presented within the report, as well as the locations and extent of gaseous carbon dioxide pipelines, and is requesting feedback on the validity and applicability of these effects and the location and extent of these pipelines. As PHMSA does not currently regulate these pipelines, its ability to reach out and locate operators of gaseous carbon dioxide pipelines has been limited and it is unclear if PHMSA's current information is comprehensive.
Reports, Forms, and Recordkeeping Requirements
Document Number: 2016-15112
Type: Notice
Date: 2016-06-27
Agency: National Highway Traffic Safety Administration, Department of Transportation
Before a Federal agency can collect certain information from the public, it must receive approval from the Office of Management and Budget (OMB). Under procedures established by the Paperwork Reduction Act of 1995, before seeking OMB approval, Federal agencies must solicit public comment on proposed collections of information, including extensions and reinstatement of previously approved collections. This document describes a collection of information for which NHTSA intends to seek OMB approval.
Request for Transit Advisory Committee for Safety (TRACS) Nominations
Document Number: 2016-15110
Type: Notice
Date: 2016-06-27
Agency: Federal Transit Administration, Department of Transportation
The Federal Transit Administration (FTA) is seeking nominations for individuals to serve as members for two-year terms on the Transit Advisory Committee for Safety (TRACS). TRACS provides information, advice, and recommendations to the U.S. Secretary of Transportation (Secretary) and FTA Administrator in response to tasks assigned to the committee. TRACS does not exercise program management responsibilities and makes no decisions directly affecting the programs on which it provides advice. The Secretary may accept or reject a recommendation made by TRACS and is not bound to pursue any recommendation from TRACS.
Hazardous Materials: Information Collection Activities
Document Number: 2016-15069
Type: Notice
Date: 2016-06-27
Agency: Pipeline and Hazardous Materials Safety Administration, Department of Transportation
In accordance with the Paperwork Reduction Act of 1995, PHMSA invites comments on an information collection pertaining to hazardous materials transportation for which PHMSA intends to request renewal from the Office of Management and Budget (OMB).
Federal Civil Penalties Inflation Adjustment of 2015
Document Number: 2016-14973
Type: Rule
Date: 2016-06-27
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA amends the civil penalties listed in its regulations to ensure that the civil penalties assessed or enforced by the Agency reflect the statutorily mandated ranges as adjusted for inflation. Pursuant to the Federal Civil Penalties Inflation Adjustment Act Improvements Act of 2015 (2015 Act), FMCSA is required to promulgate a catch-up adjustment through an interim final rule. Pursuant to the Administrative Procedure Act, FMCSA finds that good cause exists for immediate implementation of this interim final rule because prior notice and comment are unnecessary, per the specific provisions of the 2015 Act.
Airworthiness Directives; Saab AB, Saab Aeronautics (Type Certificate Previously Held by Saab AB, Saab Aerosystems) Airplanes
Document Number: 2016-14871
Type: Rule
Date: 2016-06-27
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Saab AB, Saab Aeronautics Model 340A (SAAB/SF340A) and SAAB 340B airplanes. This AD was prompted by reports of ruptured horizontal stabilizer de-icing boots. This AD requires a revision of the applicable airplane flight manual (AFM), repetitive inspections of the horizontal stabilizer de-icing boots, and applicable corrective actions. We are issuing this AD to detect and correct damage of the de- icing boot; such damage could lead to a ruptured boot, severe vibrations, and possible reduced control of the airplane.
Metropolitan Planning Organization Coordination and Planning Area Reform
Document Number: 2016-14854
Type: Proposed Rule
Date: 2016-06-27
Agency: Federal Highway Administration, Department of Transportation, Federal Transit Administration
The FHWA and FTA propose revisions to the transportation planning regulations to promote more effective regional planning by States and metropolitan planning organizations (MPO). The goal of the proposed revisions is to result in unified planning products for each urbanized area (UZA), even if there are multiple MPOs designated within that urbanized area. Specifically it would result in MPOs developing a single metropolitan transportation plan, a single transportation improvement program (TIP), and a jointly established set of performance targets for the entire urbanized area and contiguous area expected to become urbanized within a 20-year forecast period for the transportation plan. If multiple MPOs are designated within that urbanized area, they would jointly prepare these unified planning products. To accomplish this, the proposed revisions clarify that the metropolitan planning area must include the entire urbanized area and contiguous area expected to become urbanized within 20 years. These proposed revisions would better align the planning regulations with statutory provisions concerning the establishment of metropolitan planning area (MPA) boundaries and the designation of MPOs. This includes the statutory requirement for the MPA to include an urbanized area in its entirety, and the exception provision to allow more than one MPO to serve a single MPA if warranted by the size and complexity of the MPA. The rulemaking would establish clearer operating procedures, and reinstate certain coordination and decisionmaking requirements for situations where there is more than one MPO serving an MPA. The proposed rule includes a requirement for unified planning products for the MPA including jointly established performance targets within an MPA, and a single metropolitan transportation plan and TIP for the entire MPA in order to result in planning products that reflect the regional needs of the entire urbanized area. These unified planning products would be jointly developed by the multiple MPOs in such MPAs where more than one MPO is designated. The FHWA and FTA propose to phase in implementation of these proposed coordination requirements and the proposed requirements for MPA boundary and MPO boundaries agreements over 2 years.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-14752
Type: Rule
Date: 2016-06-27
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 767 airplanes. This AD was prompted by a determination that certain splice plate locations of the aft pressure bulkhead web are hidden and cannot be inspected using existing manufacturer service information. This AD requires repetitive open-hole high frequency eddy current (HFEC) inspections for cracking of the aft pressure bulkhead web. We are issuing this AD to detect and correct cracking in the aft pressure bulkhead web, which could result in rapid airplane decompression and loss of structural integrity.
Prisoner Transportation Services, LLC-Control-U.S. Corrections, LLC D/B/A U.S.C.
Document Number: 2016-15009
Type: Notice
Date: 2016-06-24
Agency: Surface Transportation Board, Department of Transportation
On May 26, 2016, Prisoner Transportation Services, LLC (Applicant) filed an application under 49 U.S.C. 14303 so that it can acquire common control of U.S. Corrections, LLC (U.S.C.). The Board is tentatively approving and authorizing the transaction, and, if no opposing comments are timely filed, this notice will be the final Board action. Persons wishing to oppose the application must follow the rules at 49 CFR 1182.5 and 1182.8.
Aston Martin Lagonda Limited; Denial of Petition for Decision of Inconsequential Noncompliance
Document Number: 2016-14964
Type: Notice
Date: 2016-06-24
Agency: National Highway Traffic Safety Administration, Department of Transportation
Aston Martin Lagonda Limited (AML), has determined that certain model year (MY) 2009-2015 Aston Martin DB9 two-door and four- door passenger cars do not fully comply with paragraph S4.3 of Federal Motor Vehicle Safety Standard (FMVSS) No. 206, Door locks and door retention components. Aston Martin Lagonda of North America, Inc., filed a report dated December 16, 2015, pursuant to 49 CFR part 573, Defect and Noncompliance Responsibility and Reports for AML. AML then petitioned NHTSA under 49 CFR part 556 requesting a decision that the subject noncompliance is inconsequential to motor vehicle safety.
Pipeline Safety: Public Workshop on Underground Natural Gas Storage Safety
Document Number: 2016-14953
Type: Notice
Date: 2016-06-24
Agency: Pipeline and Hazardous Materials Safety Administration, Department of Transportation
This notice announces a public meeting to solicit input and obtain background information concerning underground natural gas storage safety. PHMSA and the National Association of Pipeline Safety Representatives (NAPSR) are co-sponsoring this one-day workshop. The workshop will bring federal and state regulators, emergency responders, industry, and interested members of the public together to participate in understanding and shaping the future for maintaining the safety of underground natural gas storage facilities. PHMSA and NAPSR recognize that the October, 2015, Southern California Gas Company's (SoCal Gas) Aliso Canyon underground natural gas storage facility leak on Well SS25 located in the Porter Ranch area near Los Angeles, California, has drawn concerns regarding natural gas storage well safety and the environmental effects of an incident. Currently, throughout the United States, approximately 400 interstate and intrastate underground natural gas storage facilities are operating with more than four trillion cubic feet of natural gas working capacity.
Amendment of Class D and Class E Airspace; Charlottesville, VA
Document Number: 2016-14881
Type: Rule
Date: 2016-06-24
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E Airspace Designated as an Extension to a Class D at Charlottesville-Albemarle Airport, Charlottesville, VA, as the Azalea Park Non-Directional Radio Beacon (NDB) has been decommissioned requiring airspace reconfiguration at the airport. Also, the Notice to Airmen (NOTAM) part time status is removed from this airspace. This action also updates the geographic coordinates of the above airport and the University of Virginia Medical Center Heliport in Class D and E airspace listed in this final rule. This action enhances the safety and management of Instrument Flight Rules (IFR) operations in the area.
Proposed Amendment of Class E Airspace, Indiana, PA
Document Number: 2016-14880
Type: Proposed Rule
Date: 2016-06-24
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to amend Class E airspace at Indiana, PA, to accommodate the new runway at Indiana County Airport (Jimmy Stewart Field). Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations at the airport. This action also would update the geographic coordinates of airport.
Proposed Amendment of Class E Airspace; Santa Rosa, CA
Document Number: 2016-14879
Type: Proposed Rule
Date: 2016-06-24
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to modify Class E airspace designated as an extension to a Class D airspace at Charles M. Schulz-Sonoma County Airport, Santa Rosa, CA, by reducing the segment extending northwest of the airport and adding a segment southeast of the airport. This action also proposes to modify Class E airspace extending upward from 700 feet above the surface to include only that area required for Instrument Flight Rules (IFR) operations at the airport. Additionally, this action updates the airport's geographic coordinates for both Class D and E airspace areas. A review of the airspace has made this proposal necessary for the safety and management of Standard Instrument Approach Procedures for IFR operations at the airport.
Establishment of Class E Airspace; Lisbon, ND
Document Number: 2016-14873
Type: Rule
Date: 2016-06-24
Agency: Federal Aviation Administration, Department of Transportation
This action establishes Class E airspace in Lisbon, ND. Controlled airspace is necessary to accommodate new Area Navigation (RNAV) Standard Instrument Approach Procedures at Lisbon Municipal Airport. The FAA is taking this action to enhance the safety and management of Instrument Flight Rule (IFR) operations at the airport.
Airworthiness Directives; General Electric Company Turbofan Engines
Document Number: 2016-14474
Type: Rule
Date: 2016-06-24
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all General Electric Company (GE) GE90-76B, GE90-77B, GE90-85B, GE90-90B, and GE90-94B turbofan engines. This AD was prompted by an uncontained failure of the high-pressure compressor (HPC) stage 8-10 spool, leading to an airplane fire. This AD requires eddy current inspection (ECI) or ultrasonic inspection (USI) of the HPC stage 8-10 spool and removing from service those parts that fail inspection. We are issuing this AD to prevent failure of the HPC stage 8-10 spool, uncontained rotor release, damage to the engine, and damage to the airplane.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.