Federal Aviation Administration August 5, 2009 – Federal Register Recent Federal Regulation Documents

This action proposes to modify Class E airspace at Pueblo Memorial Airport, CO. Additional controlled airspace is necessary to facilitate vectoring of Instrument Flight Rules (IFR) traffic from en route airspace to Pueblo Memorial Airport, CO. The FAA is proposing this action to enhance the safety and management of aircraft operations at Pueblo Memorial Airport, CO.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

This notice announces the FAA's schedule for transitioning to full electronic distribution of airworthiness directives (ADs). This transition will provide a timelier and more cost effective method for the FAA to provide safety information.

The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Boeing Model 747 airplanes. The existing AD currently requires repetitive inspections for cracking, and repair as necessary, of lower lobe body frames (sections 42 and 46) of the fuselage. The existing AD also provides for optional modification of the frames, which terminates the repetitive inspections. This proposed AD would require additional repetitive inspections for cracking of certain fuselage frames, and corrective actions if necessary. This proposed AD would also revise the AD applicability. This proposed AD results from a new report of a crack found in a body frame with a tapered side guide bracket at fuselage station 1800, located on the left side between stringers 39 and 40; the frame was severed. We are proposing this AD to detect and correct the loss of structural integrity of the fuselage, which could result in rapid depressurization of the airplane.

We are adopting a new airworthiness directive (AD) for the specified Agusta S.p.A. (Agusta) Model AB139 and AW139 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The aviation authority of Italy, with which we have a bilateral agreement, states in the MCAI that during the installation of a fire extinguisher bottle on a new helicopter, it was found that the electrical receptacle/connectors on the bottle which commands the firing of the extinguishing agent were swapped between engines No. 1 and No. 2. This condition could affect helicopters already in service and fire extinguisher bottles of the same part number in stock as spare parts. If not corrected, an improperly wired fire extinguishing bottle might cause the extinguishing agent to be discharged toward the unselected engine when the system is activated, rather than toward the engine with the fire. This AD requires determining if each engine has the proper outlet end on the electrical receptacle/connector that attaches the firing cartridge to the fire extinguisher bottle, and if not, replacing the fire extinguisher bottle. This AD is intended to prevent the fire extinguishing agent from not discharging toward the engine with the fire, which could result in loss of the helicopter due to an engine fire.

The FAA is superseding an existing airworthiness directive (AD) that applies to certain Boeing Model 737-100, -200, -200C, -300, - 400, and -500 series airplanes. That AD currently requires repetitive inspections of the intercostal webs, attachment clips, and stringer splice channels for cracks; and corrective action if necessary. This new AD reduces the repetitive inspection intervals from 25,000 flight cycles to 6,000 flight cycles, and expands the inspection area for Model 737-200C series airplanes to include the area aft of the forward entry door. This AD results from additional reports of fatigue cracks. We are issuing this AD to detect and correct fatigue cracking of the intercostals on the forward and aft sides of the forward entry door, which could result in loss of the forward entry door and rapid decompression of the airplane.

The FAA is adopting a new airworthiness directive (AD) for certain TCM IO-520, TSIO-520, and IO-550 series reciprocating engines, with certain SAP investment cast cylinder assemblies installed. This AD requires initial and repetitive inspections and compression tests to detect cracks in those cylinders with more than 750 flight hours (FH) time-in-service (TIS). This AD results from reports of cracks in the area of the exhaust valve and separation of cylinder heads from the barrels of SAP cylinder assemblies with certain part numbers. We are issuing this AD to prevent the separation of the cylinder head, which could result in immediate loss of engine power, possible structural damage to the engine, and possible fire in the engine compartment.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: