Federal Aviation Administration February 2018 – Federal Register Recent Federal Regulation Documents

This amendment adopts miscellaneous amendments to the required IFR (instrument flight rules) altitudes and changeover points for certain Federal airways, jet routes, or direct routes for which a minimum or maximum en route authorized IFR altitude is prescribed. This regulatory action is needed because of changes occurring in the National Airspace System. These changes are designed to provide for the safe and efficient use of the navigable airspace under instrument conditions in the affected areas.

The FAA announces the relocation of the FAA Northwest Mountain Regional Office, which issues airworthiness directives (ADs) for transport category airplanes.

We are adopting a new airworthiness directive (AD) for certain AgustaWestland S.p.A. (AgustaWestland) Model AW189 helicopters. This AD requires replacing the seal and filler wedges of all emergency exit windows. This AD was prompted by a report that some windows were improperly glued when installed. The actions of this AD are intended to correct an unsafe condition on these products.

The Federal Aviation Administration (FAA) announces its determination that the noise exposure maps submitted by the City of Fresno for Fresno Yosemite International Airport under the provisions of 49 U.S.C. 47501 et seq. (Aviation Safety and Noise Abatement Act) and 14 CFR part 150 are in compliance with applicable requirements.

The FAA hereby provides notice of intent to release certain airport properties 7.28 acres at the Leesburg International Airport, Leesburg, FL from the conditions, reservations, and restrictions as contained in a Quitclaim Deed agreement between the FAA and the City of Leesburg, dated March 23, 1948. The release of property will allow the City of Leesburg to dispose of the property for other than aeronautical purposes. The property is located north of the airport, across U.S. Highway 441. The parcel is currently designated Non Aeronautical Use. The property will be released of its federal obligations for Commercial Use. The fair market value of this parcel has been determined to be $2,200,000. Documents reflecting the Sponsor's request are available, by appointment only, for inspection at the Leesburg International Airport and the FAA Airports District Office.

This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

We are adopting a new airworthiness directive (AD) for certain Airbus Model A319-112, A319-115, A320-214, A320-232, and A321-211 airplanes. This AD was prompted by in-service experience and further analysis, which showed that the galley 5 without kick-load retainers, was unable to withstand the expected loading during several flight phases or in case of emergency landing. This AD requires modification of galley 5 trolley compartments by adding kick-load retainers. We are issuing this AD to address the unsafe condition on these products.

We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 777-200, -200LR, -300, and -300ER series airplanes. This proposed AD was prompted by reports that additional areas of Boeing Material Specification (BMS) 8-39 flexible urethane foam were found during a routine inspection. This proposed AD would require an inspection for foam insulation on the dripshield above the overhead panel support structure and replacement if necessary. For certain airplanes, this proposed AD would also require replacement of foam insulation on the overhead panel support structure. We are proposing this AD to address the unsafe condition on these products.

This action proposes to remove Class E airspace extending upward from 1,200 feet above the surface at Crows Landing Airport, Crows Landing, CA. This airspace is wholly contained within the Sacramento en route airspace area and duplication is not necessary.

This action proposes to amend Class D airspace, Class E surface airspace, and Class E airspace designated as an extension to a Class D surface area, by updating the name to Erie International Airport/Tom Ridge Field, Erie, PA. This action also proposes to amend Class E airspace extending upward from 700 feet above the surface in Erie, PA, by updating the name to St. Vincent Health Center Heliport. This action also would update the geographic coordinates of the airport and heliport, and would replace the outdated term ``Airport/Facility Directory'' with the term ``Chart Supplement'' in the legal descriptions of associated Class D and E airspace to match the FAA's aeronautical database.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval for a new information collection. The collection involves an internet based tool, the Safety Assurance System (SAS) External Portal. The SAS External Portal is used by the FAA's Office of Flight Standards to conduct initial certification, routine surveillance, and certificate management for applicants and certificate holders. The information to be collected will be used to better facilitate efficient certification, surveillance and certificate management activities.

We propose to adopt a new airworthiness directive (AD) for The Boeing Company Model 787 series airplanes powered by Rolls Royce Trent 1000 engines. This proposed AD was prompted by a report of failures of the inner fixed structure (IFS) forward upper fire seal and damage to thermal insulation blankets in the forward upper area of the thrust reverser (TR). This proposed AD would require an inspection to determine the part number of the IFS forward upper fire seal, and applicable on-condition actions. We are proposing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for certain Fokker Services B.V. Model F28 Mark 0100 airplanes. This AD was prompted by a report that a jammed control cable prevented the full extension of the nose landing gear (LG). This AD requires a general visual inspection of the LG handle teleflex cable conduit connector for the presence of a grease nipple, a maintenance records check of affected airplanes, a detailed inspection for corrosion and damage of the LG handle teleflex cable, and corrective actions if necessary. This AD also requires revising the maintenance or inspection program, as applicable. We are issuing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747- 200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. This AD was prompted by a report of incidents involving fatigue cracking in transport category airplanes that are approaching or have exceeded their design service objective and a structural reevaluation by the manufacturer that identified additional structural elements that qualify as structural significant items (SSIs). This AD requires revising the maintenance or inspection program, as applicable, to include inspections that will give no less than the required damage tolerance rating (DTR) for certain SSI, performing repetitive inspections to detect cracks of all SSIs, and repairing cracked structures if necessary. Additionally, this AD requires all cracks involving an SSI or related structure in close vicinity to the SSI to be reported to Boeing. We are issuing this AD to address the unsafe condition on these products.

Notice is being given that the FAA is considering a proposal from the Great Falls International Airport Authority to change certain portions of the airport from aeronautical use to non-aeronautical use at the Great Falls International Airport, Great Falls, MT. The proposal consists of 2.99 acres acquired with an Airport Improvement Program grant shown on the Airport's Exhibit ``A'' as Parcel 15.

This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This action proposes special conditions for the Boeing Model 747-8 airplane. This airplane, as modified by SWS Certification Services, Ltd. (SWS), will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport-category airplanes. This design feature is the installation of an overhead passenger-sleeping compartment in the main deck. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

We propose to adopt a new airworthiness directive (AD) for all The Boeing Company Model 737-100, -200, -200C, -300, -400, -500 series airplanes. This proposed AD was prompted by reports of cracking in certain flanges, and the adjacent web, of the wing outboard flap track at certain positions. This proposed AD would require an inspection to determine the part number of the wing outboard flap track assembly; repetitive inspections of each affected wing outboard flap track for discrepancies, and applicable on-condition actions; and repetitive overhaul of each wing outboard flap track. We are proposing this AD to address the unsafe condition on these products.

This action proposes to amend Class E surface area airspace and Class E airspace extending upward from 700 feet above the surface at Waimea-Kohala Airport, Kamuela, HI. The part-time Notice to Airmen (NOTAM) status would be removed from Class E surface area airspace, references to the Kamuela VOR/DME would be removed from all associated Class E airspace areas, and airspace boundaries would be modified to only that area necessary to contain instrument flight rules (IFR) operations at the airport. Airspace redesign is necessary as the FAA transitions from ground-based to satellite-based navigation for the safety and management of the national airspace system. Also, an editorial change would be made removing the airport name and replacing it with the city in the airspace designators for the above airspace areas.

This action proposes to amend Class D airspace, Class E surface area airspace, and Class E airspace extending upward from 700 feet above the surface, at Aurora State Airport, Aurora, OR. After a biennial review the FAA found modification necessary to accommodate airspace redesign for the safety and management of instrument flight rules (IFR) operations at the airport. Additionally, an editorial change would be made removing the city associated with the airport name in the airspace designations. Also, this proposal would make an editorial change to the Class D airspace legal description replacing Airport/Facility Directory with the term Chart Supplement.

This action proposes to remove Class E airspace extending upward from 700 feet above the surface at Desert Rock Airport, Mercury, NV. This airspace is not required, as there are no instrument flight rules (IFR) operations at the airport.

The Federal Aviation Administration (FAA) announces its findings on the noise compatibility program submitted by the City of Hawthorne, California. On April 11, 2014, the FAA determined that the noise exposure maps submitted by the City of Hawthorne were in compliance with applicable requirements. On December 18, 2017, the FAA approved the Hawthorne Municipal Airport Noise Compatibility Program. All 11 of the recommendations of the program were approved. No program elements relating to new or revised flight procedures for noise abatement were proposed by the airport operator.

This is notification of criteria used to evaluate the Millennium Engineering and Integration Company (MEI) safety approval application. This Notice publishes the criteria that the FAA used to evaluate the safety approval application pursuant to FAA regulations. Background: MEI applied for, and received, a safety approval for its ability to provide its Flight Analyst Workstation (FAWS) as a component of the process to build flight rules, generate the Mission Data Load (MDL), and verify the MDL prior to loading it onto a launch vehicle's autonomous flight safety unit (AFSU). The FAA issued MEI the safety approval, subject to the provisions of Title 51 U.S.C. Subtitle V, ch. 509, and the orders, rules and regulations issued under it. This Notice is published pursuant to Title 14 Code of Federal Regulations (14 CFR 414.35). MEI may offer FAWS as a component of the process of generating and verifying MDLs for AFSUs to a prospective launch or reentry operator to meet the applicable requirements of 14 CFR 417.123(b), (d), and (e), and Sec. 417.309(h). Criteria Used To Evaluate Safety Approval Application: The performance criteria used to evaluate the FAWS as a component of the process of generating and verifying MDLs for AFSUs included the following FAA regulations, NASA standard, U.S. Air Force manuals or instructions, industry standard, and MEI-developed standards: 14 CFR 417.309(h) Flight Safety System AnalysisSoftware and Firmware and 14 CFR 417.123 Computing Systems and Software. NASA-STD-8719.13C Software Safety Standard. AFSPCMAN 91-710 (v1) Range Safety Policies and Procedures, AFSPCMAN 91-710 (v2) Range Safety User Requirements Manual, Volume 2Flight Safety Requirements, AFSPCMAN 91-712 Launch Safety Software and Computing System Requirements, and 45 SWI 91-701 45th Space Wing Launch Safety Software Management. CMMI-Dev (ML3) Capability Maturity Model Integration. MEI-000071 Configuration Management, MEI-000120 Requirements Development and Management, MEI-000124 Technical Solution, MEI-000149 Agile Software Development Process, and MEI-000125 Verification and Validation.

We are adopting a new airworthiness directive (AD) for Viking Air Limited Models DHC-6-1, DHC-6-100, DHC-6-200, DHC-6-300, and DHC-6- 400 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and address an unsafe condition on an aviation product. The MCAI describes the unsafe condition as aileron cable wear; fouling at the wing root rib, fuselage skin, and wing root rib fairlead; and/or fraying of the cable from the root rib fairlead. We are issuing this AD to require actions to address the unsafe condition on these products.

We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 757 airplanes. This proposed AD was prompted by reports of bolt rotation in the engine drag fitting joint and fasteners heads; an inspection of the fastener holes revealed that cracks were found in the skin on two airplanes. This proposed AD would require repetitive inspections for skin cracking and shim migration at the upper link drag fittings, diagonal brace cracking, and fastener looseness; and applicable on-condition actions. We are proposing this AD to address the unsafe condition on these products.