2006 – Federal Register Recent Federal Regulation Documents

Results 3,451 - 3,500 of 6,163
Change of Official Office of Pollution Prevention and Toxics' Mailing Address; Technical Amendments
Document Number: E6-9078
Type: Rule
Date: 2006-06-12
Agency: Environmental Protection Agency
EPA's Office of Pollution Prevention and Toxics (OPPT) has discovered an error in the mailing address that appears in certain sections of 40 CFR chapter I, subchapter R. By these technical amendments, OPPT corrects those errors.
Airworthiness Directives; McDonnell Douglas Model DC-10-10 and DC-10-10F Airplanes; and Model MD-10-10F Airplanes
Document Number: E6-9063
Type: Proposed Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for certain McDonnell Douglas Model DC-10-10 and DC-10-10F airplanes; and Model MD-10-10F airplanes. This proposed AD would require replacing the clamp bases for the fuel vent pipe with improved clamp bases. This proposed AD results from reports that the foil wrapping on existing plastic clamp bases has migrated out of position, which compromises the bonding of the fuel vent pipes to the airplane structure. We are proposing this AD to ensure that the fuel vent pipes are properly bonded to the airplane structure. Improper bonding could prevent electrical energy from a lightning strike from dissipating to the airplane structure, and create an ignition source, which could result in a fuel tank explosion.
Airworthiness Directives; Airbus Model A318, A319, A320, and A321 Airplanes
Document Number: E6-9062
Type: Proposed Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to supersede an existing airworthiness directive (AD) that applies to all Airbus Model A318, A319, A320, and A321 airplanes. The existing AD currently requires a one-time inspection to determine the serial number of both main landing gear (MLG) sliding tubes, repetitive detailed inspections for cracking of the affected MLG sliding tubes, and corrective actions if necessary. This proposed AD would retain these inspections and add new repetitive inspections for cracking of the MLG sliding tubes. This proposed AD would also require eventual replacement of both MLG shock absorbers. Doing this replacement would terminate the repetitive inspection requirements of this proposed AD. This proposed AD results from a determination that additional inspections and mandatory replacement of the MLG shock absorbers are necessary. We are proposing this AD to detect and correct cracking in an MLG sliding tube, which could result in failure of the sliding tube, loss of one axle, and consequent reduced controllability of the airplane.
Airworthiness Directives; Airbus Model A319, A320, and A321 Airplanes
Document Number: E6-9061
Type: Proposed Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus Model A319, A320, and A321 airplanes. This proposed AD would require an inspection to determine if the stiff part of the girt and girt bar position of the forward left-hand and right-hand passenger doors is incorrect, and repair if necessary. This proposed AD results from cases of girt bar disengagement from the floor fitting during deployment tests of slide rafts at the forward passenger doors. We are proposing this AD to prevent disengagement of the telescopic girt bar from the airplane when the door is opened in emergency situations, which could result in the inability to open the passenger door and to use the escape slide/raft at that door during an emergency evacuation of the airplane.
Suspension of Community Eligibility
Document Number: E6-9051
Type: Rule
Date: 2006-06-12
Agency: Federal Emergency Management Agency, Department of Homeland Security
This rule identifies communities, where the sale of flood insurance has been authorized under the National Flood Insurance Program (NFIP), that are scheduled for suspension on the effective dates listed within this rule because of noncompliance with the floodplain management requirements of the program. If FEMA receives documentation that the community has adopted the required floodplain management measures prior to the effective suspension date given in this rule, the suspension will not occur and a notice of this will be provided by publication in the Federal Register on a subsequent date.
Consultation on Classification on Standards and Definitions
Document Number: E6-9044
Type: Proposed Rule
Date: 2006-06-12
Agency: National Indian Gaming Commission, Department of the Interior
The purpose of this document is to publish the schedule for government-to-government consultation on proposed revisions to 25 CFR part 502 and new part 546.
Implementation of Unilateral Chemical/Biological (CB) Controls on Certain Biological Agents and Toxins; Clarification of Controls on Medical Products Containing Certain Toxins on the Australia Group (AG) Common Control Lists; Additions to the List of States Parties to the Chemical Weapons Convention (CWC)
Document Number: E6-8995
Type: Rule
Date: 2006-06-12
Agency: Department of Commerce, Bureau of Industry and Security, Industry and Security Bureau
The Bureau of Industry and Security (BIS) is publishing this final rule to amend the Export Administration Regulations (EAR) to expand export and reexport controls on certain biological agents and toxins (referred to, herein, as ``select agents and toxins'') that have been determined by the Centers for Disease Control and Prevention (CDC), U.S. Department of Health and Human Services, and the Animal and Plant Health Inspection Service (APHIS), U.S. Department of Agriculture, to have the potential to pose a severe threat to human, animal and plant life, as well as certain sectors of the U.S. economy (e.g., agriculture). Prior to the publication of this rule, twenty-two of these agents were not listed on the Commerce Control List (CCL) and one of these agents was incompletely specified therein. By amending the EAR to add a new CCL entry that controls CDC and/or APHIS select agents and toxins (including associated genetic elements, recombinant nucleic acids, and recombinant organisms) not previously specified on the CCL, this rule complements the controls that CDC and AHPIS have imposed on the possession, use, and transfer of these select agents and toxins within the United States. The addition of these items to the CCL is expected to have a minimal impact on U.S. industry, since the volume of exports and reexports is extremely limited. This rule also amends the EAR to clarify controls on certain medical products containing AG-controlled toxins, other than ricin or saxitoxin, by revising the definition of such products to clearly indicate that they include pharmaceutical formulations, prepackaged for distribution as clinical or medical products, that have been approved by the Food and Drug Administration (FDA) for use as an ``Investigational New Drug'' (IND). Specifically, this rule clarifies that FDA-approved IND products containing AG-controlled toxins (except ricin or saxitoxin) are considered to be ``medical products'' as described in the CCL entry that controls vaccines, immunotoxins, medical products, and diagnostic and food testing kits. BIS is making this clarification because the previous revision to the definition of medical products inadvertently failed to specify that such products include IND items. Furthermore, this clarification is consistent with the language in the AG exemption for clinical and medical products containing botulinum toxins and conotoxins, since the AG exemption applies when such products are designed for ``testing,'' as well as human administration, in the treatment of medical conditions. In addition, this rule removes the license requirements for exports and reexports to St. Kitts and Nevis of items that require a license for export or reexport only to countries of concern for chemical and biological weapons proliferation (CB) reasons. This change is being made because St. Kitts and Nevis is not listed in Country Group D:3. As a result of this change, there is now a one-to-one correspondence between the countries included in Country Group D:3 and the countries for which a license requirement is indicated under CB Column 3 of the Commerce Country Chart. Finally, this rule updates the list of countries that currently are States Parties to the Chemical Weapons Convention (CWC) by adding Antigua and Barbuda, Bhutan, Cambodia, the Democratic Republic of the Congo, Djibouti, Grenada, Haiti, Honduras, Liberia, and Vanuatu, which recently became States Parties. As a result of this change, the CW (Chemical Weapons) license requirements and policies in the EAR that apply to these countries now conform with those applicable to other CWC States Parties.
Proposed Flood Elevation Determinations
Document Number: 06-5309
Type: Proposed Rule
Date: 2006-06-12
Agency: Federal Emergency Management Agency, Department of Homeland Security
Technical information or comments are requested on the proposed Base (1% annual chance) Flood Elevations (BFEs) and proposed BFE modifications for the communities listed below. The BFEs are the basis for the floodplain management measures that the community is required either to adopt or to show evidence of being already in effect in order to qualify or remain qualified for participation in the National Flood Insurance Program (NFIP).
Establishment of Class E Airspace; St. Joseph Medical Center, Maryland
Document Number: 06-5308
Type: Proposed Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
This notice proposes to establish Class E airspace at St. Joseph Medical Center, Towson, Maryland. The development of an Area Navigation (RNAV), Standard instrument Approach Procedures (SIAP) and Helicopter RNAV (GPS) 269 approach for the St. Joseph Medical Center to serve flights operating into the airport during Instrument Flight Rules (IFR) conditions makes this action necessary. Controlled airspace extending upward from 700 feet Above Ground Level (AGL) is needed to contain aircraft executing an approach. The area would be depicted on aeronautical charts for pilot reference.
Establishment of Class E Airspace; Hill Top Heliport, Troy, PA
Document Number: 06-5307
Type: Proposed Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
This notice proposes to establish Class E airspace at Hill Top Heliport, Troy, PA. The development of an Area Navigation (RNAV), Standard Instrument Approach Procedures (SIAP) and Helicopter RNAV (GPS) 186 approach for the Hill Top Heliport to serve flights operating into the airport during Instrument Flight Rules (IFR) conditions makes this action necessary. Controlled airspace extending upward from 700 feed Above Ground Level (AGL) is needed to contain aircraft executing an approach. The area would be depicted on aeronautical charts for pilot reference.
Establishment of Class E Airspace; Robert Packer Hospital, Sayre, PA
Document Number: 06-5306
Type: Proposed Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
This notice proposes to establish Class E airspace at Robert Packer Hospital, Sayre, PA. The development of an Area Navigation (RNAV) Standard Instrument Approach Procedure (SIAP) and Helicopter RNAV (GPS) 135 approach for the Robert Packer Hospital to serve flights operating into the airport during Instrument Flight Rules (IFR) conditions makes this action necessary. Controlled airspace extending upward from 700 feet Above Ground Level (AGL) is needed to contain aircraft executing an approach. The area would be depicted on aeronautical charts for pilot reference.
Approval and Promulgation of Air Quality Implementation Plans; Indiana
Document Number: 06-5252
Type: Rule
Date: 2006-06-12
Agency: Environmental Protection Agency
EPA is approving revisions to the Indiana State Implementation Plan (SIP) for ozone. In these revisions, the State has incorporated changes EPA made to its definition of volatile organic compound (VOC) and its list of Hazardous Air Pollutants (HAP). As a result of EPA's approval, five chemical compounds will no longer be considered VOCs and one compound will no longer be considered a HAP under Indiana's SIP.
Approval and Promulgation of Air Quality Implementation Plans; Indiana
Document Number: 06-5251
Type: Proposed Rule
Date: 2006-06-12
Agency: Environmental Protection Agency
EPA is proposing to approve revisions to the Indiana State Implementation Plan (SIP) for ozone. The state is adding four chemical compounds to its list of compounds that are now exempt from being considered a volatile organic compound (VOC). Indiana also is removing a compound from the list of hazardous air pollutants (HAP). The revisions Indiana made parallel the changes EPA made to our VOC definitions and HAP list on November 29, 2004 and that became effective on December 29, 2004. Four VOCs were found by EPA to make a negligible contribution to tropospheric ozone formation. The compounds are: 1,1,1,2,2,3,3- heptafluoro-3-methoxy-propane, 3-ethoxy-1,1,1,2,3,4,4,5,5,6,6,6- dodecafluoro-2-(trifluoromethyl)hexane, 1,1,1,2,3,3,3- heptafluoropropane, and methyl formate. Companies producing or using the four compounds will no longer need to follow the VOC rules for these compounds. The requirements for t-butyl acetate are also modified. It is not considered a VOC for emission limits and content requirements. T-butyl acetate will still be considered a VOC for the recordkeeping, emissions reporting, and inventory requirements. Indiana is removing ethylene glycol monobutyl ether (EGBE) (2- Butoxyethanol) from its HAP list, too. EGBE will no longer be considered a hazardous air pollutant.
Approval and Promulgation of Implementation Plans; State of Missouri
Document Number: 06-5250
Type: Rule
Date: 2006-06-12
Agency: Environmental Protection Agency
EPA is approving a revision to the Missouri State Implementation Plan (SIP). This approval pertains to revisions to the state's rule which restricts emissions from specific Missouri lead smelter-refinery installations. The effect of this approval is to remove duplication between two SIP-approved documents, and does not affect the stringency of the requirements.
Approval and Promulgation of Implementation Plans; State of Missouri
Document Number: 06-5249
Type: Proposed Rule
Date: 2006-06-12
Agency: Environmental Protection Agency
EPA is approving a revision to the Missouri State Implementation Plan (SIP). This approval pertains to revisions to the state's rule which restricts emissions from specific Missouri lead smelter-refinery installations. The effect of this approval is to remove duplication between two SIP-approved documents, and does not affect the stringency of the requirements.
Airworthiness Directives; Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
Document Number: 06-5246
Type: Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
This document corrects a typographical error that appeared in AD 2006-10-01 that was published in the Federal Register on May 8, 2006 (71 FR 26682). The typographical error resulted in an incorrect revision date for a referenced service bulletin. This AD is applicable to certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD requires the installation of protective tape on the fire and overheat control unit in the flight compartment, and repetitive inspections of the condition of the protective tape and related corrective action. This AD also mandates eventual replacement of the existing fire and overheat control unit with a modified unit, which ends the repetitive inspections.
Airworthiness Directives; Eurocopter France Model EC130 B4 Helicopters
Document Number: 06-5241
Type: Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
This amendment adopts a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model EC130 B4 helicopters. This action requires inspecting the throttle twist grip (twist grip) assembly for any foreign body (chip or debris), any rotating micro-switch, and any micro-switch roller that does not move freely. If any unairworthy condition is found, this action requires that it be corrected before further flight. This amendment is prompted by two reports of a twist grip assembly jamming in the ``IDLE'' position. The actions specified in this AD are intended to detect and prevent jamming of the twist grip assembly, which, if present, could keep the engine from operating above idle speed and result in subsequent loss of control of the engine power of the helicopter.
Airworthiness Directives; Boeing Model 767-200 and -300 Series Airplanes
Document Number: 06-5210
Type: Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
The FAA is revising an existing airworthiness directive (AD) that applies to certain Boeing Model 767-200 and -300 series airplanes. That AD currently requires repetitive inspections to detect wear or damage of the door latches and disconnect housings in the off-wing escape slide compartments, and replacement of any discrepant component with a new component. This new AD revises the applicability of the existing AD to refer to a later revision of the referenced service bulletin, which removes airplanes that are not subject to the identified unsafe condition. This AD results from reports of worn and damaged door latches and disconnect housings in the off-wing escape slide compartments. We are issuing this AD to ensure deployment of an escape slide during an emergency evacuation. Non-deployment of an escape slide during an emergency could slow down the evacuation of the airplane and result in injury to passengers or flightcrew. We are also issuing this AD to detect damaged disconnect housings in the off-wing escape slide compartments, which could result in unexpected deployment of an escape slide during maintenance, and consequent injury to maintenance personnel.
Airworthiness Directives; Boeing Model 747-400 Series Airplanes
Document Number: 06-5209
Type: Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-400 series airplanes. This AD requires inspecting the support bracket of the crew oxygen cylinder installation to determine the manufacturing date marked on the support, and performing corrective action if necessary. This AD results from a report indicating that certain oxygen cylinder supports may not have been properly heat-treated. We are issuing this AD to prevent failure of the oxygen cylinder support under the most critical flight load conditions, which could cause the oxygen cylinder to come loose and leak oxygen. Leakage of oxygen could result in oxygen being unavailable for the flightcrew or could result in a fire hazard in the vicinity of the leakage.
Airworthiness Directives; Goodrich Evacuation Systems Approved Under Technical Standard Order (TSO) TSO-C69b and Installed on Airbus Model A330-200 and -300 Series Airplanes, Model A340-200 and -300 Series Airplanes, and Model A340-541 and -642 Airplanes
Document Number: 06-5208
Type: Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for Goodrich evacuation systems approved under TSO-C69b and installed on certain Airbus Model A330-200 and -300 series airplanes, Model A340-200 and -300 series airplanes, and Model A340-541 and -642 airplanes. This AD requires inspecting to determine the part number of the pressure relief valves on the affected Goodrich evacuation systems, and corrective action if necessary. This AD results from a report indicating that, during maintenance testing, the pressure relief valves on the affected Goodrich evacuation systems did not seal when activated, which caused the pressure in the escape slide/raft to drop below the minimum allowable raft mode pressure. We are issuing this AD to prevent loss of pressure in the escape slides/rafts after an emergency evacuation, which could result in inadequate buoyancy to support the raft's passenger capacity during ditching, and increase the chance for injury to raft passengers.
Airworthiness Directives; Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-300, 747-400, 747-400D, and 747SR Series Airplanes
Document Number: 06-5207
Type: Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 747-100 and -200 series airplanes. That AD currently requires repetitive inspections for cracking of the station 800 frame assembly, and repair if necessary. This new AD retains the repetitive inspection requirements of the existing AD, but expands the area to be inspected. This AD also reduces the initial inspection threshold, removes the adjustment of the compliance threshold and repetitive interval based on cabin differential pressure, and adds airplanes to the applicability. This AD results from several reports of cracks of the station 800 frame assembly on airplanes that had accumulated fewer total flight cycles than the initial inspection threshold in the existing AD. We are issuing this AD to detect and correct fatigue cracks that could extend and fully sever the frame, which could result in development of skin cracks that could lead to rapid depressurization of the airplane.
Airworthiness Directives; BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ Airplanes
Document Number: 06-5206
Type: Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding an existing airworthiness directive (AD), which applies to certain BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ airplanes. That AD currently requires one-time inspections of the inner webs and flanges at frames 15, 18, 41, and 43 for evidence of corrosion or cracking; and corrective actions if necessary. This new AD instead requires new repetitive inspections and expands the area to be inspected. This new AD also expands the applicability and provides an optional action that would extend the repetitive inspection interval. This AD results from a report indicating that in some cases the inspections required by the existing AD revealed no damage, yet frame corrosion and cracking were later found during scheduled maintenance in the two forward fuselage frames 15 and 18. We are issuing this AD to prevent reduced structural integrity of the airplane.
Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800, and -900 Series Airplanes
Document Number: 06-5205
Type: Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, -800, and -900 series airplanes. This AD requires replacing the fuel shutoff valve wires and conduit assemblies in the left and right engine strut aft fairing areas. This AD results from a report that an operator discovered many small chafe marks and exposed shield braid on fuel shutoff wires routed through a conduit in the wing. We are issuing this AD to prevent exposed wires that could provide an ignition source in a flammable leakage zone and possibly lead to an uncontrolled fire or explosion.
Endangered and Threatened Wildlife and Plants; Amended Designation of Critical Habitat for the Wintering Population of the Piping Plover
Document Number: 06-5192
Type: Proposed Rule
Date: 2006-06-12
Agency: Fish and Wildlife Service, Department of the Interior
We, the U.S. Fish and Wildlife Service (Service), propose to amend critical habitat for the wintering population of the piping plover (Charadrius melodus) in North Carolina under the Endangered Species Act of 1973, as amended (Act). In total, approximately 1,827 acres (ac) (739 hectares (ha)) fall within the boundaries of the proposed amended critical habitat designation, located in Dare and Hyde counties, North Carolina.
Hazardous Materials: Requirements for UN Cylinders
Document Number: 06-5182
Type: Rule
Date: 2006-06-12
Agency: Pipeline and Hazardous Materials Safety Administration, Department of Transportation
In this final rule, PHMSA is amending the Hazardous Materials Regulations (HMR) to adopt standards for the design, construction, maintenance and use of cylinders and multiple-element gas containers based on the standards contained in the United Nations Recommendations on the Transport of Dangerous Goods. Aligning the HMR with the international standards promotes greater flexibility, permits the use of advanced technology for the manufacture of pressure receptacles, provides for a broader selection of pressure receptacles, reduces the need for special permits, and facilitates international commerce in the transportation of compressed gases without sacrificing the current level of safety and without imposing undue burdens on the regulated community.
Airworthiness Directives; Airbus Model A300 B4-600R Series Airplanes, A300 C4-605R Variant F Airplanes, A300 F4-600R Series Airplanes; and Model A310-300 Series Airplanes
Document Number: 06-5124
Type: Rule
Date: 2006-06-12
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Airbus transport category airplanes. This AD requires replacing the existing vent float valve with a new, improved vent float valve. This AD results from reports of failure of the vent float valve in the left-hand outboard section of the trimmable horizontal stabilizer. We are issuing this AD to prevent, in the event of a lightning strike to the horizontal stabilizer, sparking of metal parts and debris from detached and damaged float valves, or a buildup of static electricity, which could result in ignition of fuel vapors and consequent fire or explosion.
Standards of Performance for Stationary Spark Ignition Internal Combustion Engines and National Emission Standards for Hazardous Air Pollutants for Reciprocating Internal Combustion Engines
Document Number: 06-4919
Type: Proposed Rule
Date: 2006-06-12
Agency: Environmental Protection Agency
EPA is proposing new source standards of performance for stationary spark ignition internal combustion engines. EPA is also proposing national emission standards for hazardous air pollutants for stationary reciprocating internal combustion engines that either are located at area sources of hazardous air pollutant emissions or that have a site rating of less than or equal to 500 brake horsepower and are located at major sources of hazardous air pollutant emissions.
Diesel Particulate Matter Exposure of Underground Metal and Nonmetal Miners
Document Number: E6-9067
Type: Rule
Date: 2006-06-09
Agency: Department of Labor, Mine Safety and Health Administration
The Mine Safety and Health Administration (MSHA) will conduct three outreach seminars to assist metal and nonmetal underground mine operators who use diesel-powered equipment in complying with the diesel particulate matter (DPM) health standards published on May 18, 2006 (71 FR 28924). The seminars will also address requirements for special extensions of time in which to meet the final limit.
Pipeline Safety: Update of Regulatory References to Technical Standards
Document Number: E6-9059
Type: Rule
Date: 2006-06-09
Agency: Pipeline and Hazardous Materials Safety Administration, Department of Transportation
This final rule updates the pipeline safety regulations to incorporate by reference all or parts of new editions of voluntary consensus technical standards to enable pipeline operators to utilize current technology, materials, and practices.
Fisheries of the Caribbean, Gulf of Mexico, and South Atlantic; Snapper-Grouper Fishery Off the Southern Atlantic States; Amendment 13C
Document Number: E6-9028
Type: Proposed Rule
Date: 2006-06-09
Agency: Department of Commerce, National Oceanic and Atmospheric Administration
NMFS issues this proposed rule to implement Amendment 13C to the Fishery Management Plan for the Snapper-Grouper Fishery of the South Atlantic Region (FMP), as prepared and submitted by the South Atlantic Fishery Management Council (Council). Amendment 13C proposes management measures to end overfishing of snowy grouper, golden tilefish, vermilion snapper, and black sea bass and measures to allow moderate increases in recreational and commercial harvest of red porgy consistent with the rebuilding program for that stock. For the commercial fisheries, this proposed rule would establish restrictive quotas for snowy grouper, golden tilefish, vermilion snapper, and black sea bass and, after the quotas are met, prohibit all purchase and sale of the applicable species and restrict all harvest and possession to the applicable bag limit; establish restrictive trip limits for snowy grouper and golden tilefish; require at least 2-inch (5.1-cm) mesh in the back panel of black sea bass pots; require black sea bass pots to be removed from the water after the quota is reached; change the fishing year for black sea bass; increase the trip limit for red porgy; establish a red porgy quota that would allow a moderate increase in harvest; and, after the red porgy quota is reached, prohibit all purchase and sale and restrict all harvest and possession to the bag limit. For the recreational fisheries, this proposed rule would reduce the bag limits for snowy grouper, golden tilefish, and black sea bass; increase the minimum size limit for vermilion snapper and black sea bass; change the fishing year for black sea bass; and increase the bag limit for red porgy. The intended effects of this proposed rule are to eliminate or phase out overfishing of snowy grouper, golden tilefish, vermilion snapper, and black sea bass; and increase red porgy harvest consistent with an updated stock assessment and rebuilding plan to achieve optimum yield.
Fisheries Off West Coast States; Notice of Availability of Amendment 18 to the Pacific Coast Groundfish Management Plan
Document Number: E6-9027
Type: Proposed Rule
Date: 2006-06-09
Agency: Department of Commerce, National Oceanic and Atmospheric Administration
NMFS announces that the Pacific Fishery Management Council (Council) has submitted Amendment 18 to the Pacific Coast Groundfish Fishery Management Plan (FMP) for Secretarial review. Amendment 18 would modify the FMP to implement a bycatch minimization program for the Pacific coast groundfish fisheries. Amendment 18 is intended to respond to court orders in to establish a bycatch minimization program in the FMP.
Food Stamp Program: Employment and Training Program Provisions of the Farm Security and Rural Investment Act of 2002
Document Number: E6-9001
Type: Rule
Date: 2006-06-09
Agency: Department of Agriculture, Food and Nutrition Service
This rule finalizes the proposed provisions of a rule published on March 19, 2004 to amend Food Stamp Program regulations to codify Food Stamp Employment and Training (E&T) Program provisions of section 4121 of the Farm Security and Rural Investment Act of 2002 (the Farm Bill). This final rule establishes a reasonable formula for allocating the 100 percent Federal grant authorized under the Farm Bill to carry out the E&T Program each fiscal year. This final rule also codifies the Farm Bill provision that makes available up to $20 million a year in additional unmatched Federal E&T funds for State agencies that commit to offer an education/training or workfare opportunity to every applicant and recipient who is an able-bodied adult without dependents (ABAWD), limited to 3 months of food stamp eligibility in a 36-month period, who would otherwise be terminated. This final rule eliminates the current Federal cost-sharing cap of $25 per month on the amount State agencies may reimburse E&T participants for work expenses other than dependent care. This final rule codifies Farm Bill provisions that expand State flexibility in E&T Program spending by repealing the requirements that State agencies earmark 80 percent of their annual 100 percent Federal E&T grants to serve ABAWDs; they meet or exceed their fiscal year 1996 State administrative spending levels to access funds made available by the Balanced Budget Act of 1997; and the Secretary be given the authority to establish maximum reimbursement costs of E&T Program components. Lastly, this final rule rescinds the balance of unobligated funds carried over from fiscal year 2001.
Revisions to the Nevada State Implementation Plan
Document Number: E6-9000
Type: Proposed Rule
Date: 2006-06-09
Agency: Environmental Protection Agency
EPA is proposing to approve revisions to the Nevada State Implementation Plan (SIP). These revisions concern the Air Pollution sections of the Nevada Revised Statutes (NRS). We are proposing to approve the submitted statutes in order to bring the Nevada SIP up to date. These statutes are being approved under the Clean Air Act as amended in 1990 (CAA or the Act). We are taking comments on this proposal and plan to follow with a final action.
National Vaccine Injury Compensation Program: Calculation of Average Cost of a Health Insurance Policy
Document Number: E6-8992
Type: Proposed Rule
Date: 2006-06-09
Agency: Department of Health and Human Services, Health Resources and Services Administration
Subtitle 2 of Title XXI of the Public Health Service Act, as enacted by the National Childhood Vaccine Injury Act of 1986, as amended (the Act), governs the National Vaccine Injury Compensation Program (VICP). The VICP, administered by the Secretary of Health and Human Services (the Secretary), provides that a proceeding for compensation for a vaccine-related injury or death shall be initiated by service upon the Secretary, and the filing of a petition with the United States Court of Federal Claims (the Court). In some cases, the injured individual may receive compensation for future lost earnings, less appropriate taxes and the ``average cost of a health insurance policy, as determined by the Secretary.'' The Secretary now proposes a new method of calculating the average cost of a health insurance policy.
Veterans' Preference
Document Number: E6-8962
Type: Rule
Date: 2006-06-09
Agency: Office of Personnel Management, Personnel Management Office, Agencies and Commissions
The Office of Personnel Management (OPM) is issuing interim regulations to implement statutory changes to veterans' preference contained in the National Defense Authorization Act for FY 2006. These changes expand the definition of a veteran and clarify veterans' preference eligibility for individuals discharged or released from active duty. The intended effect of these changes is to provide conformity between veterans' preference laws and OPM regulations, to further ensure that job seeking veterans receive the preference to which they are entitled.
Food-Contact Surface Sanitizing Solutions; Proposed Revocation of Tolerance Exemptions for Sanitizers with No Food-Contact Uses in Registered Pesticide Products and with Insufficient Data for Reassessment
Document Number: E6-8928
Type: Proposed Rule
Date: 2006-06-09
Agency: Environmental Protection Agency
This document proposes under section 408(e)(1) of the Federal Food, Drug and Cosmetic Act (FFDCA) to revoke the existing exemption from the requirement of a tolerance for the food-contact surface sanitizing solution use of certain antimicrobial pesticides because the Agency has determined that the tolerance exemption corresponds to the food-contact sanitizing use for which there are no longer registered pesticide products, and because there are insufficient data to make the determination of safety required by FFDCA section 408(b)(2). The regulatory actions proposed in this document will contribute toward the Agency's tolerance reassessment requirements under the FFDCA section 408(q), as amended by the Food Quality Protection Act (FQPA) of 1996. By law, EPA is required by August 2006 to reassess the tolerances that were in existence on August 2, 1996.
Airworthiness Directives; Pratt & Whitney PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, PW4090-3, and PW4098 Turbofan Engines
Document Number: 06-5242
Type: Proposed Rule
Date: 2006-06-09
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for Pratt & Whitney PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, PW4090-3, and PW4098 turbofan engines, with certain front turbine hub part numbers installed. This proposed AD would require a onetime visual inspection of the anti-rotation slots in the front turbine hub, for a machining nonconformance, and its replacement if the inspection failed. This proposed AD results from a report of a crack found in an anti- rotation slot of a front turbine hub, during overhaul shop inspection. The anti-rotation slot geometry was not machined in conformance with the design drawing. We are proposing this AD to prevent uncontained engine failure, damage to the airplane, and injury to passengers.
Amendments to Plan of Organization and Operation Effective During Emergency Conditions
Document Number: 06-5232
Type: Rule
Date: 2006-06-09
Agency: Securities and Exchange Commission, Agencies and Commissions
The Securities and Exchange Commission (``Commission'' or ``SEC'') is adopting amendments to certain of its rules that operate in the event of emergency conditions to revise the provisions on delivering submittals, the line of succession to the Chairman in the event of the Chairman's incapacity or unavailability, and make conforming changes. These changes are intended to update these provisions.
Revision of December 2000 Clean Air Act Section 112(n) Finding Regarding Electric Utility Steam Generating Units; and Standards of Performance for New and Existing Electric Utility Steam Generating Units: Reconsideration
Document Number: 06-5173
Type: Rule
Date: 2006-06-09
Agency: Environmental Protection Agency
This action sets forth EPA's decision after reconsidering certain aspects of the March 29, 2005 final rule entitled ``Revision of December 2000 Regulatory Finding on the Emissions of Hazardous Air Pollutants From Electric Utility Steam Generating Units and the Removal of Coal- and Oil-Fired Electric Utility Steam Generating Units from the Section 112(c) List'' (Section 112(n) Revision Rule). We are also issuing our final decision regarding reconsideration of certain issues in the May 18, 2005 final rule entitled ``Standards of Performance for New and Existing Stationary Sources: Electric Utility Steam Generating Units'' (Clean Air Mercury Rule; CAMR). After considering the petitions for reconsideration and the comments received, we are not revising the final Section 112(n) Revision Rule other than explaining in more detail what we meant by the effectiveness element in the term ``necessary.'' The only two substantive changes we are making to CAMR in response to comments involve revisions to the State mercury (Hg) allocations, and to the new source performance standards (NSPS). We also are finalizing the regulatory text that clarifies the applicability of CAMR to municipal waste combusters (MWC) and certain industrial boilers. Finally, we are denying the requests for reconsideration with respect to all other issues raised in the petitions for reconsideration submitted for both rules.
Statewide Transportation Planning; Metropolitan Transportation Planning
Document Number: 06-5145
Type: Proposed Rule
Date: 2006-06-09
Agency: Federal Highway Administration, Department of Transportation, Federal Transit Administration
The FHWA and the FTA are jointly issuing this document which proposes the revision of regulations governing the development of metropolitan transportation plans and programs for urbanized areas, State transportation plans and programs and the regulations for Congestion Management Systems and invites public comment. This proposed revision results from the recent passage of the Safe, Accountable, Flexible, Efficient Transportation Equity Act: a Legacy for Users (SAFETEA-LU) (Pub. L. 109-59, August 10, 2005), which also incorporates changes initiated in its predecessor legislation, the Transportation Equity Act for the 21st Century (TEA-21) (Pub. L. 105-178, June 9, 1998) and generally would make the regulations consistent with current statutory requirements. Interested parties are invited to send comments regarding all facets of this proposal.
Correction to General Order Concerning Mayrow General Trading and Related Entities
Document Number: E6-8961
Type: Rule
Date: 2006-06-08
Agency: Department of Commerce, Bureau of Industry and Security, Industry and Security Bureau
The Bureau of Industry and Security is correcting a final rule that appeared in the Federal Register on June 5, 2006 (71 FR 32272). This rule corrects an inadvertent error in the telephone number listed in the For Further Information Contact: section of the preamble.
Closing of the Port of Noyes, Minnesota, and Extension of the Limits of the Port of Pembina, North Dakota
Document Number: E6-8960
Type: Rule
Date: 2006-06-08
Agency: Department of Homeland Security, Bureau of Customs and Border Protection, Customs and Border Protection Bureau
This rule amends the Department of Homeland Security regulations pertaining to the field organization of the Bureau of Customs and Border Protection by closing the port of entry of Noyes, Minnesota, and extending the limits of the port of entry of Pembina, North Dakota, to include the rail facilities located at Noyes. The closure and extension are the result of the closure by the Canadian Customs and Revenue Agency of the Port of Emerson, Manitoba, Canada, which is located north of the Port of Noyes, and the close proximity of the Port of Noyes to the Port of Pembina.
Au Pair Exchange Programs
Document Number: E6-8958
Type: Rule
Date: 2006-06-08
Agency: Department of State
The Department of State (Department) adopts as final certain proposed amendments to existing au pair regulations. These changes will permit au pair sponsors to request a one-time extension of six, nine, or 12 months beyond an au pair participant's original 12-month period of program participation).
Oral Dosage Form New Animal Drugs; Oxibendazole Suspension
Document Number: E6-8953
Type: Rule
Date: 2006-06-08
Agency: Food and Drug Administration, Department of Health and Human Services
The Food and Drug Administration (FDA) is amending the animal drug regulations to reflect approval of a supplemental new animal drug application (NADA) filed by Pfizer, Inc. The supplemental NADA provides for revised food safety labeling for oxibendazole suspension administered orally to horses as an antiparasitic.
Importation of Fruits and Vegetables; Untreated Citrus From Mexico
Document Number: E6-8935
Type: Rule
Date: 2006-06-08
Agency: Department of Agriculture, Animal and Plant Health Inspection Service
We are amending the fruits and vegetables regulations to provide for the importation of untreated citrus (grapefruit, sweet oranges, and tangerines) from Mexico for processing under certain conditions. We believe the conditions under which untreated citrus from Mexico will be allowed importation to be sufficient for safeguarding fruit that are moving from Mexico to Texas. This action will relieve unnecessary restrictions while continuing to protect against the introduction of quarantine pests through imported fruits.
Utah Regulatory Program
Document Number: E6-8927
Type: Rule
Date: 2006-06-08
Agency: Department of the Interior, Office of Surface Mining Reclamation and Enforcement, Surface Mining Reclamation and Enforcement Office
We are approving a revised amendment to the Utah regulatory program (the ``Utah program'') under the Surface Mining Control and Reclamation Act of 1977 (SMCRA or the Act). Utah proposed changes to the Utah Administrative Rules concerning permit change, renewal, transfer, sale and assignment, cross sections and maps, processing and approval of extensions to the approved permit area, determining civil penalty amounts, and assessing daily civil penalties. Utah revised its program to clarify and strengthen certain parts of the rules.
Missouri Regulatory Program
Document Number: E6-8926
Type: Rule
Date: 2006-06-08
Agency: Department of the Interior, Office of Surface Mining Reclamation and Enforcement, Surface Mining Reclamation and Enforcement Office
We, the Office of Surface Mining Reclamation and Enforcement (OSM), are approving an amendment to the Missouri regulatory program (Missouri program) under the Surface Mining Control and Reclamation Act of 1977 (SMCRA or the Act). Previously we substituted direct Federal enforcement for portions of the Missouri program. Missouri regained full authority for its program on February 1, 2006. Missouri proposed to amend its approved regulatory program and submitted a temporary emergency regulatory program rule (emergency rule) to revise Missouri's regulations regarding bonding of surface coal mining and reclamation operations. The emergency rule will allow Missouri to transition from a ``bond pool'' approach to bonding to a ``full cost bond'' approach in a timely manner. Missouri proposed to revise its program to improve operational efficiency.
State Abandoned Mine Land Reclamation Plan
Document Number: E6-8925
Type: Proposed Rule
Date: 2006-06-08
Agency: Department of the Interior, Office of Surface Mining Reclamation and Enforcement, Surface Mining Reclamation and Enforcement Office
We, the Office of Surface Mining Reclamation and Enforcement (OSM), are announcing receipt of a partially proposed abandoned mine land reclamation (AMLR) plan under the Surface Mining Control and Reclamation Act of 1977 (SMCRA or the Act). Mississippi proposes revisions to and addition of statutes to the Mississippi Surface Coal Mining and Reclamation Law in order to authorize and establish an AMLR plan. If we approve Mississippi's proposed statutes, our approval will not give Mississippi authority to receive and expend Federal AMLR grant funds. Mississippi would need to submit to us additional information required under 30 CFR 884.13 in order for us to make the findings necessary for full approval of an AMLR plan. The State will be able to receive and spend Federal funds only after we approve its complete State AMLR plan. This document gives the times and locations that the Mississippi AMLR plan statutes are available for your inspection, the comment period during which you may submit written comments, and the procedures that will be followed for the public hearing, if one is requested.
Revision of Fee Schedules; Fee Recovery for FY 2006; Correction
Document Number: E6-8923
Type: Rule
Date: 2006-06-08
Agency: Nuclear Regulatory Commission, Agencies and Commissions
This document corrects a final rule appearing in the Federal Register on May 30, 2006 (71 FR 30722) concerning the licensing, inspection, and annual fees charged to NRC applicants and licensees in compliance with the Omnibus Budget Reconciliation Act of 1990, as amended. This action is necessary to correct typographical and printing errors.
Airworthiness Directives; Boeing Model 707-100 Long Body, -100B Long Body, -100B Short Body, -E3F, -300, -300B, and -300C Series Airplanes; Model 727-100 and -200 Series Airplanes; Model 737-200, -200C, -300, -400, and -500 Series Airplanes; Model 747-100B, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747SR, and 747SP Series Airplanes; Model 757-200 and 757-200PF Series Airplanes; and Model 767-200 and -300 Series Airplanes; Equipped With Observer or Attendant Seats
Document Number: E6-8901
Type: Proposed Rule
Date: 2006-06-08
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Boeing airplanes. The existing AD currently requires inspection of the attachment of the shoulder restraint harness to the mounting bracket on certain observer and attendant seats to determine if a C-clip is used in the attachment, and corrective action, if necessary. This proposed AD would remove certain airplanes from the applicability and add others. This proposed AD results from the determination that some airplanes had been inadvertently included in or excluded from the applicability of the existing AD and that certain additional new airplanes are now subject to the identified unsafe condition. We are proposing this AD to prevent detachment of the shoulder restraint harness of the attendant or observer seat from its mounting bracket during service, which could result in injury to the occupant of the seat.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.