Airworthiness Directives; Agusta S.p.A. Model AB139 and AW139 Helicopters, 38899-38901 [E9-18430]
Download as PDF
Federal Register / Vol. 74, No. 149 / Wednesday, August 5, 2009 / Rules and Regulations
(i) If the cylinder pressure gauge reads
below 60 pounds per-square inch, determine
if the unacceptable pressure is due to a
cracked cylinder.
(ii) To check the cylinder, apply a 2
percent soapy water solution to the side of
the leaking cylinder.
(iii) If you see air bubbles, indicating air
leakage, on the side of the cylinder head, or
near the head-to-cylinder interface, replace
the cylinder assembly before further flight.
(h) Thereafter, repeat the cylinder visual
inspections and compression tests within 50
FH time-since-last inspection (TSLI) until the
cylinders reach their time-between-overhaul
(TBO) limits specified in Teledyne
Continental Aircraft Engine Service
Information Letter SIL98–9A, Revision A,
dated March 28, 2003.
Replacing SAP Cylinder Assemblies
(i) For TCM IO–520, TSIO–520, and IO–
550 series reciprocating engines with SAP
investment cast cylinder assemblies, P/Ns
SA52000–A1, SA52000–A20P, SA52000–
A21P, SA52000–A22P, SA52000–A23P,
SA55000–A1, or SA55000–A20P, replace the
SAP cylinder head assembly at the first TBO
after the effective date of this AD. Engines
that were already overhauled may continue
in service until the first TBO after the
effective date of this AD.
Prohibition Against Installing Certain P/N
SAP Cylinder Assemblies
(j) After the effective date of this AD, do
not install any SAP investment cast cylinder
assembly, P/Ns SA52000–A1, SA52000–
A20P, SA52000–A21P, SA52000–A22P,
SA52000–A23P, SA55000–A1, or SA55000–
A20P, in any engine.
Alternative Methods of Compliance
(k) The Manager, Special Certification
Office, has the authority to approve
alternative methods of compliance for this
AD if requested using the procedures found
in 14 CFR 39.19.
Special Flight Permits
(l) Under 14 CFR part 39.23, we will not
approve special flight permits for this AD for
engines that have failed the visual inspection
or the 50 hour periodic cylinder assembly
compression test required by this AD.
srobinson on DSKHWCL6B1PROD with RULES
Related Information
(m) Teledyne Continental Service Bulletin
No. SB03–3 ‘‘Differential Pressure Test and
Borescope Inspection Procedures for
Cylinders’’, dated March 28, 2003.
(n) Contact Peter W. Hakala, Aerospace
Engineer, Special Certification Office, FAA,
Rotorcraft Directorate, 2601 Meacham Blvd.,
Fort Worth, TX 76137; e-mail:
peter.w.hakala@faa.gov; telephone (817)
222–5145; fax (817) 222–5785, for more
information about this AD.
Material Incorporated by Reference
(o) You must use Teledyne Continental
Aircraft Engine Service Information Letter
SIL98–9A, Revision A, dated March 28, 2003
to determine the times-between-overhaul
required by this AD. The Director of the
Federal Register approved the incorporation
by reference of this service information in
VerDate Nov<24>2008
16:20 Aug 04, 2009
Jkt 217001
accordance with 5 U.S.C. 552(a) and 1 CFR
part 51. Contact Teledyne Continental
Motors, Inc., P.O. Box 90, Mobile, Alabama;
telephone (251) 438–3411, or go to: https://
www.genuinecontinental.aero, for a copy of
this service information. You may review
copies at the FAA, New England Region, 12
New England Executive Park, Burlington,
MA; or at the National Archives and Records
Administration (NARA). For information on
the availability of this material at NARA, call
202–741–6030, or go to: https://
www.archives.gov/federal-register/cfr/ibrlocations.html.
Issued in Burlington, Massachusetts, on
July 23, 2009.
Peter A. White,
Assistant Manager, Engine and Propeller
Directorate, Aircraft Certification Service.
[FR Doc. E9–18220 Filed 8–4–09; 8:45 am]
BILLING CODE 4910–13–P
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA–2009–0168; Directorate
Identifier 2007–SW–33–AD; Amendment 39–
15977; AD 2009–15–14]
RIN 2120–AA64
Airworthiness Directives; Agusta
S.p.A. Model AB139 and AW139
Helicopters
AGENCY: Federal Aviation
Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
SUMMARY: We are adopting a new
airworthiness directive (AD) for the
specified Agusta S.p.A. (Agusta) Model
AB139 and AW139 helicopters. This AD
results from mandatory continuing
airworthiness information (MCAI)
originated by an aviation authority of
another country to identify and correct
an unsafe condition on an aviation
product. The aviation authority of Italy,
with which we have a bilateral
agreement, states in the MCAI that
during the installation of a fire
extinguisher bottle on a new helicopter,
it was found that the electrical
receptacle/connectors on the bottle
which commands the firing of the
extinguishing agent were swapped
between engines No. 1 and No. 2. This
condition could affect helicopters
already in service and fire extinguisher
bottles of the same part number in stock
as spare parts. If not corrected, an
improperly wired fire extinguishing
bottle might cause the extinguishing
agent to be discharged toward the
unselected engine when the system is
activated, rather than toward the engine
PO 00000
Frm 00013
Fmt 4700
Sfmt 4700
38899
with the fire. This AD requires
determining if each engine has the
proper outlet end on the electrical
receptacle/connector that attaches the
firing cartridge to the fire extinguisher
bottle, and if not, replacing the fire
extinguisher bottle. This AD is intended
to prevent the fire extinguishing agent
from not discharging toward the engine
with the fire, which could result in loss
of the helicopter due to an engine fire.
DATES: This AD becomes effective on
September 9, 2009.
The incorporation by reference of
certain publications is approved by the
Director of the Federal Register as of
September 9, 2009.
ADDRESSES: You may examine the AD
docket on the Internet at https://
regulations.gov or in person at the
Docket Operations office, U.S.
Department of Transportation, M–30,
West Building Ground Floor, Room
W12–140, 1200 New Jersey Avenue, SE.,
Washington, DC between 9 a.m. and 5
p.m. Monday through Friday, except
Federal holidays.
You may get the service information
identified in this AD from Agusta, Via
Giovanni Agusta, 520 21017 Cascina
Costa di Samarate (VA), Italy, telephone
39 0331–229111, fax 39 0331–229605/
222595, or at https://
customersupport.agusta.com/
technical_advice.php.
Examining The AD Docket: The AD
docket contains the Notice of proposed
rulemaking (NPRM), the economic
evaluation, any comments received, and
other information. The street address
and operating hours for the Docket
Operations office (telephone (800) 647–
5527) are in the ADDRESSES section of
this AD. Comments will be available in
the AD docket shortly after they are
received.
FOR FURTHER INFORMATION CONTACT: John
Strasburger, Aviation Safety Engineer
FAA, Rotorcraft Directorate, Regulations
and Policy Group, 2601 Meacham Blvd.,
Fort Worth, Texas 76137; telephone
(817) 222–5167; fax (817) 222–5961.
SUPPLEMENTARY INFORMATION:
Discussion
We issued an NPRM to amend 14 CFR
part 39 to include an AD that would
apply to Agusta Model AB139 and
AW139 helicopters on February 19,
2009. That NPRM was published in the
Federal Register on March 9, 2009 (74
FR 9971). That NPRM proposed to
require determining if each engine has
the proper outlet end on the electrical
receptacle/connector that attaches the
firing cartridge to the fire extinguisher
bottle, and if not, replacing the fire
extinguisher bottle. The proposed AD
E:\FR\FM\05AUR1.SGM
05AUR1
38900
Federal Register / Vol. 74, No. 149 / Wednesday, August 5, 2009 / Rules and Regulations
actions are intended to prevent the fire
extinguishing agent from not
discharging toward the engine with the
fire, which could result in loss of the
helicopter due to an engine fire. You
may obtain further information by
examining the MCAI and any related
service information in the AD docket.
Comments
By publishing the NPRM, we gave the
public an opportunity to participate in
developing this AD. However, we
received no comment on the NPRM or
on our determination of the cost to the
public. Therefore, based on our review
and evaluation of the available data, we
have determined that air safety and the
public interest require adopting the AD
as proposed.
Relevant Service Information
Agusta has issued Bollettino Tecnico
No. 139–085, dated May 18, 2007. The
actions described in the MCAI are
intended to correct the same unsafe
condition as that identified in the
service information.
srobinson on DSKHWCL6B1PROD with RULES
Differences Between This AD and the
MCAI AD
We have reviewed the MCAI AD and
related service information and, in
general, agree with their substance.
However, our AD differs from the MCAI
AD to clarify the unsafe condition and
compliance instructions. In making
these changes, we do not intend to differ
substantively from the information
provided in the MCAI and related
service information. These differences
are highlighted in the ‘‘Differences
Between the FAA AD and the MCAI
AD’’ section in the AD.
Costs of Compliance
We estimate that this AD will affect
about 20 helicopters of U.S. registry and
that it will take about 1 work-hour per
helicopter to verify the correct
installation of electrical receptacles/
connectors on the two fire extinguisher
bottles. We also estimate that it will take
about 3 work-hours per helicopter to
replace a fire extinguisher bottle with
the inverted electrical receptacles/
connectors and that about 5% (2 bottles)
of the fire extinguisher bottles in the
fleet will have to be replaced. The
average labor rate is $80 per work hour.
The cost of a replacement fire
extinguisher bottle is $10,300. Based on
these figures, we estimate the cost of
this AD on U.S. operators to be $22,680.
Authority for This Rulemaking
Title 49 of the United States Code
specifies the FAA’s authority to issue
rules on aviation safety. Subtitle I,
VerDate Nov<24>2008
16:20 Aug 04, 2009
Jkt 217001
section 106, describes the authority of
the FAA Administrator. ‘‘Subtitle VII:
Aviation Programs,’’ describes in more
detail the scope of the Agency’s
authority.
We are issuing this rulemaking under
the authority described in ‘‘Subtitle VII,
Part A, Subpart III, Section 44701:
General requirements.’’ Under that
section, Congress charges the FAA with
promoting safe flight of civil aircraft in
air commerce by prescribing regulations
for practices, methods, and procedures
the Administrator finds necessary for
safety in air commerce. This regulation
is within the scope of that authority
because it addresses an unsafe condition
that is likely to exist or develop on
product(s) identified in this rulemaking
action.
Regulatory Findings
We determined that this AD will not
have federalism implications under
Executive Order 13132. This AD will
not have a substantial direct effect on
the States, on the relationship between
the national government and the States,
or on the distribution of power and
responsibilities among the various
levels of government.
Therefore, I certify this AD:
1. Is not a ‘‘significant regulatory
action’’ under Executive Order 12866;
2. Is not a ‘‘significant rule’’ under the
DOT Regulatory Policies and Procedures
(44 FR 11034, February 26, 1979); and
3. Will not have a significant
economic impact, positive or negative,
on a substantial number of small entities
under the criteria of the Regulatory
Flexibility Act.
We prepared an economic evaluation
of the estimated costs to comply with
this AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation
safety, Incorporation by reference,
Safety.
Adoption of the Amendment
Accordingly, under the authority
delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as
follows:
■
PART 39—AIRWORTHINESS
DIRECTIVES
1. The authority citation for part 39
continues to read as follows:
■
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13
[Amended]
2. The FAA amends § 39.13 by adding
the following new AD:
■
PO 00000
Frm 00014
Fmt 4700
Sfmt 4700
Effective Date
2009–15–14 Agusta S.p.A.: Amendment 39–
15977; Docket No. FAA–2009–0168;
Directorate Identifier 2007–SW–33–AD.
(a) This airworthiness directive (AD)
becomes effective on September 9, 2009.
Other Affected ADs
(b) None.
Applicability
(c) This AD applies to Model AB139
helicopters, serial number (S/N) 31005
through 31054, except S/N 31007, and
AW139 helicopters, S/N 31055 through
31067, S/N 31070, and S/N 31071,
certificated in any category.
Reason
(d) The mandatory continuing
airworthiness information (MCAI) states that
during the installation of a fire extinguisher
bottle, part number 3G2620V00131, on a
helicopter during manufacture, it was found
that the electrical receptacle/connectors on
the bottle which commands the firing of the
extinguishing agent were swapped between
engines No. 1 and No. 2. This condition
could affect helicopters already in service
and fire extinguisher bottles of the same part
number in stock as spare parts. If not
corrected, an improperly wired fire
extinguishing bottle might cause the
extinguishing agent to be discharged toward
the unselected engine when the system is
activated, rather than toward the engine with
the fire. This AD requires determining if each
engine has the proper outlet end on the
electrical receptacle/connector that attaches
the firing cartridge to the fire extinguisher
bottle, and if not, replacing the fire
extinguisher bottle. This AD is intended to
prevent the fire extinguishing agent from not
discharging toward the engine with the fire,
which could result in loss of the helicopter
due to an engine fire.
Actions and Compliance
(e) Within 100 hours time-in-service (TIS)
or 3 months, whichever occurs first, unless
already done, do the following actions.
(1) Determine whether the fire
extinguishing bottle (bottle) for engines No.
1 and No. 2 have the proper outlet end on
the electrical receptacle/connector, which
attaches the firing cartridge to the bottle, by
following steps 4. and 5. of the Compliance
Instructions in Agusta Bollettino Tecnico No.
139–085, dated May 18, 2007 (BT).
(2) If a bottle has an electrical receptacle/
connector for the firing cartridge with an
improper outlet end, before further flight,
replace the bottle with a bottle that has an
electrical receptacle/connector with a proper
outlet end in accordance with step 6. of the
Compliance Instructions in the BT.
Differences Between This AD and the MCAI
AD
(f) This AD uses the term ‘‘hours time-inservice’’ rather than ‘‘flight hours.’’
Other Information
(g) Alternative Methods of Compliance
(AMOCs): The Manager, Safety Management
Group, Rotorcraft Directorate, FAA, ATTN:
John Strasburger, Aviation Safety Engineer,
E:\FR\FM\05AUR1.SGM
05AUR1
Federal Register / Vol. 74, No. 149 / Wednesday, August 5, 2009 / Rules and Regulations
FAA, Rotorcraft Directorate, Regulations and
Policy Group, 2601 Meacham Blvd., Fort
Worth, Texas 76137; telephone (817) 222–
5167; fax (817) 222–5961, has the authority
to approve AMOCs for this AD, if requested
using the procedures found in 14 CFR 39.19.
Related Information
(h) MCAI Ente Nazionale Per L’Aviazione
Civile Airworthiness Directive No. 2007–227,
dated June 18, 2007, contains related
information.
Joint Aircraft System/Component (JASC)
Code
(i) JASC Code 2621: Fire Bottle, Fixed.
Material Incorporated by Reference
(j) You must use the specified portions of
Agusta Bollettino Tecnico No. 139–085,
dated May 18, 2007 to do the actions
required.
(1) The Director of the Federal Register
approved the incorporation by reference of
this service information under 5 U.S.C.
552(a) and 1 CFR part 51.
(2) For service information identified in
this AD, contact Agusta, Via Giovanni
Agusta, 520 21017 Cascina Costa di Samarate
(VA), Italy, telephone 39 0331–229111, fax 39
0331–229605/222595, or at https://
customersupport.agusta.com/
technical_advice.php.
(3) You may review copies at the FAA,
Office of the Regional Counsel, Southwest
Region, 2601 Meacham Blvd., Room 663, Fort
Worth, Texas; or at the National Archives
and Records Administration (NARA). For
information on the availability of this
material at NARA, call (202) 741–6030, or go
to: https://www.archives.gov/federal-register/
cfr/ibr-locations.html.
Issued in Fort Worth, Texas, on July 10,
2009.
Larry M. Kelly,
Acting Manager, Rotorcraft Directorate,
Aircraft Certification Service.
[FR Doc. E9–18430 Filed 8–4–09; 8:45 am]
BILLING CODE 4910–13–P
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA–2008–1213; Directorate
Identifier 2007–NM–092–AD; Amendment
39–15987; AD 2009–16–14]
RIN 2120–AA64
srobinson on DSKHWCL6B1PROD with RULES
Airworthiness Directives; Boeing
Model 737–100, –200, –200C, –300,
–400, and –500 Series Airplanes
AGENCY: Federal Aviation
Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
SUMMARY: The FAA is superseding an
existing airworthiness directive (AD)
that applies to certain Boeing Model
VerDate Nov<24>2008
16:20 Aug 04, 2009
Jkt 217001
737–100, –200, –200C, –300, –400, and
–500 series airplanes. That AD currently
requires repetitive inspections of the
intercostal webs, attachment clips, and
stringer splice channels for cracks; and
corrective action if necessary. This new
AD reduces the repetitive inspection
intervals from 25,000 flight cycles to
6,000 flight cycles, and expands the
inspection area for Model 737–200C
series airplanes to include the area aft
of the forward entry door. This AD
results from additional reports of fatigue
cracks. We are issuing this AD to detect
and correct fatigue cracking of the
intercostals on the forward and aft sides
of the forward entry door, which could
result in loss of the forward entry door
and rapid decompression of the
airplane.
DATES: This AD becomes effective
September 9, 2009.
The Director of the Federal Register
approved the incorporation by reference
of a certain publication listed in the AD
as of September 9, 2009.
ADDRESSES: For service information
identified in this AD, contact Boeing
Commercial Airplanes, Attention: Data
& Services Management, P.O. Box 3707,
MC 2H–65, Seattle, Washington 98124–
2207; telephone 206–544–5000,
extension 1; fax 206–766–5680; e-mail
me.boecom@boeing.com; Internet
https://www.myboeingfleet.com.
Examining the AD Docket
You may examine the AD docket on
the Internet at https://
www.regulations.gov; or in person at the
Docket Management Facility between 9
a.m. and 5 p.m., Monday through
Friday, except Federal holidays. The AD
docket contains this AD, the regulatory
evaluation, any comments received, and
other information. The address for the
Docket Office (telephone 800–647–5527)
is the Document Management Facility,
U.S. Department of Transportation,
Docket Operations, M–30, West
Building Ground Floor, Room W12–140,
1200 New Jersey Avenue, SE.,
Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT:
Alan Pohl, Aerospace Engineer,
Airframe Branch, ANM–120S, FAA,
Seattle Aircraft Certification Office,
1601 Lind Avenue, SW., Renton,
Washington 98057–3356; telephone
(425) 917–6450; fax (425) 917–6590.
SUPPLEMENTARY INFORMATION:
Discussion
The FAA issued a notice of proposed
rulemaking (NPRM) to amend 14 CFR
part 39 to include an AD that
supersedes AD 2005–20–03, amendment
39–14296 (70 FR 56361, September 27,
PO 00000
Frm 00015
Fmt 4700
Sfmt 4700
38901
2005). The existing AD applies to
certain Boeing Model 737–100, –200,
–200C, –300, –400, and –500 series
airplanes. That NPRM was published in
the Federal Register on November 17,
2008 (73 FR 67815). That NPRM
proposed to continue to require
repetitive inspections of the intercostal
webs, attachment clips, and stringer
splice channels for cracks, at repetitive
inspection intervals reduced from
25,000 flight cycles to 6,000 flight
cycles; and corrective action if
necessary. That NPRM also proposed to
expand the inspection area for Model
737–200C series airplanes to include the
area aft of the forward entry door.
Comments
We provided the public the
opportunity to participate in the
development of this AD. We have
considered the comments that have
been received on the NPRM.
Request to Increase Grace Period
US Airways requests that we increase
the threshold grace period from 3,000
flight cycles after the effective date of
this AD to 4,500 flight cycles. US
Airways states that the new grace period
it requests would allow operators to
schedule more airplanes into
appropriate maintenance tasks. US
Airways explains that the inspection
would affect its operation by requiring
additional maintenance that is not
presently scheduled.
We do not agree with the commenter’s
request. In developing an appropriate
compliance time for this AD, we
considered not only the safety
implications, but the manufacturer’s
recommendations, and the practical
aspect of accomplishing the
modification within an interval of time
that corresponds to typical scheduled
maintenance for affected operators.
However, under the provisions of
paragraph (m) of this AD, we may
consider requests for adjustments to the
compliance time if data are submitted to
substantiate that such an adjustment
would provide an acceptable level of
safety. We have not changed this AD in
this regard.
Explanation of Additional Changes to
the AD
We have clarified paragraphs (h), (i),
and (l) of this AD to include the full
citation for the service information
referenced in those paragraphs. We
made this change to ensure that it is
clear which service information
operators must use for a specific action.
We have changed paragraph (j) of this
AD to remove the reference to ‘‘Part 4
of the Work Instructions of Boeing
E:\FR\FM\05AUR1.SGM
05AUR1
Agencies
[Federal Register Volume 74, Number 149 (Wednesday, August 5, 2009)]
[Rules and Regulations]
[Pages 38899-38901]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: E9-18430]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2009-0168; Directorate Identifier 2007-SW-33-AD;
Amendment 39-15977; AD 2009-15-14]
RIN 2120-AA64
Airworthiness Directives; Agusta S.p.A. Model AB139 and AW139
Helicopters
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for the
specified Agusta S.p.A. (Agusta) Model AB139 and AW139 helicopters.
This AD results from mandatory continuing airworthiness information
(MCAI) originated by an aviation authority of another country to
identify and correct an unsafe condition on an aviation product. The
aviation authority of Italy, with which we have a bilateral agreement,
states in the MCAI that during the installation of a fire extinguisher
bottle on a new helicopter, it was found that the electrical
receptacle/connectors on the bottle which commands the firing of the
extinguishing agent were swapped between engines No. 1 and No. 2. This
condition could affect helicopters already in service and fire
extinguisher bottles of the same part number in stock as spare parts.
If not corrected, an improperly wired fire extinguishing bottle might
cause the extinguishing agent to be discharged toward the unselected
engine when the system is activated, rather than toward the engine with
the fire. This AD requires determining if each engine has the proper
outlet end on the electrical receptacle/connector that attaches the
firing cartridge to the fire extinguisher bottle, and if not, replacing
the fire extinguisher bottle. This AD is intended to prevent the fire
extinguishing agent from not discharging toward the engine with the
fire, which could result in loss of the helicopter due to an engine
fire.
DATES: This AD becomes effective on September 9, 2009.
The incorporation by reference of certain publications is approved
by the Director of the Federal Register as of September 9, 2009.
ADDRESSES: You may examine the AD docket on the Internet at https://regulations.gov or in person at the Docket Operations office, U.S.
Department of Transportation, M-30, West Building Ground Floor, Room
W12-140, 1200 New Jersey Avenue, SE., Washington, DC between 9 a.m. and
5 p.m. Monday through Friday, except Federal holidays.
You may get the service information identified in this AD from
Agusta, Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA),
Italy, telephone 39 0331-229111, fax 39 0331-229605/222595, or at
https://customersupport.agusta.com/technical_advice.php.
Examining The AD Docket: The AD docket contains the Notice of
proposed rulemaking (NPRM), the economic evaluation, any comments
received, and other information. The street address and operating hours
for the Docket Operations office (telephone (800) 647-5527) are in the
ADDRESSES section of this AD. Comments will be available in the AD
docket shortly after they are received.
FOR FURTHER INFORMATION CONTACT: John Strasburger, Aviation Safety
Engineer FAA, Rotorcraft Directorate, Regulations and Policy Group,
2601 Meacham Blvd., Fort Worth, Texas 76137; telephone (817) 222-5167;
fax (817) 222-5961.
SUPPLEMENTARY INFORMATION:
Discussion
We issued an NPRM to amend 14 CFR part 39 to include an AD that
would apply to Agusta Model AB139 and AW139 helicopters on February 19,
2009. That NPRM was published in the Federal Register on March 9, 2009
(74 FR 9971). That NPRM proposed to require determining if each engine
has the proper outlet end on the electrical receptacle/connector that
attaches the firing cartridge to the fire extinguisher bottle, and if
not, replacing the fire extinguisher bottle. The proposed AD
[[Page 38900]]
actions are intended to prevent the fire extinguishing agent from not
discharging toward the engine with the fire, which could result in loss
of the helicopter due to an engine fire. You may obtain further
information by examining the MCAI and any related service information
in the AD docket.
Comments
By publishing the NPRM, we gave the public an opportunity to
participate in developing this AD. However, we received no comment on
the NPRM or on our determination of the cost to the public. Therefore,
based on our review and evaluation of the available data, we have
determined that air safety and the public interest require adopting the
AD as proposed.
Relevant Service Information
Agusta has issued Bollettino Tecnico No. 139-085, dated May 18,
2007. The actions described in the MCAI are intended to correct the
same unsafe condition as that identified in the service information.
Differences Between This AD and the MCAI AD
We have reviewed the MCAI AD and related service information and,
in general, agree with their substance. However, our AD differs from
the MCAI AD to clarify the unsafe condition and compliance
instructions. In making these changes, we do not intend to differ
substantively from the information provided in the MCAI and related
service information. These differences are highlighted in the
``Differences Between the FAA AD and the MCAI AD'' section in the AD.
Costs of Compliance
We estimate that this AD will affect about 20 helicopters of U.S.
registry and that it will take about 1 work-hour per helicopter to
verify the correct installation of electrical receptacles/connectors on
the two fire extinguisher bottles. We also estimate that it will take
about 3 work-hours per helicopter to replace a fire extinguisher bottle
with the inverted electrical receptacles/connectors and that about 5%
(2 bottles) of the fire extinguisher bottles in the fleet will have to
be replaced. The average labor rate is $80 per work hour. The cost of a
replacement fire extinguisher bottle is $10,300. Based on these
figures, we estimate the cost of this AD on U.S. operators to be
$22,680.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on product(s) identified in this
rulemaking action.
Regulatory Findings
We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
Therefore, I certify this AD:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared an economic evaluation of the estimated costs to comply
with this AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new AD:
Effective Date
2009-15-14 Agusta S.p.A.: Amendment 39-15977; Docket No. FAA-2009-
0168; Directorate Identifier 2007-SW-33-AD.
(a) This airworthiness directive (AD) becomes effective on
September 9, 2009.
Other Affected ADs
(b) None.
Applicability
(c) This AD applies to Model AB139 helicopters, serial number
(S/N) 31005 through 31054, except S/N 31007, and AW139 helicopters,
S/N 31055 through 31067, S/N 31070, and S/N 31071, certificated in
any category.
Reason
(d) The mandatory continuing airworthiness information (MCAI)
states that during the installation of a fire extinguisher bottle,
part number 3G2620V00131, on a helicopter during manufacture, it was
found that the electrical receptacle/connectors on the bottle which
commands the firing of the extinguishing agent were swapped between
engines No. 1 and No. 2. This condition could affect helicopters
already in service and fire extinguisher bottles of the same part
number in stock as spare parts. If not corrected, an improperly
wired fire extinguishing bottle might cause the extinguishing agent
to be discharged toward the unselected engine when the system is
activated, rather than toward the engine with the fire. This AD
requires determining if each engine has the proper outlet end on the
electrical receptacle/connector that attaches the firing cartridge
to the fire extinguisher bottle, and if not, replacing the fire
extinguisher bottle. This AD is intended to prevent the fire
extinguishing agent from not discharging toward the engine with the
fire, which could result in loss of the helicopter due to an engine
fire.
Actions and Compliance
(e) Within 100 hours time-in-service (TIS) or 3 months,
whichever occurs first, unless already done, do the following
actions.
(1) Determine whether the fire extinguishing bottle (bottle) for
engines No. 1 and No. 2 have the proper outlet end on the electrical
receptacle/connector, which attaches the firing cartridge to the
bottle, by following steps 4. and 5. of the Compliance Instructions
in Agusta Bollettino Tecnico No. 139-085, dated May 18, 2007 (BT).
(2) If a bottle has an electrical receptacle/connector for the
firing cartridge with an improper outlet end, before further flight,
replace the bottle with a bottle that has an electrical receptacle/
connector with a proper outlet end in accordance with step 6. of the
Compliance Instructions in the BT.
Differences Between This AD and the MCAI AD
(f) This AD uses the term ``hours time-in-service'' rather than
``flight hours.''
Other Information
(g) Alternative Methods of Compliance (AMOCs): The Manager,
Safety Management Group, Rotorcraft Directorate, FAA, ATTN: John
Strasburger, Aviation Safety Engineer,
[[Page 38901]]
FAA, Rotorcraft Directorate, Regulations and Policy Group, 2601
Meacham Blvd., Fort Worth, Texas 76137; telephone (817) 222-5167;
fax (817) 222-5961, has the authority to approve AMOCs for this AD,
if requested using the procedures found in 14 CFR 39.19.
Related Information
(h) MCAI Ente Nazionale Per L'Aviazione Civile Airworthiness
Directive No. 2007-227, dated June 18, 2007, contains related
information.
Joint Aircraft System/Component (JASC) Code
(i) JASC Code 2621: Fire Bottle, Fixed.
Material Incorporated by Reference
(j) You must use the specified portions of Agusta Bollettino
Tecnico No. 139-085, dated May 18, 2007 to do the actions required.
(1) The Director of the Federal Register approved the
incorporation by reference of this service information under 5
U.S.C. 552(a) and 1 CFR part 51.
(2) For service information identified in this AD, contact
Agusta, Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate
(VA), Italy, telephone 39 0331-229111, fax 39 0331-229605/222595, or
at https://customersupport.agusta.com/technical_advice.php.
(3) You may review copies at the FAA, Office of the Regional
Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth,
Texas; or at the National Archives and Records Administration
(NARA). For information on the availability of this material at
NARA, call (202) 741-6030, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.
Issued in Fort Worth, Texas, on July 10, 2009.
Larry M. Kelly,
Acting Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. E9-18430 Filed 8-4-09; 8:45 am]
BILLING CODE 4910-13-P