Department of Transportation 2009 – Federal Register Recent Federal Regulation Documents
Results 1,101 - 1,150 of 2,738
Airworthiness Directives; BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Saab AB, Saab Aerosystems Model SAAB 340A (SAAB/SF340A) and SAAB 340B Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800, and -900 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 737-600, -700, -700C, -800, and -900 series airplanes. That AD currently requires replacing brackets that hold the P5 panel to the airplane structure, the standby compass bracket assembly, the generator drive and standby power module, and the air conditioning module, as applicable. The existing AD also currently requires, among other actions, inspecting for wire length and for damage of the connectors and the wire bundles, and doing applicable corrective actions if necessary. This new AD requires an additional operational test of the P5-14 panel. This AD results from a report of an electrical burning smell in the flight compartment. We are issuing this AD to prevent wire bundles from contacting the overhead dripshield panel and modules in the P5 overhead panel, which could result in electrical arcing and shorting of the electrical connector and consequent loss of several critical systems essential for safe flight; and to ensure proper operation of the passenger oxygen system. If an improperly functioning passenger oxygen system goes undetected, the passenger oxygen mask could fail to deploy and result in possible incapacitation of passengers during a depressurization event.
18th Meeting: RTCA Special Committee 206/EUROCAE WG 76 Plenary
The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 206: Aeronautical Information Services and Meteorology Data Link Services
Airworthiness Directives; Honeywell International Inc. TPE331-10 and TPE331-11 Series Turboprop Engines
The FAA is adopting a new airworthiness directive (AD) for Honeywell International Inc. TPE331-10 and TPE331-11 series turboprop engines. This AD requires removing certain first stage turbine disks from service. This AD results from a report of an uncontained failure of a first stage turbine disk that had a metallurgical defect. We are issuing this AD to prevent uncontained failure of the first stage turbine disk and damage to the airplane.
Insurer Reporting Requirements; List of Insurers Required To File Reports
This document proposes to amend Appendices A, B and C of 49 CFR Part 544, Insurer Reporting Requirements. The appendices list those passenger motor vehicle insurers that are required to file reports on their motor vehicle theft loss experiences. An insurer included in any of these appendices would be required to file three copies of its report for the 2006 calendar year before October 25, 2009. If the passenger motor vehicle insurers remain listed, they must submit reports by each subsequent October 25. We are proposing to add and remove several insurers from relevant appendices.
Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; Toyota
This document grants in full the petition of Toyota Motor North America, Inc's., (Toyota) petition for an exemption of the Camry vehicle line in accordance with 49 CFR Part 543, Exemption from the Theft Prevention Standard. This petition is granted because the agency has determined that the antitheft device to be placed on the line as standard equipment is likely to be as effective in reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of the Theft Prevention Standard (49 CFR Part 541).
Qualification of Drivers; Exemption Applications; Diabetes
FMCSA announces receipt of applications from 24 individuals for exemptions from the prohibition against persons with insulin- treated diabetes mellitus (ITDM) operating commercial motor vehicles (CMVs) in interstate commerce. If granted, the exemptions would enable these individuals with ITDM to operate commercial motor vehicles in interstate commerce.
Information Collection
On September 4, 2008, as required by the Paperwork Reduction Act of 1995, the Pipeline and Hazardous Materials Safety Administration (PHMSA) published a notice in the Federal Register of its intent to revise the agency's standardized forms for reporting pipeline incidents and accidents. PHMSA later extended the time for responding to that notice until December 12, 2008, and received timely comments from several pipeline operators, five trade associations representing pipeline operators, the association representing State pipeline safety regulators, two State pipeline regulatory agencies, and one public interest group. PHMSA is publishing this notice to respond to comments, provide the public with an additional 30 days to comment on the proposed revisions to the incident and accident report forms, including the form instructions, and announce that the revised Information Collections will be submitted to the Office of Management and Budget (OMB) for approval.
Bridge Safety Standards
FRA is proposing to standardize and establish Federal requirements for railroad bridges. This proposed rule would require track owners to implement bridge management programs that include annual inspections of railroad bridges. The proposed rule would also require track owners to know the safe capacity load of bridges and to conduct special inspections if the weather or other conditions warrant such inspections. Finally, the proposed rule would also require the audit of the bridge management programs and the inspections.
Certification of Turbojets
This action proposes to enhance safety by amending the applicable standards for part 23 turbojet-powered airplaneswhich are commonly referred to as ``turbojets''to reflect the current needs of
Railroad Safety Advisory Committee (RSAC); Working Group Activity Update
The FRA is updating its announcement of RSAC's Working Group activities to reflect its current status.
Airworthiness Directives; Cessna Aircraft Company 150 and 152 Series Airplanes
We propose to revise Airworthiness Directive (AD) 2009-10-09, which applies to certain Cessna Aircraft Company (Cessna) 150 and 152 series airplanes. AD 2009-10-09 requires either installing a placard prohibiting spins and other acrobatic maneuvers in the airplane or replacing the rudder stop, the rudder stop bumper, and the attachment hardware with a new rudder stop modification kit and replacing the safety wire with jamnuts. Since we issued AD 2009-10-09, we became aware of a need to clarify certain model and serial number designations, remove the duplicate requirement of replacing the safety wire with jamnuts, and clarify the conditional acceptability of using Modification Kit part number (P/N) SK152-25 as a terminating action to this proposed AD. Consequently, this proposed AD would retain the actions currently required in AD 2009-10-09, correct model designation for certain serial numbers, remove the duplicate requirement of replacing safety wire with jamnuts, and clarify the conditional acceptability of using Modification Kit P/N SK152-25 as a terminating action to this proposed AD. We are proposing this AD to prevent the rudder from traveling past the normal travel limit. Operation in this non-certificated control position is unacceptable and could cause undesirable consequences, such as contact between the rudder and the elevator.
List of Nonconforming Vehicles Decided To Be Eligible for Importation
This document revises the list of vehicles not originally manufactured to conform to the Federal motor vehicle safety standards (FMVSS) that NHTSA has decided to be eligible for importation. This list is published in an appendix to the agency's regulations that prescribe procedures for import eligibility decisions. The list has been revised to add all vehicles that NHTSA has decided to be eligible for importation since October 1, 2008, and to remove all previously listed vehicles that are now more than 25 years old and need no longer comply with all applicable FMVSS to be lawfully imported. NHTSA is required by statute to publish this list annually in the Federal Register.
Delegations of Authority
This document amends NHTSA's delegations of authority. The amendment effectuates an adjustment that will enable NHTSA to achieve its mission more effectively and efficiently.
Agency Information Collection Activity Seeking OMB Approval
The FAA invites public comments about our intention to request the Office of Management and Budget's (OMB) revision of a current information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on June 5, 2009, 74 FR 27058-27059. Wildlife strike data are collected to develop standards and monitor hazards to aviation. Data identify wildlife strike control requirements and provide in-service data on aircraft component failure.
Airworthiness Directives; American Champion Aircraft Corp. Models 7ECA, 7GCAA, 7GCBC, 7KCAB, 8KCAB, and 8GCBC Airplanes
We propose to adopt a new airworthiness directive (AD) for all American Champion Aircraft Corp. Models 7ECA, 7GCAA, 7GCBC, 7KCAB, 8KCAB, and 8GCBC airplanes, manufactured prior to 1989 and equipped with folding rear seat backs. This proposed AD would require inspection of the rear seat back hinge areas for cracking and excessive elongation of the rear seat hinge bolt hole and, if cracking or excessive elongation is found, replacement of the rear seat frame. This proposed AD results from an occurrence of the rear seat hinge area failing in flight. We are proposing this AD to detect and correct cracking of the rear seat back hinge area and excessive elongation of the rear seat hinge bolt hole, either of which could result in failure of the seat back. This failure could lead to a rear-seated pilot or passenger inadvertently interfering with the control stick while attempting to not roll to the rear of the airplane upon seat back failure. Consequently, this failure could result in loss of control.
Airworthiness Directives; Bombardier Model DHC-8-100 and DHC-8-200 Series Airplanes, and Model DHC-8-301, -311, and -315 Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier Model DHC-8-100 and DHC-8-200 series airplanes, and DHC-8-301, -311, and -315 airplanes. This proposed AD would require implementing a corrosion prevention and control program (CPCP) either by accomplishing specific tasks or by revising the maintenance inspection program to include a CPCP. This proposed AD results from the determination that, as airplanes age, they are more likely to exhibit indications of corrosion. We are proposing this AD to prevent structural failure of the airplane due to corrosion.
Airworthiness Directives; Airbus Model A318 Series Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Federal Motor Vehicle Safety Standards; Controls, Telltales and Indicators
In an August 2005 final rule, we updated our standard regulating motor vehicle controls, telltales and indicators. The standard specifies requirements for the location, identification, and illumination of these items. In May 2006, we published a response to four petitions for reconsideration, including one asking us to reconsider a requirement for color contrast between identifiers and their backgrounds. We denied this petition for reconsideration.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Think Technology AS; Grant of Application for a Temporary Exemption From the Advanced Air Bag Requirements of Federal Motor Vehicle Safety Standard No. 208
This document grants the Think Technology AS (Think) application for a temporary exemption from certain advanced air bag requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 208, Occupant Crash Protection. The exemption applies to the Think City EV vehicle line. In accordance with 49 CFR Part 555, the basis for the grant is that the exemption would make the development or field evaluation of a low-emission vehicle easier and would not unreasonably lower the safety or impact protection level of that vehicle. The exemption is effective from February 1, 2010 through January 31, 2012.
Administrative Wage Garnishment
This final rule will implement the authority established under the Debt Collection Improvement Act of 1996 (DCIA) for DOT to collect the Department's past due indebtedness through administrative wage garnishment. The final rule will adopt, without change, the hearing procedures issued by the Department of the Treasury implementing administrative wage garnishment under the DCIA. This final rule would apply only to individuals who are not Federal employees. The final rule also will amend regulations on procedures for the collection of claims to conform DOT regulations to applicable provisions of the DCIA.
Fiscal Year 2010 Safety Grants
This notice is to inform the public of FMCSA's Fiscal Year (FY) 2010 safety grant opportunities and FMCSA's changes to its application and award processes for grant programs. The Agency instituted procedural changes in an effort to simplify and streamline its grants application and award processes. The 11 safety programs include the Motor Carrier Safety Assistance Program (MCSAP) Basic grants; MCSAP Incentive grants; MCSAP New Entrant Safety Audit grants; MCSAP High Priority grants; Commercial Motor Vehicle (CMV) Operator Safety Training grants; Border Enforcement grants (BEG); Commercial Driver's License Program Improvement (CDLPI) grants; Commercial Driver's License Information System (CDLIS) Modernization grants; Performance and Registration Information Systems Management (PRISM) grants; Safety Data Improvement Program grants (SaDIP); and the Commercial Vehicle Information Systems and Networks (CVISN) grants. Each grant program was provided for in the Agency's most recent authorization, the Safe, Accountable, Flexible, Efficient Transportation Equity Act: A Legacy for Users (SAFETEA-LU). The purpose of this notice is to provide grantees with information on the Agency's FY 2010 safety grant application deadlines.
Airworthiness Directives; McDonnell Douglas Model DC-9-30, DC-9-40, and DC-9-50 Series Airplanes
We propose to adopt a new airworthiness directive (AD) for certain McDonnell Douglas Model DC-9-30, DC-9-40, and DC-9-50 series airplanes. This proposed AD would require inspecting to determine the part numbers of the forward and aft auxiliary tank fuel boost and transfer pump conduit/conduit assembly and conduit assembly electrical connector, as applicable, and corrective actions if necessary. This proposed AD results from fuel system reviews conducted by the manufacturer. We are proposing this AD to detect and correct the potential for an arc/spark condition to occur within the fuel boost or transfer pump conduit assembly connectors and propagate into the forward and aft auxiliary fuel tanks, which could result in a fire or explosion.
Airworthiness Directives; Boeing Model 747-200C and -200F Series Airplanes
The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Boeing Model 747-200C and -200F series airplanes. The existing AD currently requires repetitive inspections to find fatigue cracking in the floor panel attachment fastener holes of the upper chord of certain upper deck floor beams in Section 41 (i.e., body station 520 and forward), and repair if necessary. The existing AD also provides optional modifications, which extend the threshold for the initiation of certain repetitive inspections. This proposed AD would add repetitive inspections to find fatigue cracking in the floor panel attachment fastener holes of the upper chord of certain other upper deck floor beams in Section 41 and Section 42 (i.e., aft of body station 520); repetitive inspections to find fatigue cracking in the permanent fastener holes of the upper chord of certain upper deck floor beams in Section 41; and related investigative and corrective actions. This proposed AD would also provide a new optional modification, which would terminate certain repetitive inspections. This proposed AD results from new reports of cracking in the upper chord of the upper deck floor beams in Sections 41 and 42, and new analysis that shows the permanent fastener holes of the upper chord of certain upper deck floor beams in Section 41 are also susceptible to fatigue cracking. We are proposing this AD to detect and correct cracking in the upper chord of the upper deck floor beams. Such cracking could extend and sever the floor beams, which could result in rapid decompression and loss of controllability of the airplane.
Airworthiness Directives; Saab AB, Saab Aerosystems Model SAAB 340A (SAAB/SF340A) and SAAB 340B Airplanes
We are revising an earlier NPRM for the products listed above. This action revises the earlier NPRM by expanding the scope. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Proposed Amendment of Class E Airspace; Midlothian-Waxahachie, TX
This action proposes to amend Class E airspace at Midlothian- Waxahachie, TX. Additional controlled airspace is necessary to accommodate new Standard Instrument Approach Procedures (SIAPs) at Mid- Way Regional Airport, Midlothian-Waxahachie, TX. This action would also reflect the name change to Mid-Way Regional Airport and update the geographic coordinates. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations for SIAPs at Mid-Way Regional Airport.
Proposed Revision of Class E Airspace; Noorvik, AK
This action proposes to establish Class E airspace at the Robert (Bob) Curtis Memorial Airport at Noorvik, AK. Two Standard Instrument Approach Procedures (SIAPs) are being developed for the Robert (Bob) Curtis Memorial Airport at Noorvik, AK. Additionally, one textual Obstacle Departure Procedure (ODP) is being developed. Adoption of this proposal would result in establishing Class E airspace upward from 700 feet (ft.) above the surface at the Robert (Bob) Curtis Memorial Airport at Noorvik, AK.
Special Conditions: Boeing Model 747-8/-8F Airplanes; Additional Airframe Structural Design Requirements Related to Sudden Engine Stoppage Due to Fan Blade Failures
These special conditions are issued for Boeing Model 747-8/-8F airplanes. These airplanes will have a novel or unusual design feature(s) associated with an increased engine size when compared to previous model airplanes. These larger engines with larger bypass fans are capable of producing higher and more complex dynamic loads than previously experienced in older designs. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Special Conditions: Boeing Model 747-8/-8F Airplanes; Interaction of Systems and Structures
These special conditions are issued for the Boeing Model 747- 8/-8F airplanes. These airplanes will have a novel or unusual design feature(s) that will affect structural performance. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Airworthiness Directives; Short Brothers Model SD3-60 Airplanes
We are revising an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Notice of Intent To Rule on Request To Release Airport Property at the Seattle-Tacoma International Airport, Seattle, WA
The FAA proposes to rule and invite public comment on the release of land at the Seattle-Tacoma International Airport under the provisions of section 125 of the Wendell H. Ford Aviation Investment Reform Act for the 21st Century (AIR 21).
IFR Altitudes; Miscellaneous Amendments
This amendment adopts miscellaneous amendments to the required IFR (instrument flight rules) altitudes and changeover points for certain Federal airways, jet routes, or direct routes for which a minimum or maximum en route authorized IFR altitude is prescribed. This regulatory action is needed because of changes occurring in the National Airspace System. These changes are designed to provide for the safe and efficient use of the navigable airspace under instrument conditions in the affected areas.
Office of Hazardous Materials Safety; Notice of Application for Special Permits
In accordance with the procedures governing the application for, and the processing of, special permits from the Department of Transportation's Hazardous Material Regulations (49 CFR Part 107, Subpart B), notice is hereby given that the Office of Hazardous Materials Safety has received the application described herein. Each mode of transportation for which a particular special permit is requested is indicated by a number in the ``Nature of Application'' portion of the table below as follows: 1Motor vehicle, 2Rail freight, 3Cargo vessel, 4Cargo aircraft only, 5Passenger-carrying aircraft.
Office of Hazardous Materials Safety; Notice of Applications for Modification of Special Permit
In accordance with the procedures governing the application for, and the processing of, special permits from the Department of Transportation's Hazardous Material Regulations (49 CFR Part 107, Subpart B), notice is hereby given that the Office of Hazardous Materials Safety has received the applications described herein. This notice is abbreviated to expedite docketing and public notice. Because the sections affected, modes of transportation, and the nature of application have been shown in earlier Federal Register publications, they are not repeated here. Requests for modification of special permits (e.g., to provide for additional hazardous materials, packaging design changes, additional mode of transportation, etc.) are described in footnotes to the application number. Application numbers with the suffix ``M'' denote a modification request. These applications have been separated from the new application for special permits to facilitate processing.
Motor Carrier Safety Advisory Committee Public Meeting
FMCSA announces that the Motor Carrier Safety Advisory Committee (MCSAC) will hold a committee meeting. The meeting is open to the public.
Agency Information Collection Activity Under OMB Review
The Federal Transit Administration invites public comment about our intention to request the Office of Management and Budget's (OMB) approval to renew the following information collection: Tribal Transit Program (OMB Number: 2132-0567). The information to be collected for this program is to ensure FTA's compliance with applicable Federal laws and the Common Grant Rule. The Federal Register Notice with a 60-day comment period soliciting comments was published on May 13, 2009.
Petitions for Exemption; Summary of Petitions Received
This notice contains a summary of certain petitions seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of any petition or its final disposition.
Petitions for Exemption; Summary of Petitions Received
This notice contains a summary of certain petitions seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of any petition or its final disposition.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
