Federal Aviation Administration November 2010 – Federal Register Recent Federal Regulation Documents

This notice announces three fact-finding informal airspace meetings to solicit information from airspace users and others concerning a proposal to revise the Class B airspace area at Salt Lake City, UT. The purpose of these meetings is to provide interested parties an opportunity to present views, recommendations, and comments on the proposal. All comments received during these meetings will be considered prior to any revision or issuance of a notice of proposed rulemaking.

The FAA is issuing this notice to advise the public of a meeting of the Executive Committee of the Aviation Rulemaking Advisory Committee.

This final rule adjusts for inflation the minimum and maximum civil monetary penalty amounts the FAA may impose for violations of the statutes and regulations it enforces in order to continue the deterrent effect of these penalties. The adjustments are made following a formula provided by Congress.

This action proposes to amend Class E Airspace at Newport, VT, as the Newport Non-Directional Beacon (NDB) has been decommissioned and new Standard Instrument Approach Procedures (SIAPs) have been developed at Newport State Airport. This action would enhance the safety and airspace management of Instrument Flight Rules (IFR) operations at the airport.

This action will modify existing Class E airspace at Portland, OR, to accommodate aircraft using the Localizer/Distance Measuring Equipment (LOC/DME) Standard Instrument Approach Procedures (SIAPs) at Portland International Airport. This will improve the safety and management of Instrument Flight Rules (IFR) operations at the airport. This action also would adjust the geographic coordinates for the airports and the Corvallis VHF Omni-Directional Radio Range/Distance Measuring Equipment (VOR/DME).

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on August 27, 2010, vol. 75, no. 166, page 52802-52803. This information collection is used to allocate slots and maintain accurate records of slot transfers at High Density Traffic Airports. The information is provided by air carriers and commuter operators, or other persons holding a slot at High Density Airports.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 224: Airport Security Access Control Systems.

Pursuant to Section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463, 5 U.S.C. App. 2), notice is hereby given of a teleconference of the Space Transportation Operations Working Group (STOWG) of the Commercial Space Transportation Advisory Committee (COMSTAC). The teleconference will take place on Wednesday, December 8, 2010, starting at 11 a.m. Eastern Standard Time. Individuals who plan to participate should contact Susan Lender, DFO, (the Contact Person listed below) by phone or e-mail for the teleconference call in number. The proposed agenda for this teleconference is to continue the discussion started during the October 6, 2010, working group meeting. This discussion will include looking at the orbital debris questions asked by the FAA; continuing the group's review of the Concept of Operation for Global Space Vehicle Debris Threat Management Report, and updating the list of top issues that should require the working group's attention. Interested members of the public may submit relevant written statements for the COMSTAC working group members to consider under the advisory process. Statements may concern the issues and agenda items mentioned above or additional issues that may be relevant for the U.S. commercial space transportation industry. Interested parties wishing to submit written statements should contact Susan Lender, DFO, (the Contact Person listed below) in writing (mail or e- mail) by December 1, 2010, so that the information can be made available to COMSTAC members for their review and consideration before the December 8, 2010, teleconference. Written statements should be supplied in the following formats: One hard copy with original signature or one electronic copy via e-mail. An agenda will be posted on the FAA Web site at https://www.faa.gov/ go/ast. Individuals who plan to participate and need special assistance should inform the Contact Person listed below in advance of the meeting.

This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2010-19-51, which was sent previously to all known U.S. owners and operators of the specified model Bell Helicopter Textron Canada (Bell) helicopters by individual letters. This AD requires inspecting parts of the main rotor hydraulic servo actuator (servo actuator) for certain conditions and replacing any unairworthy parts before further flight. This AD is prompted by a collective servo actuator malfunction and a subsequent investigation that revealed the output piston rod assembly (piston rod) had fractured at the threaded end because of stress corrosion cracking. Also, during the investigation of that servo actuator malfunction, a nonconforming grind relief was discovered on a separate piston rod. The actions specified by this AD are intended to detect corrosion or a nonconforming piston rod that, if not detected and corrected, could result in failure of the piston rod, failure of the servo actuator, and subsequent loss of control of the helicopter.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires doing a one-time general visual inspection for a keyway in two fuel tank access door cutouts, and related investigative and corrective actions if necessary. This AD was prompted by reports of cracks emanating from the keyway of the fuel tank access hole. We are issuing this AD to detect and correct such cracking, which could result in the loss of the lower wing skin load path and consequent structural failure of the wing.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires a one-time visual inspection of the No. 3 bearing oil pressure tube, part number (P/N) 51J041-01, P/N 50J604-01, or P/N 50J924-01. Tubes that are found cracked or repaired must be removed from service. This AD also prohibits repaired tubes from being installed. This AD results from one report of a repaired No. 3 bearing oil tube that caused an engine in-flight shutdown, seven reports of repaired No. 3 bearing oil pressure tubes found cracked that led to unscheduled engine removals, and one report of a test cell event from a repaired tube that cracked. We are issuing this AD to prevent cracking of No. 3 bearing oil pressure tubes, which could result in internal oil fire, failure of the high-pressure turbine (HPT) disks, uncontained engine failure, and damage to the airplane.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

These special conditions are issued for the Boeing Model 787-8 airplane. This airplane will have novel or unusual design features when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. The Boeing Model 787-8 airplane will incorporate a fuel tank nitrogen generation system (NGS) that actively reduces flammability exposure within the main fuel tanks significantly below that required by the fuel tank flammability regulations. Among other benefits, this significantly reduces the potential for fuel vapor ignition caused by lightning strikes. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 206: EUROCAE WG 76 Plenary: AIS and MET Data Link Services.

The FAA is issuing this notice to advise the public of a meeting of the RTCA Program Management Committee.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD would require repetitive inspections for damage of the electrical terminal at the left and right flightdeck window 1, and corrective actions if necessary. This proposed AD would also allow for replacing the flightdeck window 1 with a new improved flightdeck window equipped with different electrical connections, which would terminate the repetitive inspections for that flightdeck window 1. This proposed AD was prompted by several reports of electrical arcs at the terminal blocks of the electrically heated flightdeck window 1. We are proposing this AD to prevent smoke and fire in the cockpit, which could lead to loss of visibility, and injuries to or incapacitation of the flightcrew.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

The FAA proposes to amend various airworthiness standards for transport category airplanes. This action would harmonize the requirements for takeoff speeds, static lateral-directional stability, speed increase and recovery characteristics, and the stall warning margin for the landing configuration in icing conditions with the European Aviation Safety Agency (EASA) certification standards. When airplanes are type certificated to both sets of standards, differences between the standards can result in additional costs to manufacturers and operators. Adopting this proposal would harmonize regulatory differences for the items noted above between United States (U.S.) and EASA airworthiness standards.

We propose to adopt a new airworthiness directive (AD) for the products listed above that would supersede an existing AD. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

These special conditions are issued for the Bombardier Inc. Model CL-600-2E25 airplane. This airplane will have a novel or unusual design feature associated with a command-by-wire (CBW) rudder-control system, which requires a source of continuous electrical power to operate the control system. The current 14 CFR part 25.1351(d), ``Operation without normal electrical power,'' requires safe operation in VFR conditions for at least five minutes with inoperative normal electrical power. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

Pursuant to Section 14(a)(2)(A) of the Federal Advisory Committee Act (Pub. L. 92-463, 5 U.S.C. App. 2), and 5 USC552b (c), and in accordance with Sec. 102-3.65, Title 41 of the Code of Federal Regulations, notice is hereby given that the Commercial Space Transportation Advisory Committee (COMSTAC) has been renewed for a 2- year period beginning November 17, 2010. The primary purpose of the Committee is to provide information, advice, and recommendations to the U.S. Department of Transportation (DOT) on matters concerning the U.S. commercial space transportation industry. The primary goals of the Committee are to evaluate economic, technological, and institutional developments relating to the industry; to provide a forum for the discussion of problems involving the relationship between industry activities and government requirements; and to make recommendations to DOT on issues and approaches for Federal policies and programs regarding the industry. The Committee will operate in accordance with the rules of the Federal Advisory Committee Act and the Department of Transportation, FAA Committee Management Order (1110.30C).

This amendment adopts a new airworthiness directive (AD) for the specified ECF model helicopters. This AD results from a mandatory continuing airworthiness information (MCAI) AD issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community. The MCAI AD states that EASA received a report of a rear hinged door on a Model AS332L1 helicopter opening in flight without loss of the door. Examinations revealed incorrect positioning of a door catch that resulted in incorrect locking and uncontrolled opening of the door. This condition, if not detected and corrected, can lead to the loss of the hinged door in flight, damage to the main or tail rotor blades, and subsequent loss of control of the helicopter.