Department of Transportation November 9, 2009 – Federal Register Recent Federal Regulation Documents

This action proposes to modify Class E airspace at Rawlins Municipal/Harvey Field, Rawlins, WY. Additional controlled airspace is necessary to accommodate aircraft using the Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedure (SIAP) at Rawlins Municