Federal Aviation Administration 2008 – Federal Register Recent Federal Regulation Documents

Results 351 - 400 of 1,726
Notice of Intent To Rule on Passenger Facility Charge (PFC) Application 08-08-C-00-SMF, To Impose and Use PFC Revenue at Sacramento International Airport, Sacramento, CA
Document Number: E8-23911
Type: Notice
Date: 2008-10-09
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to rule and invites public comment on the application to impose and use PFC revenue at Sacramento International Airport, under the provisions of the Aviation Safety and Capacity Expansion Act of 1990 (Title IX of the Omnibus Budget Reconciliation Act of 1990) (Public Law 101-508) and Part 158 of the Federal Aviation Regulations (14 CFR part 158).
Airworthiness Directives; Boeing Model 767-200, -300, and -400ER Series Airplanes
Document Number: E8-23667
Type: Rule
Date: 2008-10-09
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 767-200, -300, and -400ER series airplanes. That AD currently requires an inspection to determine if the door-mounted escape slide/rafts have certain part numbers. This new AD does not retain that requirement. This new AD continues to require an inspection for excessive tension of the firing cable, and procedures for providing slack in the firing cable or rerouting the firing cable if necessary. For certain airplanes, this new AD also requires a review of the airplane maintenance records to determine if a certain service bulletin has been incorporated, or an inspection to determine if certain door-mounted escape slide/rafts are installed. This new AD also requires modification of certain escape slide/rafts. This AD results from reports of uncommanded inflation inside the airplane of a door-mounted escape slide/raft located in the passenger compartment. We are issuing this AD to prevent injury to maintenance personnel, passengers, and crew during otherwise normal operating conditions and to prevent interference with evacuation of the airplane during an emergency, due to uncommanded inflation of a door-mounted escape slide/raft.
Airworthiness Directives; Boeing Model 737-300, -400, and -500 Series Airplanes
Document Number: E8-23658
Type: Rule
Date: 2008-10-09
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all Boeing Model 737-300, -400, and -500 series airplanes. This AD requires repetitive inspections for discrepancies of the fuse pins of the inboard and outboard midspar fittings of the nacelle strut, and corrective actions if necessary. This AD results from a report of corrosion damage of the chrome runout on the head side found on all four midspar fuse pins of the nacelle strut. Additionally, a large portion of the chrome plate was missing from the corroded area of the shank. We are issuing this AD to detect and correct discrepancies of the fuse pins of the inboard and outboard midspar fittings of the nacelle strut, which could result in reduced structural integrity of the fuse pins and consequent loss of the strut and separation of the engine from the airplane.
Airworthiness Directives; Hawker Beechcraft Corporation Model 390 Airplanes
Document Number: E8-23643
Type: Rule
Date: 2008-10-09
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation Model 390 airplanes. This AD requires you to modify the cabin barometric pressure switch and cabin altitude high switch installations and perform a functional test of the switches and related systems. This AD results from the possibility of barometric pressure switch electrical connections being incorrectly connected or inadvertently disconnected. We are issuing this AD to modify the cabin barometric pressure switch and cabin altitude high switch to prevent them from becoming incorrectly connected or inadvertently disconnected, which may result in no CABIN ALT HI annunciation in the cockpit and no automatic deployment of the cabin oxygen masks. This failure could lead to incapacitation of the crew due to hypoxia with possible inability to control the airplane.
Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800, and -900 Series Airplanes Equipped With CFM56-7 Engines
Document Number: E8-23573
Type: Rule
Date: 2008-10-09
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 737-600, -700, and -800 series airplanes. That AD currently requires repetitive inspections to detect damage of the aft strut insulation blanket, and eventual replacement of the insulation blankets with new, improved blankets. This new AD adds airplanes to the applicability and requires installation of a new heat insulation blanket and new cover plate on the left and right side engine struts. This new AD does not retain the requirements of the existing AD but does terminate the requirements of the existing AD. This AD results from reports of damaged heat insulation blankets on the engine struts. We are issuing this AD to prevent exposure of the lower surface of the strut to extreme high temperatures, consequent creation of a source of fuel ignition, and increased risk of an uncontrollable fire and possible fuel tank explosion.
Airworthiness Directives; Boeing Model 737-100, -200, -200C, -300, -400, and -500 Series Airplanes
Document Number: E8-23828
Type: Proposed Rule
Date: 2008-10-08
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for all Boeing Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. For all airplanes, this proposed AD would require repetitive overhaul of the retract actuator beam of the main landing gear (MLG). For certain airplanes, this proposed AD would require repetitive inspections for damage of the retract actuator beam, and related investigative and corrective actions if necessary. This proposed AD results from reports of broken retract actuator beams of the MLG and the subsequent failure of the MLG to fully retract. We are proposing this AD to detect and correct broken retract actuator beams of the MLG, which could cause damage to the beam arm, hydraulic tubing, and flight control cables. Damage to the flight control cables could result in loss of control of the airplane.
Airworthiness Directives; Boeing Model 747 Airplanes
Document Number: E8-23824
Type: Proposed Rule
Date: 2008-10-08
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Boeing Model 747 airplanes. The existing AD currently requires repetitive inspections to detect evidence of wear damage in the area at the interface between the vertical stabilizer seal and fuselage skin, and corrective actions, if necessary. The existing AD also provides for an optional terminating action for the repetitive inspections. For all airplanes, this proposed AD would require doing repetitive inspections for wear damage and cracks of the fuselage skin in the interface area of the vertical stabilizer seal and fuselage skin, doing a detailed inspection for wear damage and cracks of the surface of any skin repair doubler in the area, and doing corrective actions. For airplanes on which the fuselage skin has been blended to remove wear damage, this proposed AD would require doing repetitive external detailed inspections or high frequency eddy current inspections for cracks of the blended area of the fuselage skin, and corrective actions if necessary. This proposed AD results from reports of wear damage on airplanes with fewer than 8,000 total flight cycles. In addition, there have been three reports of skin wear damage on airplanes that applied BMS 10-86 Teflon-filled coating (terminating action per AD 2002-26-15). We are issuing this AD to detect and correct wear damage and cracks of the fuselage skin in the interface area of the vertical stabilizer seal and fuselage skin in sections 46 and 48, which could cause in-flight depressurization of the airplane.
Airworthiness Directives; Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747SR, and 747SP Series Airplanes
Document Number: E8-23821
Type: Proposed Rule
Date: 2008-10-08
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747- 200C, 747-200F, 747-300, 747-400, 747SR, and 747SP series airplanes. This proposed AD would require inspecting for skin cracks at the shear tie end fastener locations of the fuselage frames, and repair if necessary. This proposed AD results from a wide-spread fatigue damage assessment of Model 747 airplanes. We are proposing this AD to detect and correct cracks in the fuselage skin that can propagate and grow, resulting in a loss of structural integrity and a sudden decompression of the airplane during flight.
Establishment of Class E Airspace; Lexington, OK
Document Number: E8-23777
Type: Rule
Date: 2008-10-08
Agency: Federal Aviation Administration, Department of Transportation
This action confirms the effective date of the direct final rule that established Class E airspace at Muldrow Army Heliport, Lexington, OK, published in the Federal Register August 6, 2008 (73 FR 45607) Docket No. FAA-2008-0003.
Amendment of Class E Airspace; Black River Falls, WI
Document Number: E8-23770
Type: Rule
Date: 2008-10-08
Agency: Federal Aviation Administration, Department of Transportation
This action confirms the effective date of the direct final rule that amended Class E airspace at Black River Falls, WI, published in the Federal Register August 6, 2008 (73 FR 45606) Docket No. FAA- 2008-0024.
Proposed Establishment of Class E Airspace; Edinburg, TX
Document Number: E8-23768
Type: Proposed Rule
Date: 2008-10-07
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to establish Class E airspace at South Texas International Airport, Edinburg, TX. Controlled airspace is necessary to accommodate Standard Instrument Approach Procedures (SIAP) at South Texas International Airport, Edinburg, TX. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) aircraft operations at South Texas International Airport.
Proposed Establishment of Class D and Class E Airspace; Conroe, TX
Document Number: E8-23753
Type: Proposed Rule
Date: 2008-10-07
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to establish Class D airspace and Class E Surface Area airspace at Lone Star Executive Airport, Conroe, TX. The establishment of an air traffic control tower has made these actions necessary for the safety of Instrument Flight Rule (IFR) operations at Lone Star Executive Airport. Class D airspace will revert to a Class E2 Surface Area during periods when the control tower is not operating.
Airworthiness Directives; Boeing Model 727 Airplanes
Document Number: E8-23668
Type: Proposed Rule
Date: 2008-10-07
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Boeing Model 727 airplanes. This proposed AD would require, among other actions, installing new ground fault interrupter (GFI) relays for the main fuel tanks and the auxiliary fuel tank pumps. This proposed AD also would require revising the FAA-approved maintenance program to incorporate new Airworthiness Limitations (AWLs) for the GFI of the boost pumps and for the uncommanded on system for the auxiliary fuel tank pumps. This proposed AD results from fuel system reviews conducted by the manufacturer. We are proposing this AD to prevent an electrical fault in the fuel pump system, which might cause a connector or end cap to burn through and a subsequent fire or explosion inside the fuel pump or wing spar area. We are also proposing this AD to prevent uncommanded operation of the auxiliary fuel tank pumps, which can cause them to run dry. This condition will increase pump temperature and could supply an ignition source to fumes in the fuel tank, which can result in a consequent fire or explosion.
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-120, -120ER, -120FC, -120QC, and -120RT Airplanes
Document Number: E8-23666
Type: Proposed Rule
Date: 2008-10-07
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Hawker Beechcraft Corporation Model BAe.125 Series 800A (including C-29A and U-125) Airplanes, and Hawker Beechcraft Model Hawker 800XP Airplanes
Document Number: E8-23400
Type: Rule
Date: 2008-10-07
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation Model BAe.125 series 800A (including C- 29A and U-125) airplanes, and Hawker Beechcraft Model Hawker 800XP airplanes. This AD requires doing an inspection to determine the serial number and part number on the main landing gear (MLG) upper casing, and replacing the MLG assembly with a serviceable MLG assembly if necessary. This AD results from a report indicating that the MLG casings have received improper hydrogen embrittlement relief. We are issuing this AD to prevent a fracture of the MLG casings and a collapse of the affected MLG, which could adversely affect the airplane's continued safe flight and landing.
Civil Supersonic Aircraft Panel Discussion
Document Number: E8-22898
Type: Notice
Date: 2008-10-07
Agency: Federal Aviation Administration, Department of Transportation
This notice advises interested persons that the FAA is participating in a panel session on civil supersonic aircraft research. The session will include presentations on current research programs and a question and answer session for attendees. The FAA is seeking to raise public awareness of the continuing technological advances in supersonic aircraft technology aimed at reducing the intensity of sonic boom.
Notice of Intent To Rule on Request To Release Airport Land at Nenana Airport, Nenana, AK
Document Number: E8-23563
Type: Notice
Date: 2008-10-06
Agency: Federal Aviation Administration, Department of Transportation
The Federal Aviation Administration (FAA) proposes to rule and invites public comment on the release of approximately 15.61 acres of airport property at Nenana Airport, Nenana, Alaska, from all restrictions of the surplus property agreement since the parcel of land is not needed for airport purposes. Reuse of the land for Alaska Rail Road track straightening represents a compatible land use. Sale of the property to the Alaska Rail Road at the appraised fair market value will be used to pay legal fees incurred during recent airport improvements. The property is not needed for airport purposes and reinvestment of the sale proceeds will benefit the airport and the interests of civil aviation.
Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG (RRD) Dart 528, 529, 532, 535, 542, and 552 Series Turboprop Engines; Correction
Document Number: E8-23511
Type: Rule
Date: 2008-10-06
Agency: Federal Aviation Administration, Department of Transportation
The FAA is correcting airworthiness directive (AD) 2008-16-05. That AD applies to RRD Dart 528, 529, 532, 535, 542, and 552 Series turboprop engines. We published that AD in the Federal Register on July 31, 2008 (73 FR 44630). The superseded AD number in paragraph (b) in the regulatory section is incorrect. This document corrects that superseded AD number. In all other respects, the original document remains the same.
Notice of Intent To Rule on Request To Abandon Tatum Airport, Tatum, NM
Document Number: E8-23262
Type: Notice
Date: 2008-10-02
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to rule and invites public comment on the abandonment of the Tatum Airport, Tatum, NM, under provisions of Title 49, U.S.C. Section 47107(h) and to release the State of New Mexico as airport sponsor from the Airport Improvement Program Grant Agreement Grant Assurances, and to change forever the lands of the Tatum Airport from aeronautical to non-aeronautical use. The State of New Mexico will transfer Tatum's grant obligations associated with AIP Grant Number 3- 35-0044-001-2002 obligations to Navajo Lake Airport, Navajo Dam NM by investing the grant funds of $27,362 for fencing at Tatum to a fencing project at Navajo Lake Airport.
Petition for Exemption; Summary of Petition Received
Document Number: E8-23234
Type: Notice
Date: 2008-10-02
Agency: Federal Aviation Administration, Department of Transportation
This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Automatic Dependent Surveillance-Broadcast (ADS-B) Out Performance Requirements To Support Air Traffic Control (ATC) Service; Reopening of Comment Period
Document Number: E8-23199
Type: Proposed Rule
Date: 2008-10-02
Agency: Federal Aviation Administration, Department of Transportation
On October 5, 2007, the FAA published a Notice of Proposed Rulemaking (NPRM) that proposed performance requirements for certain avionics equipment on aircraft operating in specified classes of airspace within the United States National Airspace System. The comment period closed on March 3, 2008. The FAA is reopening the comment period for an additional 30 days to give the public an opportunity to comment on recommendations received from an Aviation Rulemaking Committee established by the Administrator on July 15, 2007.
Airworthiness Standards; Aircraft Engine Standards for Pressurized Engine Static Parts; Correction
Document Number: E8-23140
Type: Rule
Date: 2008-10-02
Agency: Federal Aviation Administration, Department of Transportation
This document corrects the amendment number to a final rule published in the Federal Register of Thursday, September 25, 2008, regarding requirements for pressurized engine static parts.
Public Notice for Waiver of Aeronautical Land-Use Assurance; Mansfield Lahm International Airport, Mansfield, OH
Document Number: E8-22982
Type: Notice
Date: 2008-10-02
Agency: Federal Aviation Administration, Department of Transportation
The Federal Aviation Administration (FAA) is considering a proposal to change a portion of the airport from aeronautical use to non-aeronautical use and to authorize the sale of the airport property. The proposal consists of the sale of vacant, much of which is farmed or vacant, containing trees, streams, and scattered wetland areas owned by the City of Mansfield. The Miller Farm Parcel 50 is approximately 100.521 acres. The land was acquired under FAA Project No(s): AIP-90-2-3-39-0049-099l (Contract No. AlP FA91-GL-l806). There are no impacts to the airport by allowing the airport to dispose of the property. The proposed land for release is vacant, not required for future development, safety, or compatible land use. The intended land use is infrastructure development, including roads, utilities, and industrial development. Approval does not constitute a commitment by the FAA to financially assist in the disposal of the subject airport property nor a determination of eligibility for grant-in-aid funding from the FAA. The disposition of proceeds from the disposal of the airport property will be in accordance with FAA's Policy and Procedures Concerning the Use of Airport Revenue, published in the Federal Register on February 16, 1999. In accordance with section 47107(h) of title 49, United States Code, this notice is required to be published in the Federal Register 30 days before modifying the land-use assurance that requires the property to be used for an aeronautical purpose.
