Federal Aviation Administration 2014 – Federal Register Recent Federal Regulation Documents

These special conditions are issued for Airbus Model A350-900 series airplanes. These airplanes will have a novel or unusual design feature associated with lateral- directional and longitudinal stability, and low-energy awareness. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

We propose to supersede Airworthiness Directive (AD) 2013-16- 08 for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, and Model CL-600-2D24 (Regional Jet Series 900) airplanes. Since we issued AD 2013-16-08, we have determined that a certain part was incorrectly identified in a certain section of that AD. This proposed AD would continue to require inspection of the MLG retraction actuator components; corrective actions if necessary; and, for certain retraction actuators, installation of a new jam nut. We are proposing this AD to prevent disconnection of the MLG retraction actuator, which could result in extension of the MLG without damping, and consequent structural damage and collapse of the MLG during landing.

These special conditions are issued for the Learjet Inc. Model LJ-200-1A10 airplane. This airplane will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. The fuselage of the Model LJ-200-1A10 will be made of composite materials rather than conventional aluminum, which may affect fire propagation during an in-flight fire. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

We propose to supersede airworthiness directive (AD) 98-07-07, which applies to all Rolls-Royce plc (RR) RB211-535E4 and RB211-535E4-B turbofan engines. AD 98-07-07 requires removing certain part number (P/ N) low-pressure (LP) fuel filter-to-high-pressure (HP) fuel pump tube assemblies and installing flexible LP fuel filter-to-HP fuel pump tube assemblies. Since we issued AD 98-07-07, we received additional reports of fuel leaks that have resulted in a number of engine in-flight shutdowns. This proposed AD would expand the applicability of AD 98-07- 07 to include the RB211-535E4-C-37 turbofan engine. We are proposing this AD to prevent loss of fuel supply to the engine, which could lead to an in-flight shutdown of one or more engines, loss of thrust control, and damage to the airplane.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

We propose to adopt a new airworthiness directive (AD) for certain Sikorsky Model S-92A helicopters. This proposed AD would require installing a main gearbox (MGB) failed pump sensor and vacuum switch wiring, installing an MGB oil auto bypass system, activating Aircraft Management System (AMS) 7.1 software to show a new visual warning, and installing updated enhanced ground proximity warning system (EGPWS) software that includes an aural annunciation of a complete oil pressure loss condition. This proposed AD would also require inserting a Rotorcraft Flight Manual (RFM) Supplement into the applicable RFM. This proposed AD is prompted by investigation results of in-service oil leakage incidents. The proposed actions are intended to alert and prevent MGB oil loss, which could lead to failure of the MGB and subsequent loss of control of the helicopter.

We propose to supersede Airworthiness Directive (AD) 2002-07- 08, which applies to certain The Boeing Company Model 737 airplanes. AD 2002-07-08 currently requires repetitive inspections for cracking of the lower skin at the lower row of fasteners in the lap joints of the fuselage; repair of any cracking found; modification of the fuselage lap joints at certain locations, which terminates the repetitive inspections of the modified areas; and replacement of a certain preventive modification with an improved modification. Since we issued AD 2002-07-08, we have determined that adjacent stringers and window frames have cracked in locations outside the inspection areas addressed by AD 2002-07-08. This proposed AD would add repetitive inspections for cracking at certain window corner fastener holes, a preventive modification, post-repair/alteration and butt joint repetitive inspections, and repair if necessary. We are proposing this AD to detect and correct fatigue cracking of the fuselage lap joints, which could result in reduced structural integrity and sudden decompression of the airplane.

We are adopting a new airworthiness directive (AD) for certain serial number Pratt & Whitney Canada Corporation (P&WC) model PW150A turboprop engines. This AD requires rerouting of the igniter cables and installation of new support brackets. This AD was prompted by reports of damage to a high-pressure fuel line, which could result in a high- pressure fuel leak into the engine nacelle. We are issuing this AD to prevent high-pressure fuel leaks, which could cause engine fire and damage to the engine and the airplane.

We are adopting a new airworthiness directive (AD) for GROB- WERKE GMBH & CO KG Models G102 STANDARD ASTIR III, G102 CLUB ASTIR III, and G102 CLUB ASTIR IIIb gliders and BURKHART GROB LUFTUND RAUMFAHRT GmbH & CO KG Models G103 TWIN II, G103A TWIN II ACRO, G103C TWIN III ACRO, and G 103 C Twin III SL gliders. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as plastic control cable pulleys developing cracks due to aging. We are issuing this AD to require actions to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for certain Airbus Model A320-111, -211, -212, and -231 airplanes. This AD was prompted by reports of broken struts of the center wing box (CWB). This AD requires a detailed inspection of the CWB struts for cracking, and repair if necessary. We are issuing this AD to detect and correct cracked or broken struts, which could result in strut failure and consequent reduced structural integrity of the airplane.

We are superseding Airworthiness Directive (AD) 2013-24-14 for Diamond Aircraft Industries GmbH Models DA40 and DA40F airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the fatigue strength found in the aft main spar not ensuring unlimited lifetime structural integrity. We are issuing this AD to require actions to address the unsafe condition on these products.

The FAA hereby provides notice of intent to release approximately 1.166 acres of airport property at Venice Municipal Airport, Venice, FL, from the conditions, reservations, and restrictions as contained in a Quitclaim Deed agreement between the FAA and the City of Venice, FL, dated June 10, 1947. The release of property will allow the City of Venice to dispose of the property for other than aeronautical purposes. The property is located at 1600 Harbor Drive South. The parcel is currently designated as non- aeronautical land use. The property will be released of its federal obligations for commercial land use. The fair market value of this parcel has been determined to be $2,200,000.

The FAA proposes to amend the collective risk limits for commercial launches and reentries. Under this proposal, the FAA would separate its expected-number-of-casualties (Ec) limits for launches and reentries. For commercial launches, the FAA proposes to aggregate the Ec posed by the following hazards: Impacting inert and explosive debris, toxic release, and far field blast overpressure. The FAA proposes to limit the aggregate Ec for these three hazards to 1 x 10-\4\. For commercial reentries, the FAA proposes to aggregate the Ec posed by debris and toxic release, and set that Ec under an aggregate limit of 1 x 10-\4\. Under the FAA's proposal, the aggregate Ec limit for both launch and reentry would be expressed using only one significant digit. The FAA also proposes to clarify the regulatory requirements concerning hazard areas for ships and aircraft. The proposed rule would require a launch operator to establish a hazard area where the probability of impact does not exceed: 0.000001 (1 x 10-\6\) for an aircraft; and 0.00001 (1 x 10-\5\) for a water-borne- vessel.

We propose to adopt a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This proposed AD was prompted by a determination that more restrictive airworthiness limitations are necessary. This proposed AD would require revising the maintenance or inspection program as applicable. We are proposing this AD to prevent a safety-significant latent failure (which is not annunciated) which, in combination with one or more other specific failures or events, would result in a hazardous or catastrophic failure condition.

We propose to adopt a new airworthiness directive (AD) for all The Boeing Company Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD- 83), DC-9-87 (MD-87), and MD-88 airplanes. This proposed AD was prompted by reports of cracks emanating from the aft-most barrel nut holes of the left and right upper rear spar caps of the horizontal stabilizer. This proposed AD would require repetitive high frequency eddy current (ETHF) inspections for cracks in the areas around the two aft-most barrel nut holes of the upper rear spar caps, and corrective actions if necessary; and repetitive ETHF inspections for cracks in the areas around the two aft-most barrel nut holes of any repaired or replaced upper rear spar cap, and corrective actions if necessary. We are proposing this AD to detect and correct cracks in the horizontal stabilizer, which could propagate until an upper rear spar cap severs, and result in failure of the horizontal stabilizer upper center or aft skin panel and adversely affect the structural integrity of the airplane.

This action establishes Class E airspace at the Truth or Consequences VHF Omni-Directional Radio Range Tactical Air Navigation Aid (VORTAC), Truth or Consequences, NM, to facilitate vectoring of Instrument Flight Rules (IFR) aircraft under control of Albuquerque Air Route Traffic Control Center (ARTCC). This improves the safety and management of IFR operations within the National Airspace System.

We propose to adopt a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400 series airplanes. This proposed AD was prompted by a report of several cracks found on the forward passenger airstair door step assembly. This proposed AD would require an inspection to determine the serial number of the airstair step assembly, and if necessary, an electronic tap test, re-identification of the airstair step assembly, and replacement of the airstair step assembly. We are proposing this AD to detect and correct cracks in the forward passenger airstair door step assembly, which could propagate and result in the structural failure of the steps and impede the evacuation of passengers in the event of an emergency egress situation.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on May 2, 2014, vol. 79, no. 85, page 25172. 14 CFR part 17 sets forth procedures for filing solicitation protests and contract claims in the FAA's Office of Dispute Resolution for Acquisition. The regulations seek factual and legal information from protesters or claimants primarily through written submissions.

The Federal Aviation Administration (FAA) is issuing this notice to advise the public of the availability of the Final Written Reevaluation and Record of Decision for a minor adjustment to a project evaluated in FAA's 2005 Final Environmental Impact Statement (FEIS) for the LAX Master Plan is available for public inspection. The Final Written Reevaluation and Record of Decision was prepared for the construction and operation of the proposed West Aircraft Maintenance Area (WAMA) west of Taxiway AA in the southwest quadrant of Los Angeles International Airport, Los Angeles, California. FAA is making the Final Written Reevaluation and Record of Decision available for public inspection.

We propose to adopt a new airworthiness directive (AD) for all Airbus Model A300 series airplanes; Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes); and Airbus Model A310 series airplanes. This proposed AD was prompted by a report of early ruptures on the levers of the nose landing gear (NLG) sequence valve. This proposed AD would require a one-time inspection for damage of the landing gear sequence valve levers and pin shearing indicating areas on the NLG and the main landing gears (MLGs); and depending on findings, replacing the sequence valve and lever, or doing a one-time inspection to detect interference between control rods and sequence valves and corrective actions if necessary. We are proposing this AD to detect and correct interference between a landing gear leg and door, which could result in failure of that landing gear to extend and could damage the airplane and injure occupants.

We propose to supersede airworthiness directive (AD) 2013-18- 01 for Eurocopter France Model EC 155B, EC155B1, SA-365N, SA-365N1, AS- 365N2, AS-365-N3, and SA-366G1 helicopters. AD 2013-18-01 currently requires inspecting the collective pitch lever for correct locking and unlocking conditions. As published, AD 2013-18-01 contains certain errors. This proposed AD would retain the requirements of AD 2013-18- 01, correct these errors, and update the type certificate holder's name. The proposed actions are intended to detect an incorrectly adjusted collective pitch lever, which could result in loss of control of the helicopter.

This action proposes special conditions for the Bombardier Aerospace, Models BD-500-1A10 and BD-500-1A11 series airplanes. These airplanes will have novel or unusual design features when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. These design features are associated with the composite materials used in the construction of the fuel tank skin and structure, which may behave differently in a post-crash fire than traditional aluminum construction. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

These special conditions are issued for the Embraer S.A. Model EMB-550 airplanes. This airplane will have a novel or unusual design feature associated with electrical and electronic systems that perform critical functions, the loss of which could be catastrophic to the airplane. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

In accordance with National Environmental Policy Act of 1969, as amended (NEPA; 42 United States Code 4321 et seq.), Council on Environmental Quality NEPA implementing regulations (40 Code of Federal Regulations parts 1500 to 1508), and FAA Order 1050.1E, Change 1, Environmental Impacts: Policies and Procedures, the FAA is announcing the availability of the ROD for the SpaceX Texas Launch Site, Cameron County, Texas. The ROD provides the FAA's final environmental determination and approval to support the issuance of launch licenses and/or experimental permits that would allow Space Exploration Technologies Corp. (SpaceX) to launch the Falcon 9 and Falcon Heavy orbital vertical launch vehicles and a variety of reusable suborbital launch vehicles from a launch site on privately owned property in Cameron County, Texas, as proposed in the Final Environmental Impact Statement (EIS) published in May 2014. The ROD provides a description of the applicant's Proposed Action and reasonable alternatives, and identifies the FAA's preferred and the environmentally preferred alternative. It includes a discussion of environmental impacts associated with the Proposed Action in each resource area, as analyzed in the Final EIS. The ROD summarizes the mitigation and enforcement actions that would be made the subject of the terms and conditions of the launch licenses and/or experimental permits issued to SpaceX, as well as other conservation and enhancement measures described in the Final EIS and presented for consideration. The Final EIS, prepared by the FAA for the SpaceX Texas Launch Site, serves as the primary reference and basis for preparation of the ROD. The Final EIS documents the analysis of environmental consequences associated with the construction and operation of the SpaceX Texas Launch Site and the No Action Alternative. The FAA is the lead Federal agency responsible for preparation of the EIS and ROD. Cooperating agencies include the National Aeronautics and Space Administration, National Park Service (NPS), U.S. Army White Sands Missile Range, and U.S. Army Corps of Engineers (USACE). The EIS and ROD were prepared pursuant to the requirements of NEPA, the CEQ Regulations for Implementing the Procedural Provisions of NEPA, and FAA Order 1050.1E, Change 1, Environmental Impacts: Policies and Procedures. The FAA has posted the ROD on the FAA Web site at https:// www.faa.gov/about/officeorg/headquartersoffices/ast/environme ntal/ nepadocs/review/documentsprogress/spacextexaslaunchsite environmentalimpactstatement/.

We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-215-6B11 (CL-215T Variant), and CL- 215-6B11 (CL-415 Variant) airplanes. This proposed AD was prompted by a report that during a routine inspection, corrosion was discovered on the lower bearing of the rudder upper torque tube. This proposed AD would require applying grease to the bearing; doing a general visual inspection of the expelled old grease for any contaminants, metal wear, and indication of corrosion, and replacing the bearing if necessary; revising the maintenance or inspection program, as applicable, to incorporate the rudder spring tab operational test and a check of the rudder spring tab operation into the daily inspection. We are proposing this AD to prevent corroded bearings, which could result in a partial or total loss of axial support.