Federal Aviation Administration 2014 – Federal Register Recent Federal Regulation Documents

This action amends Class E airspace within the Grand Forks, ND, area by amending the geographic coordinates of the Grand Forks International Airport ILS Localizer. The boundaries and operating requirements of the airspace remain the same.

We are adopting a new airworthiness directive (AD) for certain Alpha Aviation Concept Limited Model R2160 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the metal screen shield over the ignition switch may ground out the ignition terminals. We are issuing this AD to require actions to address the unsafe condition on these products.

We are superseding Airworthiness Directive (AD) 2007-16-19, which applied to certain The Boeing Company Model 747-200B, 747-300, and 747-400 series airplanes. AD 2007-16-19 required repetitive detailed inspections for cracking of the aft tension tie channels from body station (BS) 1120 to BS 1220 and from BS 880 to BS 1100, and corrective actions if necessary. AD 2007-16-19 also provided optional terminating action. This new AD retains the existing requirements, limits the area of the detailed inspection, adds repetitive surface high-frequency eddy current inspections, and mandates the previously optional terminating action. This AD was prompted by an analysis that indicated the need to mandate the previously optional modification. We are issuing this AD to prevent fatigue cracking of the tension ties, which could result in reduced structural integrity of the airplane and rapid depressurization of the airplane.

This action amends a typographical error in the geographic coordinates of South St. Paul Municipal Airport-Richard E. Fleming Field in a final rule technical amendment published in the Federal Register of March 4, 2014, that amends Class D airspace in the St. Paul, MN, area.

This action proposes to establish Class E airspace extending upward from 1,200 feet above the surface within the boundary of the state of North Dakota. With the increased use of GPS/GNSS navigation systems, pilots routinely file and fly flight plans using point-to- point routes instead of published airways. Often, these point-to-point routes take aircraft through uncontrolled airspace (Class G). With this proposal, Minneapolis Air Route Traffic Control Center (ARTCC) would provide a more expeditious service and increased efficiency within the National Airspace System (NAS).

This action proposes to amend Class E airspace extending upward from 1,200 feet above the surface within the boundary of the state of South Dakota. With the increased use of GPS/GNSS navigation systems, pilots routinely file and fly flight plans using point-to- point routes instead of published airways. Often, these point-to-point routes take aircraft through uncontrolled airspace (Class G). With this proposal, Minneapolis Air Route Traffic Control Center (ARTCC) would provide more expeditious service and increased efficiency within the National Airspace System.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The FAA/AST will collect lessons learned from members of the commercial space industry in order to carry out the safety responsibilities in 49 U.S.C. Chapter 701 Section 70103 (c).

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The FAA uses the information gathered from Grand Canyon National Park air tour operators to monitor their compliance with the Federal regulations.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The respondents to this information collection are CFR Part 135 and Part 121 operators. The FAA uses the information to ensure compliance and adherence to the regulations.

The Federal Aviation Administration is requesting public comment on the release of land at the Piedmont Triad International Airport, Greensboro, North Carolina. This property, approximately 16.93 acres of fee simple release, will change to a non-aeronautical use. This action is taken under the provisions of Section 125 of the Wendell H. Ford Aviation Investment Reform Act for the 21st Century (AIR 21).

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This proposed AD was prompted by reports of fatigue cracking in certain areas. This proposed AD would require repetitive inspections for cracking of the skin assembly and bear strap of the forward airstair stowage doorway; post-repair and post- modification inspections for certain airplanes; and related investigative and corrective actions, if necessary. This proposed AD would also provide optional terminating actions for certain repetitive inspections. We are proposing this AD to detect and correct fatigue cracking, which could result in rapid loss of cabin pressure.

We are adopting a new airworthiness directive (AD) for certain M7 Aerospace LLC Models SA26-T, SA26-AT, SA226-AT, SA226-T, SA226-T(B), SA226-TC, SA227-AC (C-26A), SA227-AT, SA227-TT, SA227-BC (C-26A), SA227-CC, and SA227-DC (C-26B) airplanes. This AD was prompted by reports of jamming of the aileron control cable chain in the pilot and copilot control columns due to inadequate lubrication and maintenance of the chain. This AD requires repetitively replacing and lubricating the aileron chain, sprocket, and bearings in the control columns. We are issuing this AD to correct the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777F series airplanes. This AD was prompted by a report of a fire that originated near the first officer's seat and caused extensive damage to the flight deck. This AD requires replacing the low-pressure oxygen hoses with non-conductive low-pressure oxygen hoses in the stowage box and supernumerary ceiling area. We are issuing this AD to prevent electrical current from passing through an internal, anti-collapse spring of the low-pressure oxygen hose, which can cause the low-pressure oxygen hose to melt or burn and lead to an oxygen-fed fire near the flight deck.

We are superseding Airworthiness Directive (AD) 2000-11-06 for certain The Boeing Company Model 767 airplanes. AD 2000-11-06 required repetitive inspections to detect discrepancies of the wiring and surrounding Teflon sleeves of the fuel tank boost pumps and override/ jettison pumps; replacement of the sleeves with new sleeves, for certain airplanes; and repair or replacement of the wiring and sleeves with new parts, as necessary. This new AD requires reducing the initial compliance time and repetitive inspection interval in AD 2000-11-06; mandates a terminating action for the repetitive inspections to eliminate wire damage; removes certain airplanes from the applicability; and requires revising the maintenance program to incorporate changes to the airworthiness limitations section. This AD was prompted by fleet information indicating that the repetitive inspection interval in AD 2000-11-06 is too long, because excessive chafing of the sleeving continues to occur much earlier than expected between scheduled inspections. We are issuing this AD to detect and correct chafing of the fuel pump wire insulation and consequent exposure of the electrical conductor, which could result in electrical arcing between the wires and conduit and consequent fire or explosion of the fuel tank.

The Federal Aviation Administration (FAA) is issuing this notice to advise the public that the Draft Written Reevaluation for a minor adjustment to a project evaluated in FAA's 2005 Final Environmental Impact Statement (FEIS) for the LAX Master Plan will be made available for public comment. The Draft Written Reevaluation has been prepared for the construction and operation of the proposed West Aircraft Maintenance Area (WAMA) west of Taxiway AA in the southwest quadrant of Los Angeles International Airport, Los Angeles, California. FAA is seeking comments on the Draft Written Reevaluation.

The FAA is issuing this notice to advise the public of the fifth meeting of the RTCA Tactical Operations Committee.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This rule amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

This rule establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request from the Office of Management and Budget (OMB) approval to renew an information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on February 11, 2014, vol. 79, no. 28, pages 8231-8232. The FAA requires that certain performance information be provided in the Rotorcraft Flight Manual in order to show compliance to the regulatory requirements. The flight manual, by regulation, must be furnished with each aircraft.

We are superseding Airworthiness Directive (AD) 2014-03-08 for all Airbus Model A318, A319, A320, and A321 series airplanes. AD 2014- 03-08 required an inspection to determine the part number of the interconnecting struts installed on the wings, identifying the part number and the serial number of the associated target and proximity sensor if applicable, and replacing or re-identifying the flap interconnecting strut if applicable. This new AD corrects a typographical error that affects the definition of a serviceable interconnecting strut. This AD was prompted by a report that an investigation showed that when a certain combination of a target/ proximity sensor serial number is installed on a flap interconnecting strut, a ``target FAR'' signal cannot be detected when it reaches the mechanical end stop of the interconnecting strut. We are issuing this AD to detect and correct a latent failure of the flap down drive disconnection due to an already-failed interconnecting strut sensor, which could result in asymmetric flap panel movement and consequent loss of control of the airplane.

We are adopting a new airworthiness directive (AD) for certain Airbus Model A330-200 and -300 series airplanes, and Model A340-200 and -300 series airplanes. This AD requires repetitive inspections of certain sidestay upper cardan pins of the main landing gear (MLG), and associated nuts and retainer assemblies, and pin replacement if necessary. This AD also provides for an optional measurement of the cardan pin clearance dimensions (gap check) and corrective actions if necessary, which would terminate the repetitive inspections. This AD was prompted by a report of a sidestay upper cardan pin of the MLG migrating out of position. We are issuing this AD to detect and correct migration of the sidestay upper cardan pin, which could result in disconnection of the sidestay upper arm from the airplane structure, and could result in a landing gear collapse and consequent damage to the airplane and injury to occupants.

We are superseding Airworthiness Directive (AD) 2009-24-07 for certain the Boeing Company Model 737-600, -700, -700C, and -800 series airplanes. AD 2009-24-07 required repetitive lubrications of the right and left main landing gear (MLG) forward trunnion pins. AD 2009-24-07 also required an inspection for discrepancies of the transition radius of the MLG forward trunnion pins, and corrective actions if necessary. For certain airplanes, AD 2009-24-07 required repetitive detailed inspections for discrepancies (including finish damage, corrosion, pitting, and base metal scratches) of the transition radius of the left and right MLG trunnion pins, and corrective action if necessary. Replacing or overhauling the trunnion pins terminates the actions required by AD 2009-24-07. This new AD adds airplanes to the applicability of AD 2009-24-07. This AD was prompted by reports of corrosion protection damage to the forward trunnion pin on additional airplanes. We are issuing this AD to prevent stress corrosion cracking of the forward trunnion pins, which could result in fracture of the pins and consequent collapse of the MLG.

We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747 airplanes. This AD was prompted by reports of cracking in particular areas of the bulkhead structure at body station (BS) 2598. This AD requires repetitive inspections, including post-repair and post-modification inspections, for cracking in the bulkhead structure at BS 2598; certain one-time inspections of certain fasteners and support frame modifications on certain airplanes; related investigative and corrective actions, if necessary; and an interim modification that would terminate certain repetitive inspections. We are issuing this AD to detect and correct fatigue cracking of the BS 2598 bulkhead structure, which could adversely affect the structural integrity of the bulkhead and the horizontal stabilizer support structure, and result in loss of controllability of the airplane.