Department of Transportation September 2022 – Federal Register Recent Federal Regulation Documents
Results 151 - 200 of 228
Airworthiness Directives; Airbus SAS Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A321-251N, A321-251NX, A321-252N, A321-252NX, A321-253N, and A321-253NX airplanes. This proposed AD was prompted by a stress analysis on the engine structure that indicated that the fail- safe lug may not be able to sustain, during one inspection interval as currently specified in an airworthiness limitations item, the loads deriving from the engagement of the secondary load path within that inspection interval for the aft engine mount system. This proposed AD would require repetitive detailed inspections of the aft engine mount and secondary load path clearance fail-safe pin and replacement of the engine if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products.
Hazardous Materials: Compatibility With the Regulations of the International Atomic Energy Agency
PHMSA, in coordination with the Nuclear Regulatory Commission, proposes to amend the Hazardous Materials Regulations to maintain alignment with international regulations and standards governing the transportation of Class 7 radioactive materials. Specifically, PHMSA proposes to adopt changes contained in the International Atomic Energy Agency standards. Additionally, PHMSA proposes regulatory amendments identified through internal regulatory review processes to update, clarify, correct, or streamline certain regulatory requirements applicable to the transportation of Class 7 (radioactive) materials.
Hours of Service of Drivers: Truck Renting and Leasing Association, Inc. (TRALA); Application for Exemption Renewal
FMCSA announces its decision to provisionally renew the Truck Renting and Leasing Association, Inc. (TRALA) exemption from the provisions that require a motor carrier to install and require each of its drivers to use an electronic logging device (ELD) to record the driver's hours-of-service (HOS). The exemption allows drivers of property carrying commercial motor vehicles (CMVs) rented for 8 days or less, regardless of reason, to not use an ELD in the vehicle. These drivers remain subject to the standard HOS limits and must maintain a paper record of duty status (RODS) if required. The exemption renewal is for 5 years.
Lithium Battery Air Safety Advisory Committee; Notice of Public Meeting
This notice announces a meeting of the Lithium Battery Air Safety Advisory Committee (Committee).
Proposed Agency Information Collection Activities; Comment Request
Under the Paperwork Reduction Act of 1995 (PRA) and its implementing regulations, this notice announces that FRA is forwarding the Information Collection Request (ICR) abstracted below to the Office of Management and Budget (OMB) for review and comment. The ICR describes the information collection and its expected burden. On April 28, 2022, FRA published a notice providing a 60-day period for public comment on the ICR.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This proposed AD was prompted by reports of missing shims, a wrong type of shims, shanked fasteners, fastener head gaps, and incorrect hole sizes common to the left and right side at a certain station (STA) frame inner chord and web. This proposed AD would require inspecting for existing repairs, inspecting the area for cracking, and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; De Havilland Aircraft of Canada Limited (Type Certificate Previously Held by Bombardier, Inc.) Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain De Havilland Aircraft of Canada Limited Model DHC-8-400 series airplanes. This proposed AD was prompted by a report that electrical bonding jumpers had been installed on fuel scavenge lines even after the removal was required by previous AD rulemaking and that electrical bonding jumpers may have been installed in production or in service at other locations. This proposed AD would require an inspection for electrical bonding jumpers and brackets on the fuel scavenge and vent lines at specific wing locations, and if installed, removal or modification of those jumpers and brackets. This proposed AD would also require a records check to determine if certain maintenance tasks were performed and removal, modification, or rework if those tasks were performed. This proposed AD would also prohibit the use of earlier versions of certain maintenance tasks. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; General Electric Company Turbofan Engines
The FAA proposes to adopt a new airworthiness directive (AD) for certain General Electric Company (GE) GE90-90B, GE90-94B, GE90- 110B1, and GE90-115B model turbofan engines. This proposed AD was prompted by a manufacturer investigation that revealed that certain high-pressure turbine (HPT) stage 1 disks, HPT stage 2 disks, and stages 7-9 compressor rotor spools were manufactured from powder metal material suspected to contain iron inclusion. This proposed AD would require the replacement of the affected HPT stage 1 disks, HPT stage 2 disks, and stages 7-9 compressor rotor spools. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; General Electric Company Turbofan Engines
The FAA proposes to adopt a new airworthiness directive (AD) for certain General Electric Company (GE) GEnx-1B and GEnx-2B model turbofan engines. This proposed AD was prompted by a manufacturer investigation that revealed that certain high-pressure turbine (HPT) stage 2 disks, forward seals, and stages 6-10 compressor rotor spools were manufactured from powder metal material suspected to contain iron inclusion. This proposed AD would require the replacement of the affected HPT stage 2 disks, forward seals, and stages 6-10 compressor rotor spools. The FAA is proposing this AD to address the unsafe condition on these products.
Notice of Opportunity for Public Comment on a Proposed Change of Airport Property Land Use From Aeronautical to Non-Aeronautical Use at Bill and Hillary Clinton National Airport, Little Rock, AR
The FAA is considering a request from the City of Little Rock- Little Rock Airport Commission to change approximately 21.29 acres, located on the south side of the airport bordered by Grundfest Drive and East Roosevelt Road, from aeronautical use to non-aeronautical use and to authorize the conversion of the airport property.
Cybersecurity Best Practices for the Safety of Modern Vehicles
On January 12, 2021, NHTSA released its draft Cybersecurity Best Practices for the Safety of Modern Vehicles guidance (``Draft Best Practices'' or ``guidance'') in an effort to support industry-led efforts to improve the industry's cybersecurity posture as well as provide NHTSA's views on how the automotive industry can develop and apply sound, risk-based cybersecurity management processes during the vehicle's entire lifecycle. These guidelines are intended to be applicable to all individuals and organizations involved in the design, development, manufacture and assembly of a motor vehicle and its electronic systems and software. These entities include, but are not limited to, small and large-volume motor vehicle and motor vehicle equipment designers, suppliers, manufacturers, and modifiers. This document summarizes comments received in response to the draft guidance, responds to those comments, and describes changes made to the draft guidance in response to those comments. This document also announces the issuance of the final version of the Cybersecurity Best Practices for the Safety of Modern Vehicles guidance. While this is the final version of this iteration of the Best Practices, NHTSA routinely assesses cybersecurity risks as well as emerging best practices and will consider future updates as motor vehicles and their cybersecurity evolve.
Baby Trend, Inc., Receipt of Petition for Decision of Inconsequential Noncompliance
Baby Trend, Inc., (BT), has determined that certain BT Hybrid 3-in-1 Combination Booster Seat child restraint systems (CRSs) do not fully comply with Federal Motor Vehicle Safety Standard (FMVSS) No. 213, Child Restraint Systems. BT filed an original noncompliance report dated July 6, 2022. BT subsequently petitioned NHTSA on August 1, 2022, for a decision that the subject noncompliance is inconsequential as it relates to motor vehicle safety. This document announces receipt of BT's petition.
Hercules Tire & Rubber Company, Receipt of Petition for Decision of Inconsequential Noncompliance
Hercules Tire & Rubber Company, (Hercules), has determined that certain Ironman iMOVE PT specialty trailer tires do not fully comply with Federal Motor Vehicle Safety Standard (FMVSS) No. 139, New Pneumatic Radial Tires for Light Vehicles. Hercules filed an original noncompliance report dated May 10, 2022, and amended the report on May 12, 2022. Hercules petitioned NHTSA on June 21, 2022, for a decision that the subject noncompliance is inconsequential as it relates to motor vehicle safety. This document announces receipt of Hercules's petition.
Organization Designation Authorizations for Transport Airplanes Expert Review Panel Membership
The FAA is publishing this notice to solicit nominations for membership on the ODA for Transport Airplanes Expert Review Panel (``Review Panel'').
Airworthiness Directives; Airbus SAS Airplanes
The FAA is superseding Emergency Airworthiness Directive (AD) 2022-18-51, which applied to all Airbus SAS Model A330-841 and -941 airplanes. Emergency AD 2022-18-51 required revising the existing airplane flight manual (AFM) to incorporate additional limitations prohibiting takeoff for certain airplane configurations; specified airplane dispatch restrictions using certain provisions of the A330 master minimum equipment list (MMEL) or amending the existing FAA- approved operator's minimum equipment list (MEL); and required obtaining and accomplishing instructions following certain maintenance messages. Since the FAA issued Emergency AD 2022-18-51, additional instructions and maintenance procedures have been developed to address failures of the high pressure valve (HPV). This AD continues to require the actions specified in Emergency AD 2022-18-51, and also requires maintenance actions, including an HPV seal integrity test, repetitive replacement of the HPV clips, revision of the existing AFM, and implementation of updates to the FAA-approved operator's MEL, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Agency Information Collection Activities; Renewal of an Approved Information Collection: Transportation of Hazardous Materials; Highway Routing
In accordance with the Paperwork Reduction Act of 1995, FMCSA announces its plan to submit the Information Collection Request (ICR) described below to the Office of Management and Budget (OMB) for its review and approval and invites public comment. FMCSA requests approval to renew an ICR titled, ``Transportation of Hazardous Materials, Highway Routing.'' The information reported by States and Indian tribes is necessary to identify designated/restricted routes and restrictions or limitations affecting how motor carriers may transport certain hazardous materials on highways, including dates that such routes were established and information on subsequent changes or new hazardous materials routing designations.
Risk Reduction Program
In response to issues raised by a petition for reconsideration of the Risk Reduction Program (RRP) final rule, FRA is issuing this NPRM to solicit information to help determine whether FRA should retain or remove a provision in the RRP final rule clarifying that contractors who perform a significant portion of a railroad's operations are considered the railroad's directly affected employees for purposes of the RRP rule.
Agency Information Collection Activities; Renewal of an Approved Information Collection: 391.41 CMV Driver Medication Form
In accordance with the Paperwork Reduction Act of 1995, FMCSA announces its plan to submit the renewal Information Collection Request (ICR) described below to the Office of Management and Budget (OMB) for review and approval and invites public comment. FMCSA requests approval to renew an ICR titled, ``391.41 CMV Driver Medication Form.'' This Information Collection (IC) is voluntary and may be utilized by Medical Examiners (MEs) responsible for issuing Medical Examiner's Certificates (MECs) to commercial motor vehicle (CMV) drivers. MEs that choose to use this IC do so to communicate with treating healthcare professionals who are responsible for prescribing certain medications, so that the ME fully understands the reasons the medications have been prescribed. The information obtained by the ME when utilizing this IC assists the ME in determining if the driver is medically qualified and ensures that there are no disqualifying medical conditions or underlying medical conditions and prescribed medications that could adversely affect their safe driving ability or cause incapacitation constituting a risk to the public.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A350-941 airplanes. This AD was prompted by a report indicating that the inflatable free aisle restrictor (IFAR) on certain single lane slide-rafts demonstrated inconsistent release behavior in aft wind conditions. This AD requires replacing an affected part with a serviceable part, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also prohibits the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to supersede Airworthiness Directive (AD) 2021-07-09, which applies to all The Boeing Company Model 747-100, 747- 100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. AD 2021-07-09 requires repetitively inspecting all trim air diffuser ducts or sidewall riser duct assemblies (collectively referred to as TADDs) for damage, including repetitive structural inspections of the center fuel tanks for damage, and applicable on-condition actions. Since the FAA issued AD 2021-07-09, the agency has determined that the existing requirements do not adequately address the unsafe condition. This proposed AD would continue to require repetitive inspections of the TADDs for damage with revised compliance times, and repair if applicable. This proposed AD would also require repetitive replacement of the TADDs and would remove the structural inspections of the center fuel tanks. This proposed AD would also prohibit the installation of affected parts. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747- 200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. This proposed AD was prompted by reports that high temperature composite trim air diffuser ducts (TADD) showed composite degradation and signs of hot air leakage. This proposed AD would require a one-time low frequency eddy current (LFEC) inspection of certain center tank upper skin panels on the right and left side for any structural damage due to heat exposure, and repair if necessary. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This proposed AD was prompted by a report indicating that a crack was found in one of the holes of the wing rear spar lower chord at the main landing gear (MLG) aft fitting at a certain wing buttock line (WBL). This proposed AD would require repetitive open hole high frequency eddy current (HFEC) inspections or surface HFEC and ultrasonic (UT) inspections for cracking of the wing rear spar lower chord at the MLG aft fitting at a certain WBL, and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Gulfstream Aerospace Corporation Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Gulfstream Aerospace Corporation Model GVII-G500 and GVII- G600 airplanes. This proposed AD was prompted by reports of two landing incidents in which the alpha limiter engaged in the landing flare in unstable air, resulting in high rate of descent landings and damage to the airplanes. This proposed AD would require updating the flight control computer (FCC) software. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model AS332C, AS332C1, AS332L, and AS332L1 helicopters. This AD was prompted by review of maintenance instructions that showed conflicting methods of recording torque cycles for certain parts. This AD requires recalculating the torque cycles of certain parts and updating log cards; removing certain other parts from service; and applying an operational restriction on certain parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also requires incorporating the re-calculated life limits into existing maintenance records. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 747-8 and -8F series airplanes. This proposed AD was prompted by reports of cracking in stringers and splice fittings located at stringer splices at multiple body stations. This proposed AD would require an inspection of each free flange of the stringers at the stringer splice for the presence of radius fillers at fastener locations, an inspection for cracking of the stringers and stringer splice fittings at certain stringer splice locations, and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Airspace Designations; Incorporation by Reference
This action amends 14 CFR part 71 relating to airspace designations to reflect the approval by the Director of the Federal Register of the incorporation by reference of FAA Order JO 7400.11G, Airspace Designations and Reporting Points. This action also explains the procedures the FAA will use to amend the listings of Class A, B, C, D, and E airspace areas; air traffic service routes; and reporting points incorporated by reference.
Amendment and Revocation of Area Navigation (RNAV) Routes; Southeastern and Northeastern United States
This action amends Area Navigation (RNAV) route Q-81 to realign a portion of the route to improve traffic flows, and to remove Canadian RNAV route Q-947 at the request of NavCanada. These changes support the Northeast Corridor Atlantic Coast Route Project.
Removal of VOR Federal Airways in the Eastern United States
This action removes VHF Omnidirectional Range (VOR) Federal Airways V-31, V-447, and V-475 in support of the FAA's VOR Minimum Operation Network (MON) Program.
Amendment and Removal of VOR Federal Airways in the Eastern United States
This action amends 4 VHF Omnidirectional Range (VOR) Federal Airways, (V-7, V-9, V-106, and V-214); and removes 5 VOR Federal Airways, (V-58, V-130, V-149, V-445, V-451) in support of the FAA's VOR Minimum Operation Network (MON) project.
Amendment and Revocation of Air Traffic Service (ATS) Routes; Eastern United States
This action amends four jet routes and removes eight jet routes in the eastern United States. This action is associated with the Northeast Corridor Atlantic Coast Route Project and supports the VHF Omnidirectional Range (VOR) Minimum Operational Network (MON) to improve the efficiency of the National Airspace System (NAS) and reduce dependency on ground-based navigational systems.
Amendment of United States Area Navigation (RNAV) Route T-232; Fairbanks, AK
This action corrects a final rule published by the FAA in the Federal Register on August 29, 2022, that amends United States Area Navigation (RNAV) route T-232 in the vicinity of Fairbanks, AK, in support of a large and comprehensive T-route modernization project for the state of Alaska. The final rule identified the IMARE, AK, route point as a waypoint (WP), in error. This action makes an editorial correction to the references of the IMARE, AK, WP to change it to be reflected as a Fix and match the FAA's aeronautical database information.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is superseding Airworthiness Directive (AD) 2020-22- 03, which applied to all Airbus SAS Model A330-200, -200 Freighter, and -300 series airplanes. AD 2020-22-03 required revising the existing airplane flight manual (AFM) to incorporate procedures to be applied if an engine bleed over-temperature occurs when the associated engine bleed valve is jammed open, and provided for the optional embodiment of updated flight warning computer (FWC) software, which terminated the AFM revision. This AD was prompted by the development of new maintenance actions and software related to over-temperature failure conditions. This AD continues to require the actions specified in AD 2020-22-03, requires accomplishing the new maintenance tasks and corrective actions, and mandates embodiment of the updated FWC software for certain airplanes, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also prohibits the installation of affected FWC software. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A318, A319, A320, and A321 series airplanes. This AD was prompted by unclear and incomplete placard instructions for the doghouse door lock. This AD requires installing improved handling instruction placards on affected doghouses and re-identifying the doghouses, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also prohibits the installation of affected doghouses under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
Noise Compatibility Program for Laredo International Airport, Webb County, Texas
The Federal Aviation Administration (FAA) announces its determination that the noise exposure map submitted by Laredo International Airport is in compliance with applicable statutory and regulatory requirements.
Pipeline Safety: Information Collection Activities
In compliance with the Paperwork Reduction Act of 1995, this notice announces that the information collection requests abstracted below are being forwarded to the Office of Management and Budget (OMB) for review and comment. A Federal Register notice with a 60-day comment period soliciting comments on the information collections was published on June 16, 2022.
Fees for the Unified Carrier Registration Plan and Agreement
The Federal Motor Carrier Safety Administration is correcting a final rule that published September 1, 2022, in the Federal Register. The document amended the regulations for the annual registration fees States collect from motor carriers, motor private carriers of property, brokers, freight forwarders, and leasing companies for the Unified Carrier Registration (UCR) Plan and Agreement for the 2023 registration year and subsequent registration years.
Noise Exposure Map Notice: San Diego County Regional Airport Authority for San Diego International Airport
The Federal Aviation Administration (FAA) announces its determination that the noise exposure maps submitted by the San Diego County Regional Airport Authority for San Diego International Airport complies with applicable statutory and regulatory requirements, refer to the supplementary information for details. Further, in conjunction with the noise exposure maps, FAA is reviewing the proposed noise compatibility program for the San Diego International Airport, which the FAA will approve or disapprove on or before February 28, 2023. This notice also announces the availability of this noise compatibility program for public review and comment.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is superseding Airworthiness Directive (AD) 2015-12- 03, which applied to certain The Boeing Company Model 777-200, -200LR, -300, and -300ER series airplanes. AD 2015-12-03 required repetitive freeplay inspections and lubrication of the right and left elevators, rudder, and rudder tab, and related investigative and corrective actions if necessary. This AD was prompted by engineering testing which revealed that the force being applied to the elevator to detect excessive freeplay was insufficient. This AD continues to require certain actions in AD 2015-12-03 for certain airplanes, and requires revising the existing maintenance or inspection program, as applicable, for certain other airplanes, to incorporate a revised or new elevator freeplay maintenance procedure, as applicable. This AD also adds airplanes to the applicability. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Helicopters Deutschland GmbH (AHD) (Type Certificates Previously Held by Messerschmitt-Bolkow-Blohm [MBB], and Eurocopter Deutschland GmbH [ECD]) Helicopters
The FAA proposes to supersede airworthiness directive (AD) 77- 04-06, which applies to Messerschmitt-Bolkow-Blohm (MBB) (now Airbus Helicopters Deutschland GmbH (AHD)) Model BO-105A and BO-105 C helicopters; AD 2002-13-06, which applies to certain Eurocopter Deutschland GmbH (ECD) (now Airbus Helicopters Deutschland GmbH (AHD)) Model BO-105A, BO-105C, BO-105 C-2, BO-105 CB-2, BO-105 CB-4, BO-105 CS-2, BO-105 CBS-2, BO-105S, and BO-105LS A-1 helicopters; AD 2016-25- 14, which applies to certain Airbus Helicopters Deutschland GmbH (AHD) Model BO-105LS A-3 helicopters; and AD 2021-10-14, which applies to certain Airbus Helicopters Deutschland GmbH (AHD) Model BO-105A, BO- 105C, BO-105S, and BO-105LS A-3 helicopters. AD 77-04-06 requires reducing the life limit on certain main rotor gearbox (MGB) supports. AD 2002-13-06 requires determining the calendar age, number of flights, and flight hours time-in-service (TIS) on certain tension-torsion (TT) straps; revising the Airworthiness Limitations Schedule (ALS) of the existing maintenance manual; removing and replacing each TT strap that has exceeded its life limit, or if the TT strap's total hours TIS or number of flights and age are not known; and modifying certain parts. AD 2016-25-14 requires establishing a life limit for certain TT straps and removing certain parts that have exceeded the new life limit. AD 2021-10-14 requires replacement of certain TT straps with serviceable parts, and implementation of a new storage life limit for certain TT straps. Since the FAA issued those ADs, new and more restrictive airworthiness limitations have been issued. This proposed AD would require incorporating into existing maintenance records requirements (airworthiness limitations) as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). This proposed AD would also prohibit the installation of certain part-numbered TT straps. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; General Electric Company Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) GEnx-1B model turbofan engines. This AD was prompted by several reports of fuel leaks caused by high cycle fatigue (HCF) cracks found at the braze joints on fuel manifolds, and the subsequent manufacturer redesign of the high-pressure turbine (HPT) fuel hose variable stator vane (VSV) manifold, VSV fuel hose manifold, low-pressure turbine (LPT) fuel hose variable bleed valve (VBV) manifold, and VBV fuel hose manifold. This AD requires removal and replacement of the fuel hydraulic lines. The FAA is issuing this AD to address the unsafe condition on these products.
Privacy Act of 1974; Department of Transportation, Federal Aviation Administration, DOT/FAA 811, FAA Health Information Records
In accordance with the Privacy Act of 1974, the Department of Transportation (DOT) proposes to rename, update, and reissue an existing system of records notice currently titled DOT Federal Aviation Administration (FAA) system of records DOT/FAA 811, ``Employee Health Record System.'' This system of records notice (hereafter referred to as ``Notice'') previously covered FAA employees only. FAA employee occupational health care records and Health Awareness Program records are currently covered under the Office of Personnel Management (OPM)/ Government (GOVT)10 Employee Medical File System Records SORN (80 FR 74815November 30, 2015). The updated Notice covers the FAA's collection, use, and maintenance of non-occupational health records on federal employees, as well as FAA contractors and members of the public, such as students, interns and training and research participants, who receive emergency medical services at either the Civil Aerospace Medical Institute (CAMI) Occupational Health Clinic located at the Mike Monroney Aeronautical Center (MMAC) in Oklahoma City, OK, or the FAA Headquarters (HQ) Health Unit located in the HQ building in Washington, DC. Additionally, it covers FAA's collection of participation status (i.e., eligible, ineligible) on members of the public who engage in research and training programs at the agency. Any medical records collected in the course of these research or training programs is outside the scope of this Notice. The data collected in the system is a combination of health information and Personally Identifiable Information (PII) which is used to provide proper medical care and case management.
Maserati North America, Inc., Grant of Petition for Decision of Inconsequential Noncompliance
Maserati North America, Inc., (MNA), has determined that certain model year (MY) 2014-2021 Maserati Ghibli, Quattroporte, and Levante motor vehicles do not fully comply with Federal Motor Vehicle Safety Standard (FMVSS) No. 208, Occupant Crash Protection. MNA filed a noncompliance report dated August 5, 2021. MNA subsequently petitioned NHTSA on August 30, 2021, and amended its petition on January 13, 2022, for a decision that the subject noncompliance is inconsequential as it relates to motor vehicle safety. This document announces the grant of MNA's petition.
Assessment of the Continued Need for COVID-19 Emergency Declaration, Regulatory Relief for Commercial Motor Vehicle Operations
On August 31, 2022, FMCSA announced the extension of its coronavirus disease 2019 (COVID-19) Emergency Declaration which provides regulatory relief for motor carriers and drivers engaged in providing direct assistance in continued support of the Nation's COVID- 19 national emergency. The extension of the emergency declaration expires on October 15, 2022. FMCSA (the ``Agency'') seeks public comment concerning the extent to which motor carriers currently rely on the emergency declaration to deliver certain commodities and whether there has been any impact on safety.
Railroad Revenue Adequacy-2021 Determination
On September 6, 2022, the Board served a decision announcing the 2021 revenue adequacy determinations for the nation's Class I railroads. Five Class I railroads (BNSF Railroad Company, CSX Transportation, Inc., Norfolk Southern Combined Railroad Subsidiaries, Soo Line Corporation, and Union Pacific Railroad Company) were found to be revenue adequate.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Advisory Circular: Reporting of Laser Illumination of Aircraft
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval renew information collection. Advisory Circular 70-2A provides guidance to civilian air crews on the reporting of laser illumination incidents and recommended mitigation actions to be taken in order to ensure continued safe and orderly flight operations.
Airworthiness Directives; Piaggio Aero Industries S.p.A Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Piaggio Aero Industries S.p.A. (Piaggio) Model P-180 airplanes. This AD is prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI identifies the unsafe condition as altimetry system errors in the air data computers (ADCs) and stand-by instrument systems. This AD requires amending the existing airplane flight manual (AFM), installing improved ADCs and a detachable configuration module (DCM), and revising the existing instructions for continued airworthiness. The FAA is issuing this AD to address the unsafe condition on these products.
Privacy Act of 1974; Systems of Records
In accordance with the Privacy Act of 1974, the Department of Transportation (DOT) intends to modify and re-issue a DOT Federal Aviation Administration (FAA) system of records notice titled, ``DOT/ FAA 830Representatives of the Administrator.'' This system of records notice (hereafter referred to as ``Notice'') covers FAA records collected and maintained in support of FAA's management and oversight of individuals applying to become or are Representatives of the Administrator ``designees.'' Modification of DOT/FAA 830 is necessary due to changes and consolidation of the systems and processes used to manage designee programs.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
