Federal Aviation Administration 2025 – Federal Register Recent Federal Regulation Documents

This action revokes the Class D and Class E airspace in the Republic of the Marshall Islands (RMI). RMI is an independent nation, and the FAA does not have regulatory authority to establish or amend domestic airspace pursuant to Title 14 Code of Federal Regulations (14 CFR) part 71 over RMI's land or territorial waters.

This action proposes to modify the Class D surface area airspace, Class E airspace area designated as surface area, Class E airspace areas designated as an extension to a Class D or Class E surface area, and the Class E airspace area extending upward from 700 feet above the surface of the earth at Bozeman Yellowstone International Airport, Bozeman, MT. These actions would support the safety and management of visual flight rules (VFR) and instrument flight rules (IFR) operations at the airport.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on October 21, 2024. The collection involves the submission of FAA Form 8710-3 for the certification process of agricultural aircraft operators, and other reporting and recordkeeping activities required of agricultural aircraft operators. The information to be collected is necessary to evaluate the applicants' qualifications for certification. This collection also involves the submission of information in petitions for exemption by agricultural aircraft operators, plans for operations over congested areas, and recordkeeping requirements for agricultural aircraft operators.

This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion nor omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A321-251NX, -252NX, -253NX, -271NX, and -272NX airplanes. This proposed AD was prompted by discovery of two bushes that had migrated on the latch shaft of an emergency overwing exit door (OWED) during accomplishment of an inspection on an in-service airplane. This proposed AD would require repetitive detailed inspections (DETs) of the affected parts and, in case of discrepancies, modification of the affected parts, and would prohibit the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.

This action proposes to establish Class E airspace extending upward from 700 feet above the surface for Sunbury, NC, by adding airspace for Sunbury Fire Department Heliport, Sunbury, NC. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations at this heliport.

This action establishes Class E airspace at Victoria, TX to support new public instrument procedures.

This action establishes Class E airspace extending upward from 700 feet above the surface for Transylvania Community Hospital, Brevard, NC, to accommodate new area navigation (RNAV) global positioning system (GPS) standard instrument approach procedures serving the heliport. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations at this heliport.

This action proposes to amend the Class E airspace at Beckley, WV. The FAA is proposing this action as the result of an airspace review conducted due to the decommissioning of the Beckley very high frequency omnidirectional range (VOR) as part of the VOR Minimum Operational Network (MON) Program. This action will bring the airspace into compliance with FAA orders and support instrument flight rule (IFR) procedures and operations.

This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion nor omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion nor omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

The FAA is superseding Airworthiness Directive (AD) 2023-23- 09, which applied to all Embraer S.A. Model ERJ 190-400 airplanes. AD 2023-23-09 required repetitive inspections of the press-fitted bushings of the wing ailerons for migration and broken sealant, measurements of the distance between the aileron surfaces and hinge fittings, functional checks of the backlash of the wing aileron control system, and all applicable related investigative and corrective actions. Since the FAA issued AD 2023-23-09, it was determined that certain requirements needed to be clarified. This AD continues to require all actions of ANAC AD 2023-05-02 with revised compliance requirements, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 757 airplanes. This AD was prompted by reports of several occurrences of a power transfer unit (PTU) control valve that failed to open when commanded. This AD requires installing new relays and changing certain wire bundles leading to the PTU control valve. The FAA is issuing this AD to address the unsafe condition on these products.

This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPS) and associated Takeoff Minimums and Obstacle Departure procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 767-200, -300, and -300F airplanes. This AD was prompted by a report of a main landing gear (MLG) collapse event following maintenance where a grinder was operating outside of its input parameters, resulting in possible heat damage to the outer cylinder of the MLG. This AD requires replacing affected outer cylinders. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) Model GEnx-1B64, GEnx-1B64/P1, GEnx-1B64/P2, GEnx-1B67, GEnx-1B67/P1, GEnx-1B67/P2, GEnx-1B70, GEnx- 1B70/75/P1, GEnx-1B70/75/P2, GEnx-1B70/P1, GEnx-1B70/P2, GEnx-1B70C/P1, GEnx-1B70C/P2, GEnx-1B74/75/P1, GEnx-1B74/75/P2, GEnx-1B76/P2, GEnx- 1B76A/P2, GEnx-2B67, GEnx-2B67B, and GEnx-2B67/P engines. This AD was prompted by a manufacturer evaluation that determined a lower life limit may be necessary for certain stages 6-10 compressor rotor spools than allowed by the engine shop manual (ESM). This AD requires a one- time inspection of the stages 6-10 spools for previously accomplished blend repairs, a one-time inspection of the blend repairs on the stages 6-10 spools for compliance with the updated allowable limits, and replacement if necessary. The FAA is issuing this AD to address the unsafe condition on these products.

