Department of Transportation 2016 – Federal Register Recent Federal Regulation Documents

This action modifies Class E airspace extending upward from 700 feet above the surface at Taos Regional Airport, Taos, NM. Decommissioning of non-directional radio beacon (NDB) and cancellation of the NDB approaches due to advances in Global Positioning System (GPS) capabilities have made this action necessary for the safety and management of Instrument Flight Rules (IFR) operations at Taos Regional Airport.

We propose to adopt a new airworthiness directive (AD) for RUAG Aerospace Services GmbH Models 228-100, 228-101, 228-200, 228-201, 228-202, and 228-212 airplanes that would supersede AD 2009-13-04. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as excessive wear on the guide pin of the power lever or condition lever which could cause functional loss of the flight idle stop. We are issuing this proposed AD to require actions to address the unsafe condition on these products.

We propose to adopt a new airworthiness directive (AD) for certain Fokker Services B.V. Model F.28 airplanes. This proposed AD prompted by reports indicating that the main landing gear (MLG) could not be extended and locked down during approach. This proposed AD would require a detailed inspection of the restrictor check valve filter screens to detect any degraded or failed filter screens, and installation of serviceable parts. We are proposing this AD to detect and correct any degraded or failed filter screens. This condition, if not corrected, could prevent MLG extension and lock-down and result in an emergency landing with consequent injury to occupants and damage to the airplane.

We are superseding Airworthiness Directive (AD) 2005-18-18 for certain The Boeing Company Model 757 airplanes. AD 2005-18-18 required inspections of certain wire bundles in the left and right engine-to- wing aft fairings for discrepancies; installation of back-to-back p- clamps between the wire and hydraulic supply tube at the aft end of the right-hand strut only; and associated re-routing of the wire bundles, if necessary. This new AD also requires an installation of spiral cable wrap on fuel shutoff valve (FSV) wires at the aft end of the strut, for both left and right engines, and related investigative and corrective actions. This AD was prompted by a determination that the service information referenced in AD 2005-18-18 did not adequately address FSV wires at the aft end of the struts. We are issuing this AD to prevent chafing between the wire bundle and the structure of the aft fairing, which could result in electrical arcing and subsequent ignition of flammable vapors and a possible uncontrollable fire.

This action would streamline and improve commercial space transportation regulations' general rulemaking and petition procedures by reflecting current practice; reorganizing the regulations for clarity and flow; and allowing petitioners to file their petitions to the FAA's Office of Commercial Space Transportation electronically. Further, it would expand the option to satisfy commercial space transportation requirements by demonstrating an equivalent level of safety. These changes are necessary to ensure the regulations are current, accurate, and are not unnecessarily burdensome. The intended effect of these changes is to improve the clarity of the regulations and reduce burden on the industry and on the FAA.

The FHWA is extending the period for submitting applications to the Notice of Funding Opportunity (NOFO) published March 29, 2016, for the advanced transportation and congestion management technologies deployment program. The original due date for applications was June 3, 2016. The extension is based on requests from potential eligible entities for additional time to prepare and submit applications.

This notice is to advise interested persons that on Tuesday, June 14, 2016, the Department of Transportation (DOT) and the Pipeline and Hazardous Materials Safety Administration (PHMSA) will conduct a public meeting in preparation for the 49th session of the United Nations Sub-Committee of Experts on the Transport of Dangerous Goods (UN SCOE TDG). The UN SCOE TDG meeting will be held July 27 to July 6, 2016, in Geneva, Switzerland. PHMSA is soliciting comments about potential new work items, which may be considered for inclusion in its international agenda and feedback on issues that PHMSA may put forward for consideration by the Sub-Committee. (See the SUPPLEMENTARY INFORMATION section below for a list of potential UN SCOE TDG meeting topics.) Also on Tuesday, June 14, 2016, the Occupational Safety and Health Administration (OSHA) will conduct a public meeting (Docket No. OSHA- 2016-0005) to discuss proposals in preparation for the 31st session of the United Nations Sub-Committee of Experts on the Globally Harmonized System of Classification and Labelling of Chemicals (UNSCEGHS), to be held July 5 to 8, 2016, in Geneva, Switzerland. Time and Location: Both the PHMSA and the OSHA public meetings will take place on Tuesday, June 14, 2016, at the DOT Headquarters, which is located at 1200 New Jersey Avenue SE, Washington, DC 20590-0001. PHMSA will host its public meeting between 9:00 am to 12:00 p.m. EST in Conference Room 4 in DOT Headquarters, West Building. Then, OSHA will host its public meeting between 1:00 p.m. to 4:00 p.m. EST in Conference Room 4 in DOT Headquarters, West Building. Advanced Meeting Registration: The DOT requests that attendees pre- register for these meetings by completing the form at https:// www.surveymonkey.com/r/Q3Z53PT. Attendees may use the same form to pre- register for both the PHMSA and the OSHA meetings. Failure to pre- register may delay your access into the DOT Headquarters building. Additionally, if you are attending in-person, arrive early to allow time for security checks necessary to access the building. Conference call-in and ``live meeting'' capability will be provided for both meetings. Specific information on call-in and live meeting access will be posted when available at https://www.phmsa.dot.gov/ hazmat/regs/international under ``Upcoming Events'' and at https:// www.osha.gov/dsg/hazcom/.

We propose to adopt a new airworthiness directive (AD) for all Airbus Model A318-111, and -112 airplanes, Model A319-111, -112, -113, -114, and -115 airplanes, Model A320-211, -212 and -214 airplanes, and Model A321-111, -112, -211, -212, and -213 airplanes. This proposed AD was prompted by a report of a production quality deficiency on the inner retainer installed on link assemblies of the engine mount, which could result in failure of the retainer. This proposed AD would require an inspection for, and replacement of, all non-conforming aft engine mount retainers. We are proposing this AD to detect and correct non- conforming retainers of the aft engine mount. This condition could result in the loss of the locking feature of the nuts of the inner and outer pins; loss of the pins will result in the aft mount engine link no longer being secured to the aft engine mount, possibly resulting in damage to the airplane and injury to persons on the ground.

We are adopting a new airworthiness directive (AD) for Turbomeca S.A. Arriel 1D and 1D1 turboshaft engines with a pre- modification (mod) TU357 gas generator module (M03), installed. This AD requires removing the pre-modification (mod) TU357 gas generator module (M03) and replacing with a part eligible for installation. This AD was prompted by reports of divergent rubbing between the piston shaft small diameter labyrinth and the rear bearing support. We are issuing this AD to prevent failure of the labyrinth seal and engine, in-flight shutdown, and loss of control of the helicopter.

This action establishes Class E airspace in Lisbon, ND. Controlled airspace is necessary to accommodate new Area Navigation (RNAV) Standard Instrument Approach Procedures at Lisbon Municipal Airport. The FAA is taking this action to enhance the safety and management of Instrument Flight Rule (IFR) operations at the airport.

The FAA proposes to rule and invites public comment on the release of land at The Eastern Iowa Airport, Cedar Rapids, Iowa, under the provisions of 49 U.S.C. 47107(h)(2).

The Department of Transportation (``Department,'' ``DOT,'' or ``we'') announces its intention to continue the ACACP as a discretionary Federal advisory committee in the event that the authority for the Committee under section 411 of the FAA Modernization and Reform Act of 2012 (Pub. L. 112-95, 126 Stat. 11), as amended, is not extended by Congress through legislation. The current authorization is set to expire on July 15, 2016. The Department is soliciting applications and nominations for new members of the Committee.

We propose special conditions for the BHTI Model 525 helicopter. This helicopter will have a novel or unusual design feature associated with fly-by-wire flight control system (FBW FCS) functions that affect the structural integrity of the rotorcraft. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

We propose to adopt a new airworthiness directive (AD) for Robinson Helicopter Company (Robinson) Model R44, R44 II, and R66 helicopters. This proposed AD would require a visual inspection of the main rotor blade (MRB) and either removing or altering it. This proposed AD is prompted by a report that a fatigue crack was found at an MRB's trailing edge and a determination that some MRBs may have reduced blade thickness due to blending out corrosion. The proposed actions are intended to prevent an MRB fatigue crack, which could lead to MRB failure and subsequent loss of helicopter control.

In accordance with the procedures governing the application for, and the processing of, special permits from the Department of Transportation's Hazardous Material Regulations (49 CFR part 107, Subpart B), notice is hereby given of the actions on special permits applications in (October to October 2014). The mode of transportation involved are identified by a number in the ``Nature of Application'' portion of the table below as follows: 1Motor vehicle, 2Rail freight, 3Cargo vessel, 4Cargo aircraft only, 5Passenger-carrying aircraft. Application numbers prefixed by the letters EE represent applications for Emergency Special Permits. It should be noted that some of the sections cited were those in effect at the time certain special permits were issued.

In accordance with the requirements of 49 U.S.C. 5117(c), PHMSA is publishing the following list of special permit applications that have been in process for 180 days or more. The reason(s) for delay and the expected completion date for action on each application is provided in association with each identified application.

The FAA is announcing a public meeting to gather additional technical input on the subject of installing an engine inlet barrier filter (IBF) on rotorcraft. Input gathered will aid in developing FAA guidance for evaluating engine IBFs installed on rotorcraft. Prior to the public meeting, the FAA previously sought public comments regarding the guidance online.

We propose to adopt a new airworthiness directive (AD) for certain Airbus Model A318-112 airplanes, A319-111, -112, -115, -132, and -133 airplanes, A320-214, -232, and -233 airplanes, and A321-211, - 212, -213, -231, and -232 airplanes. This proposed AD was prompted by a quality control review on the final assembly line, which determined that the wrong aluminum alloy was used to manufacture several structural parts. This proposed AD would require a one-time eddy current conductivity measurements of certain cabin and cargo compartment structural parts to determine if an incorrect aluminum alloy was used, and replacement if necessary. We are proposing this AD to detect and replace structural parts made of incorrect aluminum alloy. This condition could result in reduced structural integrity of the airplane.

The Surface Transportation Board (Board) is revising the heading to its CFR chapter, pursuant to the Surface Transportation Board Reauthorization Act of 2015.

We are adopting a new airworthiness directive (AD) for all Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes; Model CL-600-2D15 (Regional Jet Series 705) airplanes; Model CL-600-2D24 (Regional Jet Series 900) airplanes; and Model CL- 600-2E25 (Regional Jet Series 1000) airplanes. This AD requires a detailed visual inspection of the upper and lower engine pylons for protruding, loose, or missing fasteners; and repair, including applicable related investigative and corrective actions, if necessary. This AD was prompted by reports of loose or missing Hi-Lite fasteners on the upper and lower engine pylon structure common to the upper and lower pylon skin panels and engine thrust fitting. We are issuing this AD to detect and correct protruding, loose, or missing fasteners, which could result in structural failure of the engine pylons.

We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, and Model CL-600-2D24 (Regional Jet Series 900) airplanes. This AD was prompted by a report indicating that some operators have inadvertently removed the existing insulation blankets from the upper wing box area. This AD requires inspecting for and replacing missing insulation blankets in the upper wing box area. We are issuing this AD to detect and replace missing insulation blankets from the upper wing box area, which could result in inadequate thermal protection to prevent fuel ignition in the event of an undetected bleed-air leak due to a cracked or ruptured bleed-air duct.

We are adopting a new airworthiness directive (AD) for all Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This AD was prompted by accomplishment of a taxi-out checklist which revealed that the elevator movement was partially obstructed due to rotation of the flight control lock adjuster bracket. This AD requires a one-time inspection of the elevator tension control regulator for discrepancies, and corrective actions if necessary. We are issuing this AD to detect and correct discrepancies of the elevator tension control regulators. Such a condition could result in jamming of the elevator mechanism and consequent reduced controllability of the airplane.

As authorized by 46 U.S.C. 12121, the Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to grant waivers of the U.S.-build requirement of the coastwise laws under certain circumstances. A request for such a waiver has been received by MARAD. The vessel, and a brief description of the proposed service, is listed below.

As authorized by 46 U.S.C. 12121, the Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to grant waivers of the U.S.-build requirement of the coastwise laws under certain circumstances. A request for such a waiver has been received by MARAD. The vessel, and a brief description of the proposed service, is listed below.

Effective immediately, the membership of the PRB and ERB is as follows: