Federal Aviation Administration 2010 – Federal Register Recent Federal Regulation Documents

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model AS332L2 helicopters. This AD results from a mandatory continuing airworthiness information (MCAI) AD issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community. The MCAI AD states that the AD was issued after the discovery of broken swashplate bearing attaching screw heads. Failure of these screw heads could lead to the loss of the coupling between the non-rotating and the rotating swashplate. This AD is intended to prevent loss of power to the rotating swashplate and subsequent loss of control of the helicopter.

The FAA is superseding an existing airworthiness directive (AD), which applies to Model BAe 146 airplanes and Model Avro 146-RJ airplanes. That AD currently requires revising the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness to incorporate life limits for certain items and inspections to detect fatigue cracking in certain structures. This new AD requires incorporating new and more restrictive life limits for certain items and for certain inspections to detect fatigue cracking in certain structures. This AD also requires revising the airworthiness limitations to include critical design configuration control limitations for the fuel system. This AD results from issuance of a later revision to the airworthiness limitations. We are issuing this AD to ensure that fatigue cracking of certain structural elements is detected and corrected, and to prevent ignition sources in the fuel tanks; fatigue cracking of certain structural elements could adversely affect the structural integrity of these airplanes.

The FAA is issuing this notice to advise the public of a meeting of EUROCAE WG-72: RTCA Special Committee 216: Aeronautical Systems Security (Joint Meeting).

The FAA proposes to adopt a new airworthiness directive (AD) for Pratt & Whitney (PW) JT8D-9, -9A, -11, -15, -17, and -17R turbofan engines. This proposed AD would require overhauling fan blade leading edges at the first shop visit after 4,000 cycles-in-service (CIS) since the last total fan blade overhaul was performed. This proposed AD results from reports of failed fan blades. We are proposing this AD to prevent high-cycle fatigue cracking at the blade root, which could result in uncontained failures of first stage fan blades and damage to the airplane.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: A number of LPT casings have been found cracked during engine shop visit. Cracking of the LPT casing reduces the capability of the casing to contain debris in the event of an LPT stage 1 blade failure. Therefore, blade failure in an engine featuring a cracked LPT casing may result in release of uncontained high energy debris. For the reason described above, this AD requires repetitive inspections and corrective actions, depending on findings. We are proposing this AD to detect cracks in the LPT casings, which could result in the release of uncontained high-energy debris in the event of a stage 1 blade failure. Uncontained high-energy debris could result in damage to the airplane.

We propose to adopt a new airworthiness directive (AD) for certain Model 737-100 and -200 series airplanes. This proposed AD would require repetitive inspections for cracking and damaged fasteners of certain fuselage frames and stub beams, and corrective actions if necessary. For certain airplanes, this proposed AD would also require repetitive inspections for cracking of the inboard chord fastener hole of the frame at body station 639, stringer S-16, and corrective actions if necessary. For certain airplanes, this proposed AD would also require an inspection to determine the edge margin of the lower chord. For airplanes with a certain short edge margin, this proposed AD requires repetitive inspections for cracking, and corrective actions if necessary; replacing the lower chord terminates the repetitive inspections. This proposed AD requires an eventual preventive modification. For certain airplanes, doing the modification or a repair would terminate the repetitive inspections for the repaired or modified frame only. For airplanes on which the modification or repair is done at certain body stations, this proposed AD would require repetitive inspections for cracking of certain frame webs and inner and outer chords, and corrective actions if necessary. For certain other airplanes, this proposed AD requires a modification which includes reinforcing the body frame inner chords, replacing the stub beam upper chords and attach angles, and reinforcing the stub beam web. This proposed AD results from reports of fatigue cracks at certain frame sections, in addition to stub beam cracking, caused by high flight cycle stresses from both pressurization and maneuver load. We are proposing this AD to detect and correct fatigue cracking of certain fuselage frames and stub beams, and possible severed frames, which could result in reduced structural integrity of the frames. This reduced structural integrity can increase loading in the fuselage skin, which will accelerate skin crack growth and result in rapid decompression of the fuselage.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: Three events have been reported where insulation material was found to be fouling pulleys in the aileron interconnect circuit in the cabin roof area. Interference between the cable and the insulation bag causes the material to be drawn into the gap between the pulley and the pulley guard. This condition, if not detected and corrected, could lead to restricted aileron movement and consequently, reduced control of the aeroplane.

We propose to adopt a new airworthiness directive (AD) for certain Model 747-400 and 747-400D series airplanes. This proposed AD would require installing aluminum gutter reinforcing brackets to the forward and aft drip shield gutters of the main equipment center (MEC); and adding a reinforcing fiberglass overcoat to the top surface of the MEC drip shield, including an inspection for cracking and holes in the MEC drip shield, and corrective actions if necessary. This proposed AD also provides for an option to install an MEC drip shield drain system, which, if accomplished, would extend the compliance time for adding the reinforcing fiberglass overcoat to the top surface of the MEC drip shield. This proposed AD results from a report indicating that an operator experienced a multi-power system loss in-flight of 1, 2, and 3 alternating current (AC) electrical power systems located in the MEC. We are proposing this AD to prevent water penetration into the MEC, which could result in the loss of flight critical systems.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

This action proposes special conditions for the Boeing 747-468 airplane. This airplane, as modified by Jet Aviation, will have a novel or unusual design feature associated with the installation of a medical lift. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

This action amends Class E airspace for the Marion, IL area, adding additional controlled airspace to accommodate Area Navigation (RNAV) Standard Instrument Approach Procedures (SIAPs) at Southern Illinois Airport, Carbondale/Murphysboro, IL. The FAA is taking this action to enhance the safety and management of Instrument Flight Rule (IFR) operations at the airport.

This action proposes to amend Class E airspace at Perham, MN. Additional controlled airspace is necessary to accommodate new Standard Instrument Approach Procedures (SIAPs) at Perham Municipal Airport, Perham, MN. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations at the airport.

The FAA is issuing this notice to advise the public of a meeting of RTCA Government/Industry Air Traffic Management Advisory Committee (ATMAC).

This action proposes to amend Class E airspace at Pauls Valley, OK. Additional controlled airspace is necessary to accommodate new Standard Instrument Approach Procedures (SIAPs) at Pauls Valley Municipal Airport. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations at the airport.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA publishes a monthly notice, as appropriate, of PFC approvals and disapprovals under the provisions of the Aviation Safety and Capacity Expansion Act of 1990 (Title IX of the Omnibus Budget Reconciliation Act of 1990) (Pub. L. 101-508) and Part 158 of the Federal Aviation Regulations (14 CFR Part 158). This notice is published pursuant to paragraph d of Sec. 158.29.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA is superseding an existing airworthiness directive (AD), which applies to certain Model 747 airplanes. That AD currently requires repetitive inspections to detect cracking in certain fuselage skin lap joints, and repair if necessary. This new AD expands the inspection area in the existing AD, adds a modification of certain lap joints, and adds certain post-repair inspections of the lap joints. Accomplishing the modification ends the repetitive inspections required by the existing AD for the length of lap joint that is modified. This AD results from a structural review of affected skin lap joints for widespread fatigue damage. We are issuing this AD to prevent fatigue cracking in certain lap joints, which could result in rapid depressurization of the airplane.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation Model 390 airplanes. This AD requires you to inspect the essential bus lightning strike protection for proper installation of metal oxide varistor (MOV) and spark gap wiring. This AD also requires you to rework the wiring as necessary to achieve the required lightning strike/surge protection. This AD results from a report that the wires to the MOV and spark gap were swapped. We are issuing this AD to detect and correct improper installation of the MOV and spark gap wiring, which could result in overload of the MOV in a lightning strike and allow electrical energy to continue to the essential bus and disable equipment that receives power from the essential bus. The disabled equipment could include the autopilot, anti-skid system, hydraulic indicator, spoiler system, pilot primary flight display, audio panel, or the 1 air data computer. This failure could lead to a significant increase in pilot workload during adverse operating conditions.

The FAA proposes to rule and invite public comment for a change in airport property from aeronautical use to non-aeronautical use at the Williamsport Regional Airport, Williamsport, Pennsylvania.