National Highway Traffic Safety Administration – Federal Register Recent Federal Regulation Documents

Ford Motor Company (Ford) has determined that certain model year 2011 Ford E-150, E-250, E-350 and E-450 motor vehicles manufactured between May 12, 2011 and May 26, 2011, do not fully comply with paragraph S5.1.1 of Federal Motor Vehicle Safety Standard (FMVSS) No. 205, Glazing Materials. Ford has filed an appropriate report pursuant to 49 CFR Part 573, Defect and Noncompliance Responsibility and Reports, dated August 22, 2011. Pursuant to 49 U.S.C. 30118(d) and 30120(h) (see implementing rule at 49 CFR part 556), Ford has petitioned for an exemption from the notification and remedy requirements of 49 U.S.C. Chapter 301 on the basis that this noncompliance is inconsequential to motor vehicle safety. NHTSA published a notice of receipt of the petition, with a 30-day public comment period, on February 2, 2012, in the Federal Register 77 FR 5301. In response to the petition, NHTSA did not receive any comments.

Completing the first initiative of NHTSA's 2007 ``NHTSA's Approach to Motorcoach Safety'' plan and one of the principal undertakings of DOT's 2009 Motorcoach Safety Action Plan, and fulfilling a statutory mandate of the Motorcoach Enhanced Safety Act of 2012, incorporated into the Moving Ahead for Progress in the 21st Century Act, this final rule amends the Federal motor vehicle safety standard (FMVSS) on occupant crash protection to require lap/shoulder seat belts for each passenger seating position in all new over-the-road buses, and in new buses other than over-the-road buses with a gross vehicle weight rating (GVWR) greater than 11,793 kilograms (kg) (26,000 pounds (lb), with certain exclusions. By requiring the passenger lap/ shoulder seat belts, this final rule significantly reduces the risk of fatality and serious injury in frontal crashes and the risk of occupant ejection in rollovers, thus considerably enhancing the safety of these vehicles.

This document proposes to amend our regulations to add specifications and qualification requirements for an anthropomorphic test device (ATD) representing a 3-year-old child, called the ``Q3s'' side impact test dummy. The agency plans to use the Q3s to test child restraint systems to new side impact performance requirements which NHTSA will propose to adopt into the Federal motor vehicle safety standard for child restraint systems by way of a separate NPRM. Adopting side impact protection requirements is consistent with a statutory provision set forth in the ``Moving Ahead for Progress in the 21st Century Act'' (July 6, 2012), that the agency issue a final rule to improve the protection of children seated in child restraint systems during side impacts.

Before a Federal agency can collect certain information from the public, it must receive approval from the Office of Management and Budget (OMB). Under procedures established by the Paperwork Reduction Act of 1995, before seeking OMB approval, Federal agencies must solicit public comment on proposed collections of information, including extensions and reinstatements of previously approved collections. This document describes the collection of information for which NHTSA intends to seek OMB approval.

The NHTSA announces meetings of NEMSAC and FICEMS to be held consecutively in the Metropolitan Washington, DC, area. This notice announces the date, time, and location of the meetings, which will be open to the public, as well as opportunities for public input to the NEMSAC and FICEMS. The purpose of NEMSAC, a nationally recognized council of emergency medical services representatives and consumers, is to advise and consult with DOT and the FICEMS on matters relating to emergency medical services (EMS). The purpose of FICEMS is to ensure coordination among Federal agencies supporting EMS and 9-1-1 systems.

This document grants in full the Porsche Cars North America, Inc. (Porsche) petition for exemption of the Macan vehicle line in accordance with 49 CFR part 543, Exemption From Vehicle Theft Prevention Standard. This petition is granted because the agency has determined that the antitheft device to be placed on the line as standard equipment is likely to be as effective in reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of the 49 CFR part 541, Federal Motor Vehicle Theft Prevention Standard.

Jaguar Land Rover North America, LLC, on behalf of Jaguar Cars Limited (collectively referred to as ``Jaguar'') has determined that model year 2010 and certain 2011 Jaguar XJ passenger cars manufactured between September 11, 2009 and March 28, 2011, do not fully comply with paragraphs S5.2.1 and S5.5.2 of Federal Motor Vehicle Safety Standard (FMVSS) No. 101, Controls and displays, regarding brake system-related telltales. Jaguar has filed an appropriate report pursuant to 49 CFR Part 573, Defect and Noncompliance Responsibility and Reports, dated April 15, 2011.

This document announces receipt by the National Highway Traffic Safety Administration (NHTSA) of a petition for a decision that nonconforming 1992 Jeep Wrangler Multi-Purpose Passenger Vehicles that were not originally manufactured to comply with all applicable Federal Motor Vehicle Safety Standards (FMVSS), are eligible for importation into the United States because they are substantially similar to vehicles that were originally manufactured for sale in the United States and that were certified by their manufacturer as complying with the safety standards (1992 Jeep Wrangler Multi-Purpose Passenger Vehicles) and they are capable of being readily altered to conform to the standards.

