Federal Aviation Administration September 2005 – Federal Register Recent Federal Regulation Documents
Results 101 - 150 of 191
Airworthiness Directives; Boeing Model 747 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747 airplanes. This AD requires repetitive inspections of the dual side braces (DSBs), underwing midspar fittings, and associated parts; other specified actions; and corrective actions if necessary. This AD also provides an optional terminating action for the inspections and other specified actions. This AD is prompted by reports of corroded, migrated, and rotated bearings for the DSBs in the inboard and outboard struts, a report of a fractured retainer for the eccentric bushing for one of the side links of a DSB, and reports of wear and damage to the underwing midspar fitting on the outboard strut. We are issuing this AD to prevent the loss of a DSB or underwing midspar fitting load path, which could result in the transfer of loads and motion to other areas of a strut, and possible separation of a strut and engine from the airplane during flight.
Airworthiness Directives; Boeing Model 747-400, 747-400D, and 747-400F Series Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Boeing Model 747-400, 747-400D, and 747-400F series airplanes. This proposed AD would require repetitive detailed inspections for damage (degraded finish; missing, lifted, peeling, or blistering paint; or signs of corrosion) of the interior skin in the forward and aft cargo compartments, and corrective actions if necessary. This proposed AD is prompted by reports of skin corrosion on four Boeing Model 747 series airplanes that were delivered between 1995 and 1999. We are proposing this AD to detect and correct corrosion, which can penetrate the thickness of the skin and cause cracking, and result in rapid decompression of the airplane.
Airworthiness Directives; Airbus Model A300 B2 and A300 B4 Series Airplanes; and Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes)
The FAA is revising an earlier NPRM for an airworthiness directive (AD) that applies to certain Airbus airplanes as listed above. The original NPRM would have required repetitively inspecting for cracking in the web of nose rib 7 of the inner flap on the wings, and performing related investigative/corrective actions if necessary. The original NPRM was prompted by reports of cracking in the web of nose rib 7 of the inner flap. This action revises the original NPRM by adding additional inspections for cracking in the web of nose rib 7 of the inner flap on the wings, and revising compliance times for certain airplanes. We are proposing this supplemental NPRM to detect and correct cracking in the web of nose rib 7, which could result in rupture of the attachment fitting between the inner flap and flap track no. 2, and consequent reduced structural integrity of the flap.
Airworthiness Directives; Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747SR, and 747SP Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747- 200C, 747-200F, 747-300, 747SR, and 747SP series airplanes. This AD requires repetitive detailed and ultrasonic inspections of the thrust links of the rear engine mounts for any crack or fracture and corrective actions if necessary. This AD results from the finding of a fractured forward lug of the rear engine mount thrust link on the number one strut. We are issuing this AD to detect and correct cracked or fractured thrust links that could lead to the loss of the load path for the rear engine mount bulkhead and damage to other primary engine mount structure, which could result in the in-flight separation of the engine from the airplane and consequent loss of control of the airplane.
Airworthiness Directives; Raytheon Aircraft Company Model 390 Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Raytheon Aircraft Company (Raytheon) Model 390 airplanes. This AD requires you to replace the rudder pedal arm assemblies used in the rudder control system with parts of improved design. This AD results from reports of cracks found on the rudder pedal arm assemblies. We are issuing this AD to prevent failure of the rudder pedal arm assemblies caused by fatigue cracks. This failure could lead to loss of rudder control, loss of nose gear steering, and loss of toe brakes on the side on which the failure occurs.
Petitions for Exemption; Summary of Petitions Received
Pursuant to FAA's rulemaking provisions governing the application, processing, and disposition of petitions for exemption part 11 of Title 14, Code of Federal Regulations (14 CFR), this notice contains a summary of certain petitions seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of any petition or its final disposition.
Environmental Impact Statement: New Orleans International Airport, New Orleans, LA
The FAA is issuing this notice to advise the public that it is withdrawing its intent to prepare an Environmental Impact Statement (EIS) to consider a proposed taxiway to runway conversion and a new air carrier runway at Louis Armstrong New Orleans International Airport, New Orleans, Louisiana.
Airworthiness Directives; Airbus Model A300 B2 Series Airplanes; Model A300 B4 Series Airplanes; Model A300 B4-600 Series Airplanes; Model A300 B4-600R Series Airplanes; Model F4 600R Series Airplanes; Model A300 C4-605R Variant F Airplanes; and Model A310-200 Series Airplanes; and Model A310-300 Series Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus transport category airplanes. This proposed AD would require replacing the existing cabin altitude indicator in the cabin pressure control panel with a new, improved cabin altitude indicator. This proposed AD is prompted by a report of injuries occurring on in- service airplanes when crewmembers forcibly initiated opening of passenger/crew doors against residual pressure causing the doors to rapidly open. We are proposing this AD to prevent injury to crewmembers, and subsequent damage to the airplane caused by rapid opening of the door.
Airworthiness Directives; Hamburger Flugzeugbau G.m.b.H. Model HFB 320 HANSA Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all Hamburger Flugzeugbau G.m.b.H. Model HFB 320 HANSA airplanes. This proposed AD would require revising the Limitations Section of the Airplane Flight Manual to prohibit operation of the airplane past its designed life limit for the primary structure, which is 15,000 flight hours or 15,000 fight cycles, whichever occurs first; and to require contacting the FAA for approval of analysis that the airplane is safe to continue operation beyond the designed life limit. This proposed AD is prompted by a report that all airplanes in operation might have met or exceeded the designed life limit for the primary structure. We are proposing this AD to prevent continued operation of an airplane beyond its designed life limit for the primary structure, which could result in reduced structural integrity of the airplane.
Airworthiness Directives; Sabreliner Model NA-265, NA-265-20, NA-265-30, NA-265-40, NA-265-50, NA-265-60, NA-265-65, NA-265-70, and NA-265-80 Series Airplanes
The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Sabreliner Model NA-265-40, NA- 265-50, NA-265-60, NA-265-70, and NA-265-80 series airplanes. The existing AD currently requires repetitive inspections for discrepancies in the front and rear spars of the wing in the area of the wing center section, and in the lugs on the rear spar and wing trailing edge panel rib, and corrective actions if necessary. This proposed AD would expand the applicability of the existing AD and require new repetitive inspections for fuel leaks of the front and rear spars of the wing, and for discrepancies in the front and rear spars of the wing in the area of the wing center section, and in the lugs on the rear spar and wing trailing edge panel rib. This proposed AD would also require related investigative and corrective actions, if necessary. This proposed AD results from reports of cracking in the upper and lower flanges of the front and rear spars of the wing near the wing center section, and in the lugs on the rear spar. We are proposing this AD to detect and correct cracking or other discrepancies in these areas, which could result in structural failure of the wing.
Airworthiness Directives; Bombardier Model DHC-8-400 Series Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400 series airplanes. This proposed AD would require an inspection of the laminated shims for cracks, damage, or extrusion between the forward attachment fittings of the horizontal stabilizer and the top rib of the vertical stabilizer; a torque check of the attachment bolts in the attachment fittings of the front, middle, and rear spars; and corrective actions if necessary. This proposed AD results from a report indicating that delaminated shims extruded from the interface between the forward attaching fittings of horizontal stabilizer and the top rib of the vertical stabilizer, and that inadequate torque values of some bolts were found. We are proposing this AD to prevent reduced structural integrity of the horizontal stabilizer, and consequent loss of controllability of the airplane.
Airworthiness Directives; Burkhardt Grob Luft-Und Raumfahrt GmbH & CO KG Model G103 TWIN ASTIR Sailplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all Burkhardt Grob Luft-Und Raumfahrt GmbH & CO KG (Grob) Model G103 TWIN ASTIR sailplanes. This proposed AD would require you to replace the elevator lever, part number (P/N) 103-3521, with a part of improved design, P/N 103-3523. This proposed AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this proposed AD to prevent cracks in the elevator lever, which could cause the elevator lever to fail. This failure could result in loss of control of the sailplane.
Service Difficulty Reports
The Federal Aviation Administration is proposing to withdraw a final rule published on September 15, 2000 that would have amended the reporting requirements for certificate holders concerning failures, malfunctions, and defects of aircraft, aircraft engines, systems, and components. The effective date of this final rule has been delayed several times and is now January 31, 2006. We are proposing to withdraw this rule to allow the FAA time to re-examine the service difficulty report (SDR) program based on comments received and other developments since the final rule was published. We are also proposing several amendments that improve the existing SDR program because they did not receive significant comment when proposed in the final rule.
Airworthiness Directives; Aerospatiale Model ATR42-500 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Aerospatiale Model ATR42-500 airplanes. This AD requires inspecting for correct installation of the fastener that attaches the ground braids on the elevator, modifying the forward bonded assembly of the elevator control rod, and corrective action if necessary. This AD results from a functional test of the elevator trim tab control rod of the leading edge, which showed that, in a full-up elevator condition with the tab fully down, interference could occur between the tab control rod and the forward edge of the lower skin of the elevator. We are issuing this AD to prevent discrepancies between the elevator trim tab control rod and the forward edge of the lower skin of the elevator, which could result in reduced control of the elevator and consequent reduced controllability of the airplane.
Airworthiness Directives; Airbus Model A340-200 and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A340-200 and -300 series airplanes. This AD requires revising the airplane flight manual to incorporate new procedures for the flightcrew to follow to correct miscalculation of the takeoff and accelerating or stopping distance of the airplane during a ferry flight under certain conditions. This AD results from a report that a software error could result in a miscalculation (underestimation) of the runway length necessary for takeoff in the case of a ferry flight with one engine not operating. We are issuing this AD to prevent this miscalculation, which, if combined with high takeoff weight, too-short runway length, and high altitude and temperature of the airport, could result in inability of the flightcrew to abort the takeoff in a safe manner, reduced controllability of the airplane, and runway overrun.
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all EMBRAER Model ERJ 170 airplanes. This AD requires inspecting the hydraulic pressure tubes at the outlet of the engine-driven hydraulic pumps to determine the part and serial numbers; and replacing hydraulic pressure tubes having certain serial numbers with new hydraulic pressure tubes. This AD results from failure of a hydraulic system due to leakage of hydraulic fluid from a crack in the pipe coming from the pressure side of the engine-driven pump. We are issuing this AD to prevent cracking of the hydraulic pressure pipes, which could result in failure of hydraulic system 1 or 2 or both, and consequent reduced controllability of the airplane.
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-110P1 and EMB-110P2 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all EMBRAER Model EMB-110P1 and EMB-110P2 airplanes. This AD requires repetitive inspections for corrosion or cracking of the rotating cylinder assembly in the nose landing gear (NLG), and related investigative/corrective actions if necessary. This AD also requires the eventual replacement of the rotating cylinder assembly with a new part, which terminates the need for the repetitive inspections. This AD results from reports of corrosion on the NLG rotating cylinder assembly. We are issuing this AD to prevent cracks from emanating from corrosion pits in the NLG rotating cylinder assembly, which could result in failure of the NLG.
Airworthiness Directives; Boeing Model 777-200 and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 777-200 and -300 series airplanes. This AD requires modification of the splice plate assemblies installed under the floor panels at the forward and aft edges of the cabin aisle. This AD results from reports of cracking of the aluminum splice plates under the floor panels in the cabin aisle. We are issuing this AD to prevent loss of the capability of the cabin floor and seat track structure to support the airplane interior inertia loads under emergency landing conditions. Loss of this support could lead to galley or seat separation from attached restraints, which could result in blocking of the emergency exits and consequent injury to passengers and crew.
Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800, and -900 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Boeing Model 737-600, -700, -700C, -800, and -900 series airplanes. That AD currently requires either determining exposure to runway deicing fluids containing potassium formate, or performing repetitive inspections of certain electrical connectors in the wheel well of the main landing gear (MLG) for corrosion, and follow-on actions. This new AD adds a new inspection requirement and related corrective actions. This AD is prompted by additional reports indicating that significant corrosion of the electrical connectors in the wheel well of the MLG has also been found on airplanes that land on runways treated with deicing fluids containing potassium acetate. We are issuing this AD to prevent corrosion and subsequent moisture ingress into the electrical connectors, which could result in an electrical short and consequent incorrect functioning of critical airplane systems essential to safe flight and landing of the airplane, including fire warning systems.
Establishment of Class E5 Airspace; Gardner, KS
This rule establishes a Class E surface area airspace area extending upward from 700 feet above the surface at Gardner, KS. The effect of this rule is to provide appropriate controlled Class E airspace for aircraft departing from and executing approach procedures to, Gardner Municipal Airport, KS and to segregate aircraft using instrument approach procedures in instrument conditions from aircraft operating in visual conditions.
Modification of Class E Airspace; Norfolk, NE; Correction
This action corrects a direct final rule; request for comments that was published in the Federal Register on Friday, July 29, 2005, (70 FR 43745) [FR Doc. 05-21872].
Modification of Class E Airspace; Lincoln, NE
This action corrects a direct final rule; request for comments that was published in the Federal Register on Friday, July 29, 2005 (70 FR 43741) [FR Doc. 05-21707].
RTCA Special Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems Airborne Equipment
The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 147: Minimum Operational Performance Standards for Traffic Alert and Collision Avoidance Systems Airborne Equipment.
Establishment of Class E Airspace; Golovin, AK
This action establishes Class E airspace at Golovin, AK to provide adequate controlled airspace to contain aircraft executing two new Standard Instrument Approach Procedures (SIAPs) and one new departure procedure. This rule results in new Class E airspace upward from 700 feet (ft.) and 1,200 ft. above the surface at Golovin, AK.
Revision of Class E Airspace; Cordova, AK
This action revises Class E airspace at Cordova, AK to provide adequate controlled airspace to contain aircraft executing new and revised Standard Instrument Approach Procedures (SIAPs). This rule results in a revised Class E surface area and Class E airspace upward from 700 feet (ft.) and 1,200 ft. above the surface at Cordova, AK.
Revision of Class E Airspace; Prospect Creek, AK
This action revises Class E airspace at Prospect Creek, AK to provide adequate controlled airspace to contain aircraft executing Special Instrument Approach Procedures (SIAPs). This rule results in revised Class E airspace upward from 700 feet (ft.) above the surface at Prospect Creek, AK.
Availability of Changes to Advisory Circular 27-1B, Certification of Normal Category Rotorcraft, and Advisory Circular 29-2C, Certification of Transport Category Rotorcraft
This notice announces the availability of changes to AC 27-1B, Certification of Normal Category Rotorcraft, and AC 29-2C, Certification of Transport Category Rotorcraft for AC paragraphs 27.351 and AC 29.351B, Yawing Conditions. These AC paragraphs are final and replace the existing AC paragraphs dated 9/30/99. These AC paragraphs will be included in the upcoming Change 2 update.
Noise Exposure Map Notice
The Federal Aviation Administration (FAA) announces its determination that the noise exposure maps submitted by the City of Dayton for the Dayton International Airport under the provisions of 49 U.S.C. 47501 et seq. Aviation Safety and Noise Abatement Act) and 14 CFR part 150 are in compliance with applicable requirements.
Establishment of Class E Airspace; Chehalis, WA
This final rule will establish Class E airspace at Chehalis, WA. This additional Class E airspace is necessary to accommodate the new Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedure (SIAP) at Chehalis-Centralia Airport. This change will improve the safety of Instrument Flight rules (IFR) aircraft executing the new RNAV GPS SIAP at Chehalis-Centralia Airport, Chelialis, WA.
Aviation Financing Reauthorization
The current taxes and fees paid into the Aviation Trust Fund, which provide funding for the National Aviation System, are only authorized through September 30, 2007. Since there is only a small and declining balance in the Trust Fund, it is critical that the financing not be allowed to lapse. The new financing structure should generate stable and predictable revenue, maintain the appropriate levels of service, and enable FAA to make long-term investments and tie revenues raised for the system to the infrastructure and operational costs of the system. The FAA has developed a series of data packages in examining FAA costs, paid for through the Trust Fund, from a managerial reporting standpoint. These packages will advance everyone's understanding of FAA costs and what the Agency faces as it considers a range of future funding options. They are available at https:// www.faa.gov/about /officeorg/ headquartersoffices/aep/aatf/.
Airworthiness Directives; BAe Systems (Operations) Limited Model ATP Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all BAe Systems (Operations) Limited Model ATP airplanes. That AD currently requires revising the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness to incorporate life limits for certain items and inspections to detect fatigue cracking in certain structures. This new AD requires a revision to the ALS of the Instructions for Continued Airworthiness to incorporate new inspections to detect fatigue cracking of certain significant structural items (SSIs) and to revise life limits for certain equipment and various components. This AD is prompted by a determination that existing inspection techniques are not adequate for certain SSIs and by the revision of certain life limits. We are issuing this AD to detect and correct fatigue cracking of certain structural elements, which could adversely affect the structural integrity of these airplanes.
Airworthiness Directives; Raytheon Aircraft Company Models 1900, 1900C, 1900C (C-12J), and 1900D Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Raytheon Aircraft Company Models 1900, 1900C, 1900C (C-12J), and 1900D airplanes. This AD requires you to inspect all elevator hinge support attachments on both left and right elevators for loose and missing rivets, replace rivets if loose or missing rivets are found, inspect the elevator hinge joints for looseness and clearance of each elevator to its stabilizer, correct looseness and clearance if incorrect, and report results of the required inspections. This AD results from a report of excessive movement of the elevator and elevator trim. The hinge support attachment that attaches the elevator to the horizontal stabilizer was loose and had loose and missing rivets. The elevator counterweight horn showed evidence of rubbing against the horizontal stabilizer, indicating possible incorrect clearance. We are issuing this AD to detect and correct any looseness in the elevator hinge support attachments, which could result in binding of the elevator control system. This elevator binding could lead to loss of control of the airplane.
Airworthiness Directives; Raytheon Aircraft Company Model 390 Premier 1 Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Raytheon Aircraft Company (Raytheon) Premier 1 390 airplanes. This AD requires you to verify minimum clearances to correct chafing conditions in the powerplant left-hand and right-hand engine installations. This AD results from reports of inadequate left-hand and right-hand engine assembly cable, wire, and hose routing clearance. We are issuing this AD to detect and correct chafing conditions in the engine installation, which could result in leaking flammable fluids near an ignition source. This failure could lead to fire damage or loss of airplane control.
Public Notice for Waiver of Aeronautical Land-Use Assurance Bolton Field Airport, Columbus, OH
The Federal Aviation Administration (FAA) is considering a proposal to change a portion of the airport designated aeronautical use to non-aeronautical use and to authorize the release of 1.5411 acres of airport property for an exchange of property between the Columbus Regional Airport Authority (CRAA) and the City of Columbus. The land currently houses a fire station that will remain on the site. The land was conveyed to the City of Columbus in Deed Volume 2806, page 644 of the Recorder's Office, Franklin County, Ohio. The land was acquired by the City of Columbus with funding from Federal Grant 8-39-0026-01. There are no impacts to the airport by allowing the airport to dispose of the property. Approval does not constitute a commitment by the FAA to financially assist in the disposal of the subject airport property nor a determination of eligibility for grant-in-aid funding from the FAA. In exchange, the CRAA will receive a parcel of land (43.562 acres) currently being used as a golf course facility adjacent to Port Columbus International Airport. This parcel is partially located in the existing Runway Protection Zone for Runway 10R-28L and is partially located in the Runway Protection Zone for future Runway 10R-28L as indicated on the approved Airport Layout Plan (ALP) for Port Columbus International Airport. In accordance with section 47107(h) of title 49, United States Code, this notice is required to be published in the Federal Register 30 days before modifying the land-use assurance that requires the property to be used for an aeronautical purpose.
Airworthiness Directives; Airbus Model A300 B2 Series Airplanes, Model A300 B4 Series Airplanes, Model A310-200 Series Airplanes, Model A310-300 Series Airplanes, and Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes)
The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus transport category airplanes. This proposed AD would require repetitive eddy current inspections for cracks of the stiffener fittings of the fuselage at frame (FR) 12A, and corrective actions if necessary. This proposed AD also provides a terminating action for the inspections. This proposed AD results from reports of cracks on the upper attachment fitting of the stiffener fitting at FR12A. We are proposing this AD to prevent failure of the stiffener fittings, which could result in the reduced structural integrity of the floor and rods around FR12A.
Airworthiness Directives; Boeing Model 747-100B SUD, 747-200B, 747-300, 747-400, and 747-400D Series Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Boeing Model 747-100B SUD, 747-300, 747-400, and 747-400D series airplanes; and Model 747-200B series airplanes having a stretched upper deck. This proposed AD would require repetitively inspecting for cracking or discrepancies of the fasteners in the tension ties, shear webs, and frames at body stations 1120 through 1220, and related investigative and corrective actions if necessary. This proposed AD results from new reports of severed tension ties, as well as numerous reports of cracked tension ties, broken fasteners, and cracks in the frame, shear web, and shear ties adjacent to tension ties for the upper deck. We are proposing this AD to detect and correct cracking of the tension ties, shear webs, and frames of the upper deck, which could result in rapid decompression of the airplane.
Airworthiness Directives; Rolls-Royce plc RB211 Trent 875, 877, 884, 884B, 892, 892B, and 895 Series Turbofan Engines
The FAA is revising an existing airworthiness directive (AD) for Rolls-Royce plc (RR) RB211 Trent 875, 877, 884, 884B, 892, 892B, and 895 series turbofan engines with certain part number (P/N) low pressure compressor (LPC) fan blades installed. That AD currently requires initial and repetitive ultrasonic inspections of the fan blade dovetail roots and defines a specific terminating action to the repetitive blade inspection requirements. This AD requires the same actions but clarifies the terminating action. We are issuing this AD to prevent multiple LPC fan blade failures due to cracks, which could result in uncontained engine failure and possible damage to the airplane.
Petitions for Exemption; Dispositions of Petitions Issued
Pursuant to FAA's rulemaking provisions governing the application, processing, and disposition of petitions for exemption, part 11 of Title 14, Code of Federal Regulations (14 CFR), this notice contains the disposition of certain petitions previously received. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of any petition or its final disposition.
Petitions for Exemption; Summary of Petitions Received
Pursuant to FAA's rulemaking provisions governing the application, processing, and disposition of petitions for exemption part 11 of Title 14, Code of Federal Regulations (14 CFR), this notice contains a summary of certain petitions seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of any petition or its final disposition.
Second-in-Command Pilot Type Rating
The FAA is establishing a compliance date for the final rule published in the Federal Register on August 4, 2005. The rule revised the pilot certification regulations to establish a second-in-command (SIC) pilot type rating and associated qualifying procedures. This action is necessary to give affected pilots time to prepare and file the paperwork necessary to obtain the SIC pilot type rating. We also are correcting the amendment number of the final rule.
Airworthiness Directives; Engine Components Inc. (ECi) Reciprocating Engine Cylinder Assemblies
The FAA proposes to adopt a new airworthiness directive (AD) for Lycoming Engines (formerly Textron Lycoming) models 320, 360, and 540 series, ``Parallel Valve'' reciprocating engines, with certain Engine Components Inc. (ECi) cylinder assemblies, part number (P/N) AEL65102 series ``Classic Cast,'' installed. This proposed AD would require replacing these ECi cylinder assemblies. This proposed AD results from reports of about 30 failures of the subject cylinder assemblies marketed by ECi. We are proposing this AD to prevent loss of engine power due to cracks in the cylinder assemblies and possible engine failure caused by separation of a cylinder head.
Proposed Establishment of Class E Airspace; Nikolai, AK
This action proposes to establish Class E airspace at Nikolai, AK to the size necessary to contain aircraft executing Standard Instrument Approach Procedures (SIAP). This action is proposed as a result of the development of two new SIAPs. Adoption of this proposal would result in establishing Class E airspace upward from 700 feet (ft.) above the surface at Nikolai, Alaska.
Proposed Revision of Class E Airspace; Nenana, AK
This action proposes to revise Class E airspace at Nenana Municipal Airport, AK to the size necessary to contain aircraft executing Standard Instrument Approach Procedures (SIAP) and a Departure Procedure (DP). This action is needed as a result of runway renumbering due to changes in magnetic variation. Adoption of this proposal would result in revising Class E airspace upward from 700 feet (ft.) above the surface at Nenana Municipal Airport, Alaska.
Proposed Revision of Class E Airspace; Egegik, AK
This action proposes to revise Class E airspace at Egegik, AK to the size necessary to contain aircraft executing Standard Instrument Approach Procedures (SIAP). Adoption of this proposal would result in revising Class E airspace upward from 700 feet (ft.) above the surface at Egegik, Alaska.
Proposed Establishment of Class E Airspace; Arctic Village, AK
This action proposes to establish Class E airspace at Arctic Village, AK to the size necessary to contain aircraft executing two new Standard Instrument Approach Procedures (SIAP) and an Instrument Flight Rules (IFR) departure procedure. Adoption of this proposal would result in establishing Class E airspace upward from 700 feet (ft.) above the surface and from 1,200 ft. above the surface at Arctic Village, Alaska.
State Court Decision Affecting Recordation of Artisan Liens
Consistent with Agency policy, the Federal Aviation Administration (FAA) gives notice of the holding in Creation Aviation, Inc., vs. Textron Financial Corporation, Florida District Court of Appeal, Fourth District, No. 4D04-2178, decided on April 27, 2005. The Court in Creston held that Federal law pertaining to recording with the FAA Aircraft Registry did not preempt a Florida statute requiring that an artisan lien for work on an aircraft first be filed in the county where the work was performed in order to enforce the lien under Florida law. Accordingly, the FAA is advising the public that recording an artisan lien with the FAA Aircraft Registry only, may be insufficient to enforce an artisan lien under Florida law.
Modification of Class D and Class E Airspace; Salina Municipal Airport, KS
This action corrects an error in the legal description of Class D airspace in a direct final rule, request for comments that was published in the Federal Register on Friday July 29, 2005 (70 FR 43742).
Airworthiness Directives; Bombardier Model DHC-8-400 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400 series airplanes. This AD requires a one-time inspection of the fuel and hydraulic tubes, and corrective actions if necessary. This AD also requires modifying fairlead plate assemblies. This AD results from reports of chafing between fuel and hydraulic tubes and the fairlead plate where the tubes pass through the firewall. We are issuing this AD to prevent chafing of the fuel and hydraulic tubes, which could lead to fuel and/or hydraulic fluid leakage in the engine nacelle area and consequent fire or explosion.
Airworthiness Directives; Goodrich De-icing and Specialty Systems “FASTprop” Propeller De-icers
The FAA is adopting a new airworthiness directive (AD) for Goodrich De-icing and Specialty Systems ``FASTprop'' propeller de- icers, part numbers P4E1188 series, P4E1601 series, P4E2200 series, P4E2271-10, P4E2575-7, P4E2575-10, P4E2598-10, P5855BSW, P6199SW, P6592SW, P6662SW, and P6975-11, installed. This AD requires inspection, repair, or replacement of those ``FASTprop'' propeller de-icers that fail daily visual checks. This AD results from reports of Goodrich ``FASTprop'' propeller de-icers becoming loose or debonded, and detaching from propeller blades during operation.
Airworthiness Directives; Boeing Model 757 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 757 airplanes. This AD requires inspections of certain wire bundles in the left and right engine-to-wing aft fairings for discrepancies; installation of back-to-back p-clamps between the wire and hydraulic supply tube at the aft end of the right-hand strut only; and associated re-routing of the wire bundles, if necessary. This AD results from a report indicating that a circuit breaker for the fuel shutoff valve tripped due to a wire that chafed against the structure in the flammable leakage zone of the aft fairing, causing a short circuit. We are issuing this AD to prevent chafing between the wire bundle and the structure of the aft fairing, which could result in electrical arcing and subsequent ignition of flammable vapors and possible uncontrollable fire.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.