Federal Aviation Administration May 2024 – Federal Register Recent Federal Regulation Documents

This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPS) and associated Takeoff Minimums and Obstacle Departure procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Bell Textron Canada Limited Model 505 helicopters. This proposed AD was prompted by a fuel leakage discovered during fuel system crash impact testing activity. This proposed AD would require installing a grommet around the sump drain port fitting airframe hole, as specified in a Transport Canada AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA is correcting an airworthiness directive (AD) that published in the Federal Register. That AD applies to certain General Electric Company (GE) Model GE90-110B1 and GE90-115B engines. As published, references to the service information include a typographical error in the regulatory text of the AD. This document corrects that error in all references. In all other respects, the original document remains the same.

This action amends Class E airspace extending upward from 700 feet above the surface for Barrow County Airport, Winder, GA. This action increases the existing radius and updates the airport's name and geographic coordinates to coincide with the FAA's database.

The FAA proposes to supersede Airworthiness Directive (AD) 2023-22-13, which applies to certain Dassault Aviation Model FALCON 7X airplanes. AD 2023-22-13 requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2023-22- 13, the FAA has determined that new or more restrictive airworthiness limitations are necessary. This proposed AD would continue to require certain actions in AD 2023-22-13 and would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.

This action extends the Order Limiting Operations at New York LaGuardia Airport (LGA) published on December 27, 2006, as most recently extended October 28, 2022. The Order remains effective until October 24, 2026.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on March 14, 2024. The collection involves maintaining and recording "the status of life-limited parts of each airframe, engine, propeller, rotor, and appliance. The information to be collected is necessary for verifying the time-life of life-limited parts and is used to ensure parts that have reached their life-limit are not installed on an aircraft, or are removed from an aircraft and properly dispositioned.

This Notice provides information to Federal, State, and local agencies; Native American tribes; and other interested persons regarding the FAA's intent to prepare an EIS to evaluate the potential environmental impacts of issuing a commercial launch Vehicle Operator License to SpaceX for the Starship-Super Heavy launch vehicle at Launch Complex 39A (LC-39A) at Kennedy Space Center (KSC), Florida. SpaceX proposes to construct launch, landing, and other associated infrastructure at and in proximity to LC-39A. The proposal would also include Starship-Super Heavy launches at LC-39A; recoverable Super Heavy booster and Starship landings at LC-39A or on a droneship; and expendable Super Heavy booster and Starship landings in the ocean. The FAA will prepare the EIS in accordance with the National Environmental Policy Act of 1969, the Council on Environmental Quality Regulations for Implementing the Procedural Provisions of NEPA, and FAA Order 1050.1F, Environmental Impacts: Policies and Procedures, as part of its licensing process. Additional information is available online at: https://www.faa.gov/space/stakeholder_engagement/spacex_stars hip_ksc.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Bell Textron Inc., Model 212, 412, 412CF, and 412EP helicopters. This proposed AD was prompted by reports of cracked tail boom attachment barrel nuts (barrel nuts). This proposed AD would require replacing all steel alloy barrel nuts with nickel alloy barrel nuts and, replacing or inspecting other tail boom attachment point hardware and depending on the results, replacing hardware, stabilizing torque, and applying torque stripes. This proposed AD would also require repetitively inspecting torque and, depending on the results, corrective action. This proposed AD would require repetitively replacing the upper left-hand (LH) tail boom attachment bolt (bolt) and repetitively inspecting the other tail boom attachment point bolts. Lastly, this proposed AD would prohibit installing steel alloy barrel nuts. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA is correcting a final rule published on April 24, 2024. In that document the FAA adopts standards for measuring non- volatile particulate matter (nvPM) exhaust emissions from aircraft engines. With this rulemaking, the FAA implements the nvPM emissions standards adopted by the Environmental Protection Agency (EPA), allowing manufacturers to certificate engines to the new nvPM emissions standards in the United States and fulfilling the statutory obligations of the FAA under the Clean Air Act. This document corrects errors in the preamble and regulatory text of that document.

This action proposes special conditions for the Airbus Model A321neoXLR airplane. This airplane will have a novel or unusual design feature when compared to the technology envisaged by the airworthiness standards for transport category airplanes. This design feature is an integral rear center tank (RCT). The applicable airworthiness regulations do not contain adequate or appropriate safety standards for fire-safety performance of fuel-tank skin or structure in a post-crash external fuel-fed ground fire. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

The FAA is adopting a new airworthiness directive (AD) for all Rolls-Royce Deutschland Ltd & Co KG (RRD) Model Trent 1000-A, Trent 1000-A2, Trent 1000-AE, Trent 1000-AE2, Trent 1000-C, Trent 1000-C2, Trent 1000-CE, Trent 1000-CE2, Trent 1000-D, Trent 1000-D2, Trent 1000- E, Trent 1000-E2, Trent 1000-G, Trent 1000-G2, Trent 1000-H, Trent 1000-H2, Trent 1000-J2, Trent 1000-K2, and Trent 1000-L2 engines. This AD was prompted by reports of wear in the combining spill valve (CSV) assembly of certain hydro-mechanical units (HMUs). This AD requires removing certain HMUs from service and replacing with a serviceable part. This AD also prohibits the installation of certain HMUs unless the HMU is a serviceable part or the CSV assembly has been replaced, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference The FAA is issuing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD- 500-1A11 airplanes. This proposed AD was prompted by a report that at various lavatory and galley locations within the airplane, incorrect terminal lugs were installed which are not compatible with the associated wire gauge. This proposed AD would require removing and replacing existing lug terminals at various lavatory and galley locations, as specified in a Transport Canada AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for certain ATRGIE Avions de Transport R[eacute]gional Model ATR42 and ATR72 airplanes. This AD was prompted by a report of an electrical contactor that failed with contacts in the intermediate position, causing the airplane to lose power to multiple electrical systems. This AD requires repetitive operational tests of the affected part, and, depending on findings, accomplishment of applicable corrective action, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is superseding Airworthiness Directive (AD) 2021-20- 08, which applied to certain Airbus SAS Model A318, A319, A320, A321, A330-200, A330-200 Freighter, A330-300, A330-800, A330-900, A340-200, A340-300, A340-500, A340-600, and A380-800 series airplanes. AD 2021- 20-08 required replacing certain nickel-cadmium (Ni-Cd) batteries with serviceable Ni-Cd batteries. This AD was prompted by a report that repetitive disconnection and reconnection of certain Ni-Cd batteries during airplane parking or storage could lead to a reduction in capacity of those batteries. This AD adds airplanes to the applicability and requires replacement of certain affected parts with serviceable parts as a precondition for return to service of airplanes from storage or parking, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500- 1A11 airplanes. This AD was prompted by a design review that identified the fixed emergency locator transmitter (ELT) lithium batteries would not be sufficiently cooled by the outside air in the event of a thermal runaway event. This AD requires replacing the ELT with a new ELT with redesigned batteries, as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval for a new information collection. The collection involves obtaining information from FAA employees and contractors who will travel overseas on official business. The information to be collected will be used in the event an FAA employee and/or contractor is isolated overseas and requires lifesaving assistance.

The FAA is adopting a new airworthiness directive (AD) for certain MHI RJ Aviation ULC Model CL-600-2C10 (Regional Jet Series 700, 701 & 702); CL-600-2C11 (Regional Jet Series 550); CL-600-2D15 (Regional Jet Series 705); and CL-600-2D24 (Regional Jet Series 900) airplanes. This AD was prompted by a determination that a potential crack of the tombstone fitting lug cannot be detected as the bushings remain in place during accomplishment of the special detailed inspection (SDI) required by a certain airworthiness limitation (ALI) task. This AD requires inspecting the tombstone fitting lug with a new SDI sub-surface ultrasound procedure when accomplishing the ALI task, as specified in a Transport Canada AD, which is incorporated by reference. This AD also requires corrective actions if necessary. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 757-200, 757-200CB, and 757-300 airplanes. This AD was prompted by cracks on both sides of the airplane in the station (STA) 1640 frame web between S-14 and S-15. This AD requires an inspection or maintenance records check for existing liner holes in the STA 1640 frame web between S-14 and S-15, and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.

This action proposes to revoke the Class E airspace at Gibson City, IL. The FAA is proposing this action as the result of the instrument procedures being cancelled and the airspace no longer being required.

This action proposes to amend the Class E airspace at Llano, TX, and Mason, TX. The FAA is proposing this action as the result of an airspace review conducted due to the decommissioning of the Llano very high frequency omnidirectional range (VOR) as part of the VOR Minimum Operational Network (MON) Program. The geographic coordinates of the Llano Municipal Airport, Llano, TX, would also be updated to coincide with the FAA's aeronautical database. This action will bring the airspace into compliance with FAA orders and support instrument flight rule (IFR) procedures and operations.

This action proposes to amend the Class E airspace at Beloit, KS. The FAA is proposing this action as the result of an airspace review conducted due to the decommissioning of the Mankato very high frequency omnidirectional range (VOR) as part of the VOR Minimum Operational Network (MON) Program. The geographic coordinates of the airport would also be updated to coincide with the FAA's aeronautical database. This action will bring the airspace into compliance with FAA orders and support instrument flight rule (IFR) procedures and operations.

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). This proposed AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.