General Motors, LLC (GM) has determined that certain model year (MY) 2013 Chevrolet Equinox multipurpose passenger vehicles (MPVs) manufactured on January 24, 2013 do not fully comply with paragraph S6 of Federal Motor Vehicle Safety Standard (FMVSS) No. 205, Glazing Materials. GM has filed an appropriate report dated February 22, 2013, pursuant to 49 CFR Part 573, Defect and Noncompliance Responsibility and Reports.

This notice announces NHTSA's publication of a Technical Report reviewing and evaluating certified-advanced air bags. The report's title is: Evaluation of the Certified-Advanced Air Bags.

In compliance with the Paperwork Reduction Act of 1995 (44 U.S.C. chapter 35), this notice announces that the Information Collection Request (ICR) abstracted below will be submitted to the Office of Management and Budget (OMB) for review. The ICR describes the nature of the information collection and its expected burden. A Federal Register Notice with a 60-day comment period soliciting public comments on the following information collection was published on August 5, 2013 (Federal Register/Vol. 78, No. 150/pp. 47488-47489).

This document announces the agency's decision to implement (with minor modifications) the planned update to the U.S. New Car Assessment Program (NCAP) that the agency announced in its June 26, 2013 request for comments (78 FR 38266). As we discussed in that request for comments, this update will enhance the program's ability to recommend to consumers vehicle models that have rearview video systems that the agency believes (based on currently available data) will decrease the risk of backover crashes. Further, the program will no longer list electronic stability control (ESC) as a Recommended Advanced Technology Feature because ESC is now required for all light vehicles. For many years, NCAP has provided comparative information on the safety of new vehicles to assist consumers with vehicle purchasing decisions. NCAP was most recently upgraded for model year 2011 to include recommended crash avoidance technologies. Those updates, along with today's updates to NCAP, allow consumers to better distinguish not only which vehicle models have advanced crash avoidance safety features but also which of these advanced features are best able to help them avoid crashes.

PACCAR Inc. (PACCAR) has determined that certain model year (MY) 2013 Kenworth and Peterbilt trucks, do not fully comply with paragraph S3.1.3 of Federal Motor Vehicle Safety Standard (FMVSS) No. 102, Transmission Shift Position Sequence, Starter Interlock, and Transmission Braking Effect. PACCAR has filed an appropriate revised report dated March 1, 2013, pursuant to 49 CFR Part 573, Defect and Noncompliance Responsibility and Reports.

Nissan North America, Inc. (Nissan) has determined that certain model year (MY) 2009 through 2012 Nissan Titan trucks manufactured from January 31, 2008 to July 17, 2012 and MY 2012 Nissan NV trucks, buses or multipurpose passenger vehicles (MPVs) manufactured from December 20, 2010 to July 17, 2012, do not fully comply with paragraph S3.1.4.1 of Federal Motor Vehicle Safety Standard (FMVSS) No. 102, Transmission Shift Position Sequence, Starter Interlock, and Transmission Braking Effect. Nissan has filed an appropriate report dated July 23, 2012, pursuant to 49 CFR part 573, Defect and Noncompliance Responsibility and Reports.

This document announces receipt by the National Highway Traffic Safety Administration (NHTSA) of a petition for a decision that nonconforming 1988-1996 Alpina B10 passenger cars that were not originally manufactured to comply with all applicable Federal Motor Vehicle Safety Standards (FMVSS), are eligible for importation into the United States because they have safety features that comply with, or are capable of being altered to comply with, all such standards.

Before a Federal agency can collect certain information from the public, it must receive approval from the Office of Management and Budget (OMB). Under procedures established by the Paperwork Reduction Act of 1995, before seeking OMB approval, Federal agencies must solicit public comment on proposed collections of information, including extensions and reinstatement of previously approved collections. This document describes one collection of information for which NHTSA intends to seek OMB approval.

This document responds to petitions for reconsideration of a 2011 final rule that established Federal Motor Vehicle Safety Standard (FMVSS) No. 226, ``Ejection mitigation.'' The standard is intended to reduce complete and partial ejections of vehicle occupants through side windows in crashes, particularly rollover crashes. Generally, the issues raised by the petitioners are of two types. The petitioners ask for reconsideration of policy issues relating to the agency's implementation of the standard, and of technical issues concerning engineering aspects of the rule, particularly as to how the compliance test procedure should be conducted or improved. Most of the requested changes were of the latter type. In general, NHTSA is denying the petitions for reconsideration. The few changes we have made in response to the petitions are minor, mostly to clarify the requirements of the standard.

Before a Federal agency can collect certain information from the public, it must receive approval from the Office of Management and Budget (OMB). Under procedures established by the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.), before seeking OMB approval, Federal agencies must solicit public comment on proposed collections of information, including extensions and reinstatements of previously approved collections. This document describes an Information Collection Request (ICR) for which NHTSA intends to seek OMB approval.

Before a Federal agency can collect certain information from the public, it must receive approval from the Office of Management and Budget (OMB). Under procedures established by the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.), before seeking OMB approval, Federal agencies must solicit public comment on proposed collections of information, including extensions and reinstatements of previously approved collections. This document describes an Information Collection Request (ICR) for which NHTSA intends to seek OMB approval.

This Notice provides NHTSA's finding that a waiver of the Buy America requirements is appropriate for the purchase of Can-Am Spyder motorcycles by the Wisconsin Department of Transportation (WisDOT), using Federal grant funds, for use as training vehicles in its Motorcycle Safety Program. NHTSA has determined that a waiver is appropriate because there are no comparable three-wheeled ``trike'' motorcycles produced domestically that use the same wheel configuration as the Spyder.

Before a Federal agency can collect certain information from the public, the agency must receive approval from the Office of Management and Budget (OMB). Under procedures established by the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.), before seeking OMB approval, Federal agencies must solicit public comment on proposed collections of information, including extensions and reinstatements of previously approved collections. In compliance with the Paperwork Reduction Act of 1995, this notice describes one collection of information for which NHTSA intends to seek OMB approval, relating to confidential business information.

This document revises the list of vehicles not originally manufactured to conform to the Federal Motor Vehicle Safety Standards (FMVSS) that NHTSA has decided to be eligible for importation. This list is published in an appendix to the agency's regulations that prescribe procedures for import eligibility decisions. The list has been revised to add all vehicles that NHTSA has decided to be eligible for importation since October 1, 2012, and to remove all previously listed vehicles that are now more than 25 years old and need no longer comply with all applicable FMVSS to be lawfully imported. NHTSA is required by statute to publish this list annually in the Federal Register.

This document grants in full the Chrysler LLC, (Chrysler) petition for exemption of the Chrysler [confidential] vehicle line in accordance with 49 CFR Part 543, Exemption from Vehicle Theft Prevention Standard. This petition is granted because the agency has determined that the antitheft device to be placed on the line as standard equipment is likely to be as effective in reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of the Theft Prevention Standard 49 CFR Part 541, Federal Motor Vehicle Theft Prevention Standard. Chrysler requested confidential treatment for specific information in its petition. The agency will address Chrysler's request for confidential treatment by separate letter.

This document grants in full Fuji Heavy Industries U.S.A., Inc.'s (FUSA) petition for exemption of the Subaru [confidential] vehicle line in accordance with 49 CFR part 543, Exemption from the Theft Prevention Standard. This petition is granted because the agency has determined that the antitheft device to be placed on the line as standard equipment is likely to be as effective in reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of the Theft Prevention Standard 49 CFR part 541, Federal Motor Vehicle Theft Prevention Standard. FUSA requested confidential treatment for specific information in its petition. The agency has addressed FUSA's request for confidential treatment by letter dated June 28, 2013. However, FUSA has stated that it will provide the agency with the nameplate of the vehicle prior to its introduction for sale into commerce in order to allow the agency to notify law enforcement agencies and the public of a new vehicle line exempted from the parts- marking requirements of the Theft Prevention Standard.

Dorel Juvenile Group, Inc. (DJG) has determined that certain child restraint systems manufactured between July 20, 2010 and May 18, 2011 do not fully comply with paragraph S5.5.2(l) of Federal Motor Vehicle Safety Standard (FMVSS) No. 213, Child Restraint Systems (49 CFR 571.213). DJG has filed an appropriate report pursuant to 49 CFR Part 573, Defect and Noncompliance Responsibility and Reports, dated July 19, 2011. Pursuant to 49 U.S.C. 30118(d) and 30120(h) (see implementing rule at 49 CFR part 556), DJG has petitioned for an exemption from the notification and remedy requirements of 49 U.S.C. Chapter 301 on the basis that this noncompliance is inconsequential to motor vehicle safety. Notice of receipt of the petition was published, with a 30-day comment period, on January 19, 2012 in the Federal Register (77 FR 2776). NHTSA received one comment from Consumers Union (CU). To view the petition, the comment, and all supporting documents log onto the Federal Docket Management System (FDMS) Web site at: https:// www.regulations.gov/. Then follow the online search instructions to locate docket number ``NHTSA-2012-0002.'' Contact Information: For further information on this decision, contact Mr. Zachary R. Fraser, Office of Vehicle Safety Compliance, the National Highway Traffic Safety Administration (NHTSA), telephone (202) 366-5754, facsimile (202) 366-7002. Equipment Involved: Affected are approximately 89,527 of the following models of DJG child restraint systems that were manufactured between July 20, 2010 and May 18, 2011: