Federal Aviation Administration 2008 – Federal Register Recent Federal Regulation Documents

The FAA is superseding an existing airworthiness directive (AD), which applies to all EMBRAER Model EMB-135BJ, -135ER, -135KE, - 135KL, -135LR, -145, -145ER, -145MR, -145LR, -145XR, -145MP, and -145EP airplanes. That AD currently requires reviewing the airplane maintenance records for recent reports of vibration from the tail section or rudder pedals. The existing AD also currently requires repetitively inspecting the skin, attachment fittings, and control rods of rudder II to detect cracking, loose parts, wear, or damage; and related investigative/corrective actions if necessary. This new AD requires the existing repetitive inspection to be done with new service information. This new AD also requires replacing the locking tab washers on the control rods of the rudder II and installing springs on the hinge assemblies of the rudder II, which would terminate the repetitive inspection requirements. This AD results from reports of rudder vibration due to wear. We are issuing this AD to prevent failure of multiple hinge fittings, which could result in severe vibration, and to prevent failure of the rudder control rods, which could result in jamming of the rudder II; and possible structural failure and reduced controllability of the airplane.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA is correcting a typographical error in an existing airworthiness directive (AD) that was published in the Federal Register on December 10, 2007 (72 FR 69593). The error resulted in a potential for confusion regarding the applicability of the AD. This AD applies to certain Airbus Model A318, A319, A320, and A321 series airplanes. This AD requires inspections of the landing gear (LG) selector valve 40GA and the LG door selector valve 41GA, to identify a possible hydraulic leak. The corrective action includes replacing the LG selector valve 40GA and/or the LG door selector valve 41GA if necessary.

This notice announces the bi-annual meeting of the Federal Aviation Administration (FAA) Aeronautical Charting Forum (ACF) to discuss informational content and design of aeronautical charts and related products, as well as instrument flight procedures development policy and design criteria.

This document makes a correction to a current notice of proposed rulemaking (NPRM), which was published in the Federal Register on February 20, 2008 (73 FR 9239), and applies to certain Taylorcraft Models A, B, and F series airplanes. The NPRM proposed to require inspection of the wing strut attach fittings for corrosion or cracks and would require repair or replacement if corrosion or cracks are found. The docket number was incorrectly referenced at ``FAA-2007- 0177'' instead of ``FAA-2008-0177.'' The NPRM is posted in the FAA- 2008-0177 docket section of the Federal Docket Management System (FDMS). This document corrects the docket number and should further reduce the confusion associated with the inadvertent error.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

This Notice sets forth the conditions under which a foreign air carrier may make an arrangement with a U.S. air carrier for a flight or series of flights, to be conducted with the foreign air carrier's aircraft and crew, for that U.S. certificated air carrier's- authorized services in foreign air transportation. This Notice also describes the regulatory steps involved for seeking Department approval for such an operation.

This action confirms the effective date of a direct final rule that establishes a Class E airspace area to support Area Navigation (RNAV) Global Positioning System (GPS) Special Instrument Approach Procedures (IAPs) that serve the Northwest Medical Center in Oil City, PA.

The FAA proposes to amend requirements concerning the registration of aircraft. This proposal is based on the need to increase and maintain the accuracy of aircraft registration information in the Civil Aviation Registry. The proposed procedures would ensure aircraft owners periodically provide information regarding changes in registration. These amendments would respond to the concerns of law enforcement and other government agencies and would provide more accurate, up-to-date aircraft registration information to all users of the Civil Aviation Registry database.

The FAA is adopting a new airworthiness directive (AD) for General Electric Company (GE) CF34-8C1/-8C5/-8C5B1/-8E5/-8E5A1, and CF34-10E series turbofan engines with certain part number (P/N) and serial number (SN) fuel metering units (FMU) installed. This AD requires a onetime test of the FMU for a miswired (reversed polarity) condition of the input wires to the overspeed solenoid. This AD results from the discovery of miswired FMU overspeed solenoids in the field. We are issuing this AD to prevent the engine from failing to shutdown during an overspeed which may lead to uncontained engine failure.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 767-200, -300, and -300F series airplanes. That AD currently requires reworking the surface of the ground stud bracket of the left and right transformer rectifier units (TRUs) and the airplane structure mounting surface, and measuring the resistance from the bracket to the structure and the ground lugs to the bracket using a bonding meter. This new AD revises the applicability of the existing AD to include additional airplanes and requires, among other actions, installation of a new ground stud bracket using faying surface bonding. This AD results from a report of loss of all direct current (DC) power generation during a flight, due to inadequate electrical ground path between the ground bracket of the TRUs/main battery charger (MBC) and the structure. We are issuing this AD to prevent depletion of the main battery while in flight, resulting from the loss of both TRUs and the MBC, and consequent loss of all DC power, which could impact the safe flight and landing of the airplane due to the loss of function or malfunction of essential/critical systems and displays in the cockpit.

Under the provisions of Title 49, U.S.C. Section 47153(c), notice is being given that the FAA is considering a request from the CartersvilleBartow County Airport Authority to waive the requirement that 1.095 acres in fee simple of federal property, located at the Cartersville Airport, be used for aeronautical purposes.

The FAA is issuing this notice to advise the public of a meeting of the Executive Committee of the Aviation Rulemaking Advisory Committee.

This action amends certain regulations governing U.S. registered aircraft operating beyond the territorial airspace of the United States. This action is necessary to correct an error in the recodification of the regulations concerning general operating and flight rules. The intended effect of this action is to correct an inadvertent error in the regulations.

The FAA is superseding an existing airworthiness directive (AD), which applies to all Dassault Model Falcon 2000, Mystere-Falcon 900, Falcon 900EX, Fan Jet Falcon, Mystere-Falcon 50, Mystere-Falcon 20, Mystere-Falcon 200, and Falcon 10 series airplanes. That AD currently requires repetitive tests and inspections to detect discrepancies of the overwing emergency exit, and corrective action if necessary. This new AD expands the applicability of the existing AD and extends the repetitive test and inspection intervals for all airplanes. This AD results from reports of incorrect operation of the overwing emergency exit due to interference between the emergency exit and the interior accommodation. We are issuing this AD to prevent failure of the overwing emergency exits to open, and consequent injury to passengers or crewmembers during an emergency evacuation.

The FAA invites public comments about or intention to request the Office of Management and Budget's (OMB) revision of a current information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on December 6, 2007, vol. 72, no. 234, page 68948. This project involves collecting data from recently certified ASEL pilots on the quality of their flight training and practical test experiences.

The FAA proposes to adopt a new airworthiness directive (AD) for General Electric Company (GE) CF6-80C2 and CF6-80E1 series turbofan engines. This proposed AD would require replacement of all clevis pins installed on the thrust reverser central drive units and upper and lower actuators, or replacement of pins that fail an on-wing rebound hardness test. This proposed AD results from failure of a thrust reverser during landing due to unapproved clevis pins being installed. The failure was due to lack of clevis pin hardness. We are proposing this AD to prevent thrust reverser failure, which could lead to damage to the thrust reverser and airplane.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

This Rule establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 707 airplanes, and Model 720 and 720B series airplanes. This AD requires revising the FAA-approved maintenance program by incorporating new airworthiness limitations (AWLs) for fuel tank systems to satisfy Special Federal Aviation Regulation No. 88 requirements. This AD also requires the initial performance of certain repetitive AWL inspections to phase in those inspections, and repair if necessary. This AD results from a design review of the fuel tank systems. We are issuing this AD to prevent the potential for ignition sources inside fuel tanks caused by latent failures, alterations, repairs, or maintenance actions, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.

We are adopting a new airworthiness directive (AD) to supersede AD 2007-16-14, which applies to all Taylorcraft (Taylorcraft) A, B, and F series airplanes. AD 2007-16-14 currently requires you to do an initial visual inspection of the left and right wing front and aft lift struts for cracks and corrosion and replace any cracked strut or strut with corrosion that exceeds certain limits. If the strut is replaced with an original design vented strut, AD 2007-16-14 requires you to repetitively inspect those struts thereafter. Since we issued AD 2007-16-14, we determined that the eddy current inspection method does not address the unsafe condition for the long term. We also determined that Models FA-III and TG-6 airplanes are not equipped with the affected struts. Consequently, this AD retains the actions required in AD 2007-16-14, except it removes the eddy current inspection method (provides 24-month credit if already done using this method), adds the radiograph method as an inspection method, changes the Applicability section, and changes the compliance time between the repetitive inspections. We are issuing this AD to detect and correct cracks and corrosion in the left and right wing front and aft lift struts. This condition, if not corrected, could result in failure of the lift strut and lead to in-flight separation of the wing.