This action proposes to modify the Class E airspace area designated as surface area, establish a Class E airspace area designated as an extension to a Class D or Class E surface area, modify Class E airspace extending upward from 700 feet above the surface of the earth, and remove Class E airspace extending upward from 1,200 feet above the surface at Battle Mountain Airport, Battle Mountain, NV. Additionally, this action proposes administrative amendments to update the airport's existing Class E airspace legal descriptions. These actions would support the safety and management of instrument flight rules (IFR) operations at the airport.

This action amends the Class E airspace at Giddings, TX. This action is the result of airspace reviews conducted due to the decommissioning of the Industry very high frequency omnidirectional range (VOR) as part of the VOR Minimum Operational Network (MON) Program. The geographic coordinates of the airport are also being updated to coincide with the FAA's aeronautical database. This action brings the airspace into compliance with FAA orders and supports instrument flight rule (IFR) operations and procedures.

This action amends the Class E airspace at El Dorado, AR. This action is the result of an airspace review conducted due to the development of new instrument procedures. The geographic coordinates and name of the airport and the name of the El Dorado VOR/DME are also being updated to coincide with the FAA's aeronautical database. This action brings the airspace into compliance with FAA orders and support instrument flight rule (IFR) procedures and operations.

This action amends the Class E airspace at Pontiac, IL. This action is the result of an airspace review conducted due to the decommissioning of the Pontiac very high frequency omnidirectional range (VOR) as part of the VOR Minimum Operational Network (MON) Program. The geographic coordinates of the airport are also being updated to coincide with the FAA's aeronautical database. This action brings the airspace into compliance with FAA orders and supports instrument flight rule (IFR) procedures and operations.

This action establishes Class E airspace at Ashley, ND. This action is due to the development of new public instrument procedures at Ashley Municipal Airport, Ashley, ND, and to support instrument flight rule (IFR) operations.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This proposed AD was prompted by reports of engine-driven pump hydraulic pressure hoses for hydraulic systems number 1 and 2 chafing against the pylon in the aft equipment bay. This proposed AD would require an inspection of the engine-driven pump pressure hoses for any damage and minimum clearance between the engine-driven pump hydraulic pressure hose and case drain, suction pressure hose, and surrounding pylon structure; and corrective actions if necessary. The FAA is proposing this AD to address the unsafe condition on these products.

On October 8, 2024, the FAA published a final rule that will require individuals with foreign addresses and no U.S. physical address on file with the FAA who apply for certain certificates, ratings, or authorizations to designate a U.S. agent for service. This final rule extends the deadline for those individuals to designate a U.S. agent for service from January 6, 2025, to April 2, 2025. This final rule does not apply to individuals with foreign addresses who currently hold certain certificates, ratings, or authorizations, as the compliance date for those individuals continues to be July 7, 2025.

The FAA is adopting a new airworthiness directive (AD) for all Leonardo S.p.a. Model AB139 and AW139 helicopters. This AD was prompted by reports of broken main landing gear (MLG) shock absorber piston rod eye ends. This AD requires repetitively inspecting the MLG shock absorber piston rod eye ends, reporting the results of the inspection, and, depending on the results, replacing the MLG shock absorber assembly. It also prohibits installing certain MLG shock absorber assemblies unless specific requirements are met, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Deutschland GmbH Model MBB-BK 117 C-2 helicopters. The FAA previously sent this AD as an emergency AD to all known U.S. owners and operators of these helicopters. This AD was prompted by a report of vibrations of the yaw axis during a hover taxi. This AD requires repetitively inspecting the bolted joint between the cardan- pivot joint assembly and the tail rotor actuator piston rod and, depending on the results, taking corrective action. This AD also prohibits installing certain tail rotor actuators unless its requirements are met. These actions are specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.