Department of Transportation February 24, 2021 – Federal Register Recent Federal Regulation Documents

This action proposes to rename the established restricted areas R-2206 to R-2206A and establish six new restricted areas R-2206B, R-2206C, R-2206D, R-2206E, R-2206F, and R-2206G, over the Clear Air Force Station (Clear AFS) at Clear, AK. The United States Air Force (USAF) on behalf of the Missile Defense Agency (MDA) requested this action to protect aircraft from hazardous High-Intensity Radiated Field (HIRF) produced by the Long Range Discrimination Radar (LRDR) at Clear AFS. LRDR contributes to the MDA's mission of developing and deploying a layered Department of Defense (DoD) Ballistic Missile Defense System (BMDS) to defend the United States from ballistic missile attacks of all ranges in all phases of flight. The proposed restricted areas are necessary to protect aviation from the hazardous HIRF and segregate non-participating aircraft.

The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) CF6-80C2A1, CF6-80C2A2, CF6- 80C2A3, CF6-80C2A5, CF6-80C2A5F, CF6-80C2A8, CF6-80C2B1, CF6-80C2B1F, CF6-80C2B2, CF6-80C2B2F, CF6-80C2B4, CF6-80C2B4F, CF6-80C2B5F, CF6- 80C2B6, CF6-80C2B6F, CF6-80C2B6FA, CF6-80C2B7F, CF6-80C2B8F, and CF6- 80C2D1F model turbofan engines. This AD was prompted by reports of incidents that resulted in a significant fuel loss during flight and an in-flight shutdown (IFSD) of the engine. This AD requires initial and repetitive shim checks of the hydromechanical unit/main engine control (HMU/MEC) idler adapter on the accessory gearbox (AGB) assembly and, depending on the results of the shim check, possible replacement of the inserts on the HMU/MEC idler adapter. As a terminating action, this AD requires a protrusion check and a pull-out test, and the replacement of inserts on the HMU/MEC idler adapter that fail either test. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD- 500-1A11 airplanes. This proposed AD was prompted by reports of deficiencies in the primary flight control computer (PFCC) and remote electronics unit (REU) software. This proposed AD would require installation of a software update to correct deficiencies in the PFCC and REU software, as specified in a Transport Canada Civil Aviation (TCCA) AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-100-1A10 airplanes. This AD was prompted by reports of failure of a certain fire detection and extinguishing (FIREX) control unit. This AD requires replacing FIREX control units having a certain part number. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 727 series airplanes. This AD was prompted by a determination that excessive sealant coating on internal wing Structural Significant Items (SSIs) may not reveal cracks during inspections required by AD 98-11-03 R1. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate inspections that will give no less than the required damage tolerance rating (DTR) for certain SSIs of the wing. This AD also requires repetitive inspections for cracking of the affected SSIs and repair if necessary. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is revising an earlier proposal for certain The Boeing Company Model 767-200, -300, -300F, and -400ER series airplanes. This action revises the notice of proposed rulemaking (NPRM) by adding airplanes to the applicability and proposing to require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is proposing this airworthiness directive (AD) to address the unsafe condition on these products. Since these actions would impose an additional burden over that in the NPRM, the FAA is reopening the comment period to allow the public the chance to comment on these changes.

The FAA proposes to supersede Airworthiness Directive (AD) 2019-22-07, which applies to all MHI RJ Aviation ULC Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes, Model CL-600-2C10 (Regional Jet Series 700, 701 & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, Model CL-600-2D24 (Regional Jet Series 900) airplanes, and Model CL-600-2E25 (Regional Jet Series 1000) airplanes. AD 2019-22-07 requires revising the existing airplane flight manual (AFM) to include a limitation and an abnormal operating procedure for the Automatic Flight Control System (AFCS). Since the FAA issued AD 2019-22-07, it was found that the limitation and abnormal operating procedure did not include reference to a certain mode. This proposed AD would require revising the existing AFM and adding airplanes to the applicability. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-100-1A10 airplanes. This proposed AD was prompted by reports of DC motor pump (DCMP) failures during production flight tests. This proposed AD would require installing a redesigned DCMP electric motor assembly. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A319-171N airplanes, Model A320-271N, -272N, and -273N airplanes, and Model A321-271N, -272N, -271NX, and -272NX airplanes. This proposed AD was prompted by a report indicating that during a full scale fatigue test of the forward engine mounts, premature wear was identified on the forward engine mount shackle assemblies; in addition, during bearing replacement, the bearing lock washer was found broken. This proposed AD would require replacing any forward engine mount shackle assemblies having a certain part number with a serviceable part, and re-identifying the engine mount, or replacing any forward engine mount assemblies having a certain part number, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 7X airplanes and Model FALCON 2000EX airplanes. This proposed AD was prompted by a report that non-certified ANCRA seat tracks were installed on some airplanes and that those seat tracks might not sustain required loads during an emergency landing. This proposed AD would require replacement of certain ANCRA seat tracks with certified (Brownline) seat tracks, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for all Saab AB, Support and Services Model SAAB 2000 airplanes. This proposed AD was prompted by a report indicating that the left-hand main landing gear (MLG) collapsed after touchdown, causing severe damage to the airplane. This proposed AD would require modifying the MLG hydraulic transfer valve, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products.