Airworthiness Directives; Boeing Model 737-300, -400, and -500 Series Airplanes
Document Number: E8-22755
Type: Rule
Date: 2008-10-01
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Boeing Model 737-300, -400, and -500 series airplanes. This AD requires repetitive external detailed inspections or non-destructive inspections to detect cracks in the fuselage skin along the chem-mill steps at stringers S-1 and S-2R, between station (STA) 400 and STA 460, and repair if necessary. This AD results from reports of cracks in the fuselage skin common to stringer S-1 and between STA 400 and STA 460. We are issuing this AD to detect and correct fatigue cracking of the fuselage skin panels at the chem-mill steps, which could result in sudden fracture and failure of the fuselage skin panels, and consequent rapid decompression of the airplane.
Airworthiness Directives; Boeing Model 737-100, -200, -200C, -300, -400, and -500 Series Airplanes
Document Number: E8-22649
Type: Rule
Date: 2008-10-01
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Boeing Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This AD requires replacing the existing straight-to-90- degree hose assembly for the Lavatory ``A'' water supply. The replacement is a new straight hose assembly and a separate 90-degree elbow fitting. This AD results from a report of a separated hose assembly for the passenger water system. We are issuing this AD to prevent a water leak into the flight deck ceiling, which could result in an electrical short and possible loss of several functions essential to safe flight.
Airworthiness Directives; Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-300, 747-400, 747-400D, and 747SR Series Airplanes
Document Number: E8-20091
Type: Rule
Date: 2008-10-01
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747- 300, 747-400, 747-400D, and 747SR series airplanes. For certain airplanes, this AD requires a material type inspection to determine if the lower forward corner reveal of the number 3 main entry doors (MEDs) is a casting. If the reveals are castings, this AD requires repetitive inspections of the reveals for cracking, and corrective action if necessary. If the reveals are not castings, this AD requires a detailed inspection of the reveals for a sharp edge and repetitive inspections of the reveals for cracking, and corrective action if necessary. For certain other airplanes, this AD requires only a detailed inspection of the reveals for a sharp edge and repetitive inspections of the reveals for cracking, and corrective action if necessary. For certain other airplanes, this AD requires repetitive inspections of the reveals for cracking only, and corrective action if necessary. This AD also allows a certain replacement as an optional action for the material type inspection for certain airplanes. This AD results from reports of cracking and/or a sharp edge in the lower forward corner reveal of the number 3 MEDs. We are issuing this AD to detect and correct fatigue cracking of the lower forward corner reveal of the number 3 MEDs, which could lead to the door escape slide departing the airplane when the door is opened and the slide is deployed, and consequent injuries to passengers and crew using the door escape slide during an emergency evacuation.
Tenth Meeting, Special Committee 215 Aeronautical Mobile Satellite (Route) Services Next Generation Satellite Services and Equipment
Document Number: E8-22983
Type: Notice
Date: 2008-09-30
Agency: Federal Aviation Administration, Department of Transportation
The FAA is issuing this notice to advise the public of a second meeting of RTCA Special Committee 215, Aeronautical Mobile Satellite (Route) Services, Next Generation Satellite Services and Equipment.
Airworthiness Directives; Saab Model SAAB-Fairchild SF340A (SAAB/SF340A) and SAAB 340B Airplanes
Document Number: E8-22915
Type: Proposed Rule
Date: 2008-09-30
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; 328 Support Services GmbH Dornier Model 328-100 Airplanes
Document Number: E8-22907
Type: Proposed Rule
Date: 2008-09-30
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Notice of Intent To Rule on Request To Release Airport Property at the Warren County Memorial Airport, McMinnville, TN
Document Number: E8-22718
Type: Notice
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
The Federal Aviation Administration is requesting public comment on the release of land at the Warren County Memorial Airport in the City of McMinnville, Tennessee. This property, approximately 13.3 acres, will change to a non-aeronautical use. This action is taken under the provisions of Section 125 of the Wendell H. Ford Aviation Investment Reform Act for the 21st Century (AIR 21).
Revision of and Revocation to Compulsory Reporting Points; Alaska
Document Number: E8-22648
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
This action revises the published description of three low altitude Alaskan compulsory reporting points, two high altitude reporting points, and revokes one high and low altitude reporting point in the vicinity of Bethel and Ketchikan. Specifically, the FAA is revising the description of CRACK, GARRS and MOCHA to address recent technical adjustments to their actual locations. Additionally, the FAA has determined that the FLUKE reporting point is no longer needed in the National Airspace System (NAS).
Airworthiness Directives; Rolls-Royce plc RB211 Series Turbofan Engines
Document Number: E8-22521
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Establishment of Class D Airspace; Victoria, TX
Document Number: E8-22455
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
This action establishes Class D airspace at Victoria Regional Airport, Victoria, TX. Establishment of an air traffic control tower has made this action necessary for the safety of Instrument Flight Rule (IFR) operations at Victoria Regional Airport.
Modification of Class D and E Airspace; Brunswick, ME
Document Number: E8-22452
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
This action modifies Class D and E Airspace at Brunswick, ME. The Brunswick NAS Air Traffic Control Tower operates on an other than a full time basis; therefore, the Class D Airspace and its extensions associated with the tower operations must be modified to reflect the times when the controlled airspace is effective. This action enhances the National Airspace System by relaxing the restrictions to the controlled airspace areas in the vicinity of Brunswick, ME.
Amendment to Class E Airspace; Windsor Locks, Bradley International Airport, CT
Document Number: E8-22450
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
This action revises the Class E Airspace at Windsor Locks, Bradley International Airport, CT (BDL) to provide for adequate controlled airspace for those aircraft using Instrument Approach Procedures to the airport. The CHUPP NDB has been decommissioned, and after evaluation of the extension to the Windsor Locks Class C airspace defined using the CHUPP NDB, the FAA determined that the Class E3 airspace should be retained and extended 1 mile to provide adequate controlled airspace for the Instrument Approach Procedures to BDL. This action will enhance the safety and airspace management around the Bradley International Airport.
Proposed Amendment of Class E Airspace; Big Spring, TX
Document Number: E8-22448
Type: Proposed Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to amend Class E airspace at Big Spring McMahon Wrinkle Airport, Big Spring, TX. Additional controlled airspace is necessary to accommodate changes to the VOR/DME RWY 17 Standard Instrument Approach Procedure (SIAP) at Big Spring McMahon-Wrinkle Airport, Big Spring, TX. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) aircraft operations at Big Spring McMahon-Wrinkle Airport.
Establishment of Class E Airspace; Plains, TX
Document Number: E8-22445
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
This action confirms the effective date of the direct final rule that establishes Class E5 airspace at Plains, TX, published in the Federal Register July 7, 2008, (73 FR 38313) Docket No. FAA-2008-0683.
Amendment of Class E Airspace; Butler, PA; Removal of Class E Airspace; East Butler, PA
Document Number: E8-22443
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E Airspace at Butler, PA to merge the existing Class E Airspace listed under East Butler, PA, which will be removed. The protected airspace that was developed for an Area Navigation (RNAV) Global Positioning System (GPS) Special Instrument Approach Procedure (lAP) for medical flight operations into Butler Memorial Hospital Heliport, PA was erroneously listed under East Butler, PA. This action corrects that mistake by listing all applicable airspace under the correct location of Butler, PA. Additionally, this action imparts a technical amendment by correctly listing the Butler County Airport as Butler Co./K W Scholter Field Airport.
Airworthiness Directives; Fokker Model F.28 Mark 0070 and Mark 0100 Airplanes
Document Number: E8-22210
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Fokker Model F.28 Mark 0070 and 0100 airplanes. That AD currently requires a one-time inspection of the main landing gear (MLG) main fitting for cracks, and repair if necessary. The existing AD also currently requires installing a placard and revising the airplane flight manual to include procedures to prohibit the application of brakes during backward movement of the airplane. This new AD requires repetitive eddy current inspections of the MLG main fitting and rework before further flight as applicable. This AD results from reports that a final solution eliminating the cause of the crack initiation mechanism is not yet available and that repetitive inspections are necessary. We are issuing this AD to detect and correct cracks in the MLG main fitting, which could result in reduced structural integrity of the MLG main fitting.
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 and ERJ 190 Airplanes
Document Number: E8-22205
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Fokker Model F.28 Mark 0070 and 0100 Airplanes
Document Number: E8-22065
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier Model DHC-8-400, DHC-8-401, and DHC-8-402 Airplanes
Document Number: E8-22061
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Lockheed Model 382, 382B, 382E, 382F, and 382G Series Airplanes
Document Number: E8-22035
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all Lockheed Model 382, 382B, 382E, 382F, and 382G series airplanes. This AD requires revising the FAA-approved maintenance program by incorporating new airworthiness limitations for fuel tank systems to satisfy Special Federal Aviation Regulation No. 88 requirements. This AD also requires the accomplishment of certain fuel system modifications, the initial inspections of certain repetitive fuel system limitations to phase in those inspections, and repair if necessary. This AD results from a design review of the fuel tank systems. We are issuing this AD to prevent the potential for ignition sources inside fuel tanks caused by latent failures, alterations, repairs, or maintenance actions, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Amendment of Class D and Class E Airspace; Altus AFB, OK
Document Number: E8-21518
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
This action changes the effective date and makes a correction to the direct final rule that amends Class D and Class E airspace at Altus AFB, OK, published in the Federal Register August 6, 2008 (73 FR 45605) Docket No. FAA-2008-0339. The effective date is changed to November 20, 2008, to allow additional time for charting. This action also makes a correction to the geographic coordinates of Altus AFB.
Airworthiness Directives; ATR Model ATR42-200, -300, and -320 Airplanes
Document Number: E8-19365
Type: Rule
Date: 2008-09-29
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Establishment of Class E Airspace; Pampa, TX
Document Number: E8-22719
Type: Rule
Date: 2008-09-26
Agency: Federal Aviation Administration, Department of Transportation
This action confirms the effective date and makes a correction to the direct final rule that establishes Class E airspace at Pampa, Mesa Vista Ranch Airport, TX, published in the Federal Register July 7, 2008 (73 FR 38314) Docket No. FAA-2008-0610. This action corrects the final rule by adding ``Mesa Vista Ranch Airport'' to more clearly define the airport name in the airport description.
Modification and Establishment of Restricted Areas and Other Special Use Airspace, Adirondack Airspace Complex; Fort Drum, NY
Document Number: E8-22646
Type: Rule
Date: 2008-09-26
Agency: Federal Aviation Administration, Department of Transportation
This action restructures the restricted areas and other special use airspace (SUA) located in the vicinity of Fort Drum, NY. The Air National Guard (ANG) requested redesign of existing restricted airspace R-5201, known as the Adirondack Airspace Complex, by establishing two new restricted areas: R-5202A and R-5202B, and by restructuring the military operations areas (MOA) contained in the Adirondack Airspace Complex. Unlike restricted areas, which are designated under 14 CFR part 73, MOAs are not rulemaking airspace actions. However, since these MOAs form an integral part of the Adirondack Airspace Complex, the FAA is including a description of the associated MOA changes in this rule. The MOA changes described here will also be published in the National Flight Data Digest (NFDD). The ANG requested these airspace changes to provide the additional SUA needed to conduct more realistic aircrew training in the Adirondack Airspace Complex.
Airworthiness Directives; Airbus Model A310 Series Airplanes and Model A300-600 Series Airplanes
Document Number: E8-22632
Type: Proposed Rule
Date: 2008-09-26
Agency: Federal Aviation Administration, Department of Transportation
The FAA is revising an earlier NPRM for an airworthiness directive (AD) that applies to all Airbus Model A310 series airplanes and Model A300-600 series airplanes. The original NPRM would have required superseding two existing ADs. One existing AD applies to certain Airbus Model A310 series airplanes and currently requires repetitive inspections for cracking of the flap transmission shafts, and replacement of the transmission shafts if necessary. That existing AD also provides an optional terminating action for the repetitive inspections. The other existing AD applies to all Airbus Model A310 and A300-600 series airplanes and currently requires a one-time inspection of the trimmable horizontal stabilizer actuator, corrective actions if necessary, and follow-on repetitive tasks. The original NPRM would have added revising the Airworthiness Limitations Section of the Instructions for Continued Airworthiness to incorporate new limitations and maintenance tasks for aging systems maintenance. The original NPRM resulted from the manufacturer's determination that life limitations and maintenance tasks are necessary in order to ensure continued operational safety of the affected airplanes. This new action revises the original NPRM by reducing the initial compliance times. We are proposing this supplemental NPRM to prevent reduced structural integrity of these airplanes due to the failure of system components.
Notice of Availability of Draft Environmental Impact Statement (DEIS) Containing a Notice of Public Comment Period and Schedule for a Public Information Workshop and Public Hearing for Proposed New Air Carrier Runway 9R/27L and Associated Developments at Palm Beach International Airport (PBIA)
Document Number: E8-22631
Type: Notice
Date: 2008-09-26
Agency: Federal Aviation Administration, Department of Transportation
The Federal Aviation Administration (FAA) is issuing this notice to advise the public that a Draft Environmental Impact Statement (DEIS) for the Proposed New Runway and Associated Development at Palm Beach International Airport, has been prepared and is available for public review and comment. Your written comments on the DEIS and related documents can be sent to the individual listed in the section FOR FURTHER INFORMATION CONTACT. A Public Information Workshop and Public Hearing will be held on November 12, 2008. The public comment period will commence on September 26, 2008 and will close on November 24, 2008. Public Comment and Information Workshop/Public Hearing: The start of the public comment period on the DEIS and associated studies will start on September 26, 2008 and will close on November 24, 2008. A Public Information Workshop and Public Hearing will be held on November 12, 2008 in West Palm Beach. The purpose of the Public Information Workshop and Public Hearing and the public comment period is to comply with NEPA requirements to provide public disclosure and involvement concerning the scope and content of the DEIS, and to afford the public and other interested parties the opportunity to comment on the economic, social, and environmental effects of the proposed project and its consistency with the objectives of any planning that the community has carried out. The Public Information Workshop will begin at 4 p.m. (EST) and will end at 7 p.m. (EST). The Public Hearing will begin at 6 p.m. (EST) and run concurrently with the Public Information Workshop. The Public Information Workshop/Public Hearing will be held at the Palm Beach County Convention Center, Second Floor, 650 Okeechobee Boulevard, West Palm Beach, FL 33401. You can review copies of the DEIS and related documents may be viewed during regular business hours at the following locations: 1. PBC Library Main Branch, 3650 Summit Boulevard, West Palm Beach, FL 33406. 2. PBC Library Greenacres Branch, 3750 Jog Road, Greenacres, FL 33467. 3. PBC Library Okeechobee Boulevard Branch, 5689 West Okeechobee Boulevard, West Palm Beach, FL 33417. 4. WPB Public Library, 100 Clematis Street, West Palm Beach, FL 33401. Copies of the DEIS and related documents will also be available for review by appointment only at the following FAA and Palm Beach County Department of Airports offices: Federal Aviation Administration, Orlando Airports District Office, 5950 Hazeltine National Drive, Citadel International Building, Suite 400, Orlando, FL, (407) 812-6331; Palm Beach International Airport, Palm Beach County Department of Airports Office, 846 Palm Beach International Airport, West Palm Beach, FL, (561) 471-7412. Please schedule an appointment to review the DEIS in advance. A copy of the DEIS will also be available September 26, 2008 on the project Web site at http://www.pbia-eis.com.
Advisory Circular 120-16E, Air Carrier Maintenance Programs
Document Number: E8-22630
Type: Notice
Date: 2008-09-26
Agency: Federal Aviation Administration, Department of Transportation
This notice announces the issuance and availability of Advisory Circular (AC) 120-16E, ``Air Carrier Maintenance Programs''. This advisory circular (AC) is an update of AC 120-16D that was issued in 2003. It describes the scope, content, and functions of air carrier aircraft maintenance programs. It explains the background of these programs as well as the Federal Aviation Administration's regulatory requirements. Each of the 10 elements of air carrier maintenance programs is also described and explained. The material in this AC is not mandatory and does not constitute a regulation. However, when ``must'' or ``will'' are used in this AC, such use reflects actual regulatory requirements.