Historic Preservation, Advisory Council July 2015 – Federal Register Recent Federal Regulation Documents

In accordance with the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.), this notice announces that the U.S. Department of Transportation (DOT) will forward the Information Collection Request (ICR) abstracted below to the Office of Management and Budget (OMB) for reinstatement with change of a previously approved collection. The ICR describes the nature of the information collection and its expected cost and burden hours. The OMB approved the form in 2009 with its renewal required by September 30, 2012. Subsequently, DOT was given approval of the form until August 31, 2014. The renewal period then lapsed; therefore, the form expired. The Federal Register Notice with a 60-day comment period soliciting comments on the form renewal was published on April 29, 2015, [FR Vol. 80, No. 82, page 23855]. No comments were received. This notice includes corrections and updates to the 60-day published notice.

The Federal Aviation Administration (FAA) announces that the Draft Written Re-Evaluation of the O'Hare Modernization Environmental Impact Statement (Draft Re-Evaluation) for Chicago O'Hare International Airport, Chicago, Illinois is available for public review and comment. The Draft Re-Evaluation identifies the potential environmental impacts associated with the construction schedule modification that alters the timing for commissioning new Runway 10R/28L, new Runway 9C/ 27C, and the extension of Runway 9R/27L at O'Hare International Airport pursuant to the National Environmental Policy Act. The FAA will host Public Workshops on the Draft Re-Evaluation. The Public Workshops on the Draft Re-Evaluation will be held on the following dates: Monday, August 10, 2015, at White Eagle Banquets, 6839 North Milwaukee Avenue, Niles, Illinois 60714; Tuesday, August 11, 2015, at Taft High School, 6530 West Bryn Mawr Avenue, Chicago, Illinois 60631; Wednesday, August 12, 2015, at Monty's Elegant Banquets, 703 South York Road, Bensenville, Illinois 60106; Thursday, August 13, 2015, at Belvedere Events and Banquets, 1170 West Devon Avenue, Elk Grove Village, Illinois 60007. Each Public Workshops will start at 1 p.m. (Central Standard Time), and registration to participate in the Public Workshops will conclude by 9 p.m. (Central Standard Time). Representatives of FAA and its consultants will be available to provide information about the Draft Re-Evaluation. Spanish language translators will be available at the Public Workshops. If you need the assistance of a translator, other than Spanish, please call Ms. Amy Hanson at (847) 294-7354 by August 3, 2015. The comment period is open as of Monday, July 27, 2015, and closes Wednesday, August 26, 2015. All comments are to be submitted to Amy Hanson of the FAA, at the address shown below. The comments must be postmarked and email must be sent by no later than midnight, Wednesday, August 26, 2015.

This notice announces the existence of and requests comments on the proposed airworthiness design standards for acceptance of the AutoGyro Model Calidus gyroplane under the regulations for primary category aircraft.

The Federal Motor Carrier Safety Administration (FMCSA) requests public comment on an application for exemption from Volvo Trucks of North America (Volvo) to allow the placement of rain and ambient light detection sensors on Volvo commercial motor vehicles (CMV) lower in the windshield than is currently permitted by the Agency's regulations in order to utilize a mounting location that allows the sensor to function correctly. The Federal Motor Carrier Safety Regulations (FMCSRs) currently require antennas, transponders, and similar devices to be located not more than 6 inches below the upper edge of the windshield, outside the area swept by the windshield wipers, and outside the driver's sight lines to the road and highway signs and signals. Volvo believes that mounting the sensor lower in the windshield will allow it to function properly while maximizing the external view of the road and maintaining an adequate forward facing field of view for the driver.

FMCSA announces its decision to renew the exemptions from the vision requirement in the Federal Motor Carrier Safety Regulations for 13 individuals. FMCSA has statutory authority to exempt individuals from the vision requirement if the exemptions granted will not compromise safety. The Agency has concluded that granting these exemption renewals will provide a level of safety that is equivalent to or greater than the level of safety maintained without the exemptions for these commercial motor vehicle (CMV) drivers.

We propose to supersede Airworthiness Directive (AD) 2012-15- 13, which applies to certain The Boeing Company Model 747-100B SUD, 747-300, 747-400, and 747-400D series airplanes; and Model 747-200B series airplanes having a stretched upper deck. AD 2012-15-13 currently requires inspections for cracking and discrepancies of certain fasteners; modification of the frame-to-tension-tie joints; repetitive post-modification inspections; related investigative and corrective actions if necessary; and repetitive inspections for cracking in the tension tie channels, and repair if necessary. For certain airplanes, AD 2012-15-13 also requires an inspection to determine if the angle is installed correctly, and re-installation if necessary; and an inspection at the fastener locations where the tension tie previously attached to the frame prior to certain modifications, and repair if necessary. Since we issued AD 2012-15-13, an evaluation indicated that the upper deck is subject to widespread fatigue damage (WFD). This proposed AD would add a new inspection for cracking in the tension tie channels and post-modification inspections of the modified tension ties for cracking, and repair if necessary. We are proposing this AD to prevent fatigue cracking of the tension ties, shear webs, and frames of the upper deck, which could result in rapid decompression and reduced structural integrity of the airplane.

The Federal Aviation Administration (FAA) has revised its procedures for implementing the National Environmental Policy Act (NEPA) by issuing Order 1050.1F, Environmental Impacts: Policies and Procedures. Order 1050.1F cancels Order 1050.1E, Environmental Impacts: Policies and Procedures. The revisions in Order 1050.1F include reorganization of the Order to make it easier to use, clarification of requirements, additions to the list of Categorical Exclusions (CATEXs), updating of policies and procedures to be consistent with recent guidance, addition of provisions for emergency actions, and updating of terminology to incorporate the Next Generation Air Transportation System (NextGen). The FAA issued a notice and request for comment in the Federal Register on August 14, 2013 (78 FR 49596). All comments received were considered in the issuance of the final Order. This notice summarizes the changes made to Order 1050.1E and includes responses to substantive comments received.

We are superseding Airworthiness Directive (AD) 2004-13-02, which applied to certain The Boeing Company Model 747-100, -200B, and - 200F series airplanes. AD 2004-13-02 required repetitive inspections to find discrepancies in the upper and lower skins of the fuselage lap joints, and repair if necessary. This new AD adds post-repair inspections for cracking and corrosion, and repair if necessary; structural modification at the lap joints; and post-modification inspections for cracking and corrosion, and repair if necessary. This AD was prompted by an evaluation by the design approval holder (DAH) that indicates the longitudinal lap joints are subject to widespread fatigue damage (WFD). The actions mandated by this AD are necessary to reach the limit of validity (LOV). We are issuing this AD to detect and correct fatigue cracking in the upper and lower skins of the fuselage lap joints, which could result in sudden fracture and failure of a lap joint and rapid in-flight decompression of the airplane fuselage.

We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by reports of wear of the trimmable horizontal stabilizer actuator (THSA). This AD requires repetitive inspections of the THSA for damage, and replacement if necessary; and replacement of the THSA after reaching a certain life limit. We are issuing this AD to detect and correct wear on the THSA, which would reduce the remaining life of the THSA, possibly resulting in premature failure and consequent reduced control of the airplane.

We are superseding Airworthiness Directive (AD) 2012-13-06, for all Airbus Model A300 series airplanes and all Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). AD 2012-13-06 required a one-time detailed inspection to determine the length of the fire shut-off valve (FSOV) bonding leads and for contact or chafing of the wires, and corrective actions if necessary. This new AD requires a new one-time detailed inspection of the FSOV bonding leads to ensure that the correct bonding leads are inspected, and corrective action if necessary. This AD was prompted by a determination that the description of the inspection area specified in the service information was misleading; therefore, some operators might have inspected incorrect bonding leads. We are issuing this AD to detect and correct contact or chafing of wires and the bonding leads, which, if not detected, could be a source of sparks in the wing trailing edge, and could lead to an uncontrolled engine fire.

We are adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model 4101 airplanes. This AD requires a one-time inspection for damage of the stop arms of the stop plates, an adjustment of the electric trim limit switches, and replacement of the stop plates with newly manufactured stop plates if necessary. This AD was prompted by a report that the pitch trim jammed in the fully down position. We are issuing this AD to detect and correct broken stop arms of the stop plates, which could lead to the pitch trim jamming, loss of control of the elevator trim, and possible reduced control of the airplane.

The Federal Aviation Administration (FAA) is publishing this notice to announce that the physical address of the FAA Southwest Regional Office, which is specified in airworthiness directives (ADs) issued by the Rotorcraft Directorate, is changing due to a relocation.

The Federal Aviation Administration (FAA) is considering a proposal from the Kansas City Aviation Department (sponsor), Kansas City, MO, to release a 14.94

We propose to adopt a new airworthiness directive (AD) for all The Boeing Company Model 787 airplanes. This proposed AD was prompted by the disclosure that the inner diameters of some batches of landing gear pins were not shot peened in accordance with design specifications and need to be replaced. This proposed AD would require inspection for improperly manufactured landing gear pins, and replacement if necessary. We are proposing this AD to detect and correct insufficient shot peening that could lead to stress corrosion cracking and failure of the landing gear pin, and cause landing gear collapse and inability to control the airplane at high speeds on the ground.

We propose to supersede airworthiness directive (AD) 2014-07- 52 for certain Airbus Helicopters (previously Eurocopter France) Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D, AS350D1, AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters. AD 2014-07-52 currently requires repetitively inspecting certain reinforcement angles of the rear structure to tailboom junction frame (reinforcement angles) for a crack at 10 hour time-in-service (TIS) intervals, repairing any cracked reinforcement angle, and allows an optional repetitive inspection with a 165 hour TIS inspection interval as a terminating action for the 10 hour TIS inspections. This proposed AD would retain the inspection requirements of AD 2014-07-52 and require the inspection of the area around each reinforcement angle screw hole as terminating action to the 10 hour TIS inspections. These proposed actions are intended to detect a crack in the reinforcement angle, which if not corrected, could result in loss of the tailboom and subsequent loss of control of the helicopter.

Pursuant to the Pipeline Inspection, Protection, Enforcement, and Safety (PIPES) Act of 2006, this final rule establishes review criteria for State excavation damage prevention law enforcement programs as a prerequisite for PHMSA to conduct an enforcement proceeding against an excavator in the absence of an adequate enforcement program in the State where a pipeline damage prevention violation occurs. This final rule amends the pipeline safety regulations to establish the following: Criteria and procedures for determining the adequacy of State pipeline excavation damage prevention law enforcement programs; an administrative process for making State adequacy determinations; the Federal requirements PHMSA will enforce in States with inadequate excavation damage prevention law enforcement programs; and the adjudication process for administrative enforcement proceedings against excavators where Federal authority is exercised. The development of the review criteria and the subsequent determination of the adequacy of State excavation damage prevention law enforcement programs is intended to encourage States to develop effective excavation damage prevention law enforcement programs to protect the public from the risk of pipeline ruptures caused by excavation damage and allow for Federal administrative enforcement action in States with inadequate enforcement programs.

This notice contains a summary of a petition seeking relief from specified requirements of Title 14, Code of Federal Regulations (14 CFR). The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of the FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

The Federal Transit Administration (FTA) received a request for a waiver to permit the purchase of a Variable Refrigerant Flow (VRF) HVAC system that is non-compliant with Buy America requirements using FTA funding. The request is from the City of Kansas City, Missouri (Kansas City) for its Vehicle Maintenance Facility (VMF) associated with the Kansas City Downtown Streetcar Project. In accordance with 49 U.S.C. 5323(j)(3)(A), FTA is providing notice of the waiver request and seeks public comment before deciding whether to grant the request. If granted, the waiver would apply only to the FTA- funded procurement of a VRF HVAC system by Kansas City.

This action modifies and establishes Class E airspace at Bremerton National Airport, Bremerton, WA, to accommodate new Standard Instrument Approach Procedures (SIAPs) at Bremerton National airport due to the decommissioning of the Kitsap non-directional radio beacon (NDB). The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations at the airport.

The Federal Aviation Administration is requesting public comment on a request by the Coastal Carolina Regional Airport to change the use of a portion of airport property at the Coastal Carolina Regional Airport. The request consists of approximately 11.7 acres for use as a future non-aeronautical development area. This action is taken under the provisions of Section 125 of the Wendell H. Ford Aviation Investment Reform Act for the 21st Century (AIR 21).

We are adopting a new airworthiness directive (AD) for all Pratt & Whitney (PW) JT8D-217C and JT8D-219 turbofan engines. This AD was prompted by reports of cracking in the low-pressure turbine (LPT) shaft. This AD requires removing affected LPT shafts from service using a drawdown plan. We are issuing this AD to prevent failure of the LPT shaft, which could lead to an uncontained engine failure and damage to the airplane.