Federal Aviation Administration 2022 – Federal Register Recent Federal Regulation Documents

The Federal Aviation Administration (FAA) is considering a proposal and invites public comment to change a portion of the airport from aeronautical use to non-aeronautical use at Paso Robles Municipal Airport (PRB), San Luis Obispo County, California. The proposal consists of one parcel containing 22.07 acres of airport land located southwest corner of the airport facility North of Airport Road and West of Satellite Drive.

This action proposes to amend VHF Omnidirectional Range (VOR) Federal airways V-6, V-10, V-30, V-100, and V-233 in the vicinity of Litchfield, MI. The airway modifications are necessary due to the planned decommissioning of the VOR portion of the Litchfield, MI, VOR/Distance Measuring Equipment (VOR/DME) navigational aid (NAVAID). The Litchfield VOR/DME NAVAID provides navigational guidance for portions of the affected VOR Federal airways listed above and is planned to be decommissioned as part of the FAA's VOR Minimum Operational Network (MON) program.

For noncompliance with the remote identification production requirements applicable to unmanned aircraft, which occurs on or before December 16, 2022, the FAA will consider all circumstances, in particular, the delay in the FAA's acceptance of a means of compliance, when exercising its discretion whether to take enforcement action.

This action amends the Class D and Class E airspace and revokes Class E airspace at La Crosse, WI. This action due to an airspace review conducted as part of the decommissioning of the La Crosse very high frequency (VHF) omnidirectional range (VOR) as part of the VOR Minimal Operational Network (MON) Program.

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A321-251N, A321-251NX, A321-252N, A321-252NX, A321-253N, and A321-253NX airplanes. This proposed AD was prompted by a stress analysis on the engine structure that indicated that the fail- safe lug may not be able to sustain, during one inspection interval as currently specified in an airworthiness limitations item, the loads deriving from the engagement of the secondary load path within that inspection interval for the aft engine mount system. This proposed AD would require repetitive detailed inspections of the aft engine mount and secondary load path clearance fail-safe pin and replacement of the engine if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain De Havilland Aircraft of Canada Limited Model DHC-8-400 series airplanes. This proposed AD was prompted by a report that electrical bonding jumpers had been installed on fuel scavenge lines even after the removal was required by previous AD rulemaking and that electrical bonding jumpers may have been installed in production or in service at other locations. This proposed AD would require an inspection for electrical bonding jumpers and brackets on the fuel scavenge and vent lines at specific wing locations, and if installed, removal or modification of those jumpers and brackets. This proposed AD would also require a records check to determine if certain maintenance tasks were performed and removal, modification, or rework if those tasks were performed. This proposed AD would also prohibit the use of earlier versions of certain maintenance tasks. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain General Electric Company (GE) GEnx-1B and GEnx-2B model turbofan engines. This proposed AD was prompted by a manufacturer investigation that revealed that certain high-pressure turbine (HPT) stage 2 disks, forward seals, and stages 6-10 compressor rotor spools were manufactured from powder metal material suspected to contain iron inclusion. This proposed AD would require the replacement of the affected HPT stage 2 disks, forward seals, and stages 6-10 compressor rotor spools. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA is publishing this notice to solicit nominations for membership on the ODA for Transport Airplanes Expert Review Panel (``Review Panel'').

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A350-941 airplanes. This AD was prompted by a report indicating that the inflatable free aisle restrictor (IFAR) on certain single lane slide-rafts demonstrated inconsistent release behavior in aft wind conditions. This AD requires replacing an affected part with a serviceable part, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also prohibits the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for all The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747- 200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. This proposed AD was prompted by reports that high temperature composite trim air diffuser ducts (TADD) showed composite degradation and signs of hot air leakage. This proposed AD would require a one-time low frequency eddy current (LFEC) inspection of certain center tank upper skin panels on the right and left side for any structural damage due to heat exposure, and repair if necessary. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Gulfstream Aerospace Corporation Model GVII-G500 and GVII- G600 airplanes. This proposed AD was prompted by reports of two landing incidents in which the alpha limiter engaged in the landing flare in unstable air, resulting in high rate of descent landings and damage to the airplanes. This proposed AD would require updating the flight control computer (FCC) software. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 747-8 and -8F series airplanes. This proposed AD was prompted by reports of cracking in stringers and splice fittings located at stringer splices at multiple body stations. This proposed AD would require an inspection of each free flange of the stringers at the stringer splice for the presence of radius fillers at fastener locations, an inspection for cracking of the stringers and stringer splice fittings at certain stringer splice locations, and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.

This action amends Area Navigation (RNAV) route Q-81 to realign a portion of the route to improve traffic flows, and to remove Canadian RNAV route Q-947 at the request of NavCanada. These changes support the Northeast Corridor Atlantic Coast Route Project.

This action amends 4 VHF Omnidirectional Range (VOR) Federal Airways, (V-7, V-9, V-106, and V-214); and removes 5 VOR Federal Airways, (V-58, V-130, V-149, V-445, V-451) in support of the FAA's VOR Minimum Operation Network (MON) project.

This action corrects a final rule published by the FAA in the Federal Register on August 29, 2022, that amends United States Area Navigation (RNAV) route T-232 in the vicinity of Fairbanks, AK, in support of a large and comprehensive T-route modernization project for the state of Alaska. The final rule identified the IMARE, AK, route point as a waypoint (WP), in error. This action makes an editorial correction to the references of the IMARE, AK, WP to change it to be reflected as a Fix and match the FAA's aeronautical database information.

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A318, A319, A320, and A321 series airplanes. This AD was prompted by unclear and incomplete placard instructions for the doghouse door lock. This AD requires installing improved handling instruction placards on affected doghouses and re-identifying the doghouses, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also prohibits the installation of affected doghouses under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.

The Federal Aviation Administration (FAA) announces its determination that the noise exposure maps submitted by the San Diego County Regional Airport Authority for San Diego International Airport complies with applicable statutory and regulatory requirements, refer to the supplementary information for details. Further, in conjunction with the noise exposure maps, FAA is reviewing the proposed noise compatibility program for the San Diego International Airport, which the FAA will approve or disapprove on or before February 28, 2023. This notice also announces the availability of this noise compatibility program for public review and comment.

The FAA proposes to supersede airworthiness directive (AD) 77- 04-06, which applies to Messerschmitt-Bolkow-Blohm (MBB) (now Airbus Helicopters Deutschland GmbH (AHD)) Model BO-105A and BO-105 C helicopters; AD 2002-13-06, which applies to certain Eurocopter Deutschland GmbH (ECD) (now Airbus Helicopters Deutschland GmbH (AHD)) Model BO-105A, BO-105C, BO-105 C-2, BO-105 CB-2, BO-105 CB-4, BO-105 CS-2, BO-105 CBS-2, BO-105S, and BO-105LS A-1 helicopters; AD 2016-25- 14, which applies to certain Airbus Helicopters Deutschland GmbH (AHD) Model BO-105LS A-3 helicopters; and AD 2021-10-14, which applies to certain Airbus Helicopters Deutschland GmbH (AHD) Model BO-105A, BO- 105C, BO-105S, and BO-105LS A-3 helicopters. AD 77-04-06 requires reducing the life limit on certain main rotor gearbox (MGB) supports. AD 2002-13-06 requires determining the calendar age, number of flights, and flight hours time-in-service (TIS) on certain tension-torsion (TT) straps; revising the Airworthiness Limitations Schedule (ALS) of the existing maintenance manual; removing and replacing each TT strap that has exceeded its life limit, or if the TT strap's total hours TIS or number of flights and age are not known; and modifying certain parts. AD 2016-25-14 requires establishing a life limit for certain TT straps and removing certain parts that have exceeded the new life limit. AD 2021-10-14 requires replacement of certain TT straps with serviceable parts, and implementation of a new storage life limit for certain TT straps. Since the FAA issued those ADs, new and more restrictive airworthiness limitations have been issued. This proposed AD would require incorporating into existing maintenance records requirements (airworthiness limitations) as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). This proposed AD would also prohibit the installation of certain part-numbered TT straps. The FAA is proposing this AD to address the unsafe condition on these products.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval renew information collection. Advisory Circular 70-2A provides guidance to civilian air crews on the reporting of laser illumination incidents and recommended mitigation actions to be taken in order to ensure continued safe and orderly flight operations.

The FAA is adopting a new airworthiness directive (AD) for certain MHI RJ Aviation ULC Model CL-600-2D24 (Regional Jet Series 900) airplanes. This AD was prompted by a report of a manufacturing error that can create dents on the lower wing plank, close to the flap arm locations at certain wing stations; as a result, cracks could develop and weaken the structural integrity of the wings before being detected by any existing required inspections. This AD requires an inspection for damage (including dents, cracks, discoloration, gouges, scratches, or other surface damage) of the lower wing plank in the flap arm areas at certain wing stations, and repair if necessary. The FAA is issuing this AD to address the unsafe condition on these products.

These special conditions are issued for the Bombardier Model BD-700-1A10 and BD-700-1A11 airplanes. These airplanes, as modified by L2 Consulting Services, Inc., will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for airplanes. This design feature is associated with the installation of an electronic network system architecture that will allow increased connectivity to and access from external network sources, (e.g., operator networks, wireless devices, internet connectivity, service provider satellite communications, electronic flight bags, etc.) to the airplane's previously isolated electronic assets (networks, systems, and databases). The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

The FAA is superseding Airworthiness Directive (AD) 2017-10- 24, which applied to certain Airbus SAS Model A330-200 series airplanes, Model A330-200 Freighter series airplanes, and Model A330- 300 series airplanes; AD 2018-23-14, which applied to certain Airbus SAS Model A330-200 series airplanes, Model A330-200 Freighter series airplanes, and Model A330-300 series airplanes; and AD 2021-05-12, which applied to certain Airbus SAS Model A330-200 Freighter series airplanes. AD 2017-10-24, AD 2018-23-14, and AD 2021-05-12 require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD revises the applicability by adding airplanes. This AD continues to require the actions in AD 2018-23-14 and AD 2021-05-12, and requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for all General Electric Company (GE) CT7-8A model turboshaft engines. This AD was prompted by the manufacturer revising the airworthiness limitations section (ALS) of the existing engine maintenance manual (EMM) to incorporate reduced life limits for certain stage 1 turbine aft cooling plates, stage 2 turbine forward cooling plates, turbine interstage seals, and stage 4 turbine disks. This AD requires revising the ALS of the existing EMM and the operator's existing approved maintenance or inspection program, as applicable, to incorporate reduced life limits for these parts. The FAA is issuing this AD to address the unsafe condition on these products.

This action amends Class D airspace, Class E Surface airspace, and Class E Airspace Designated as an Extension to Class D airspace at Martin State Airport, Baltimore, MD. This action replaces the Baltimore Very High Frequency Omnidirectional Range Collocated Tactical Air Navigation (VORTAC) with the term Point of Origin. Also, this action removes unnecessary verbiage from the descriptor header. In addition, this action makes an editorial change replacing the term Airport/ Facility Directory with the term Chart Supplement in the legal descriptions of associated Class D and E airspace and makes the editorial change replacing the term Notice to Airmen with the term Notice to Air Missions. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations in the area.

The FAA is superseding Airworthiness Directive (AD) 2022-05- 13, which applied to certain Honda Aircraft Company LLC (Honda) Model HA-420 airplanes. AD 2022-05-13 required incorporating temporary revisions into the airplane flight manual (AFM) and the quick reference handbook (QRH) that modify procedures for windshield heat operation until the affected windshield assemblies are replaced. This AD was prompted by typographical errors found in certain document numbers specified in the preamble and in certain paragraphs of the regulatory information in AD 2022-05-13. This AD retains all actions required by AD 2022-05-13 and corrects the incorrect document numbers. The FAA is issuing this AD to address the unsafe condition on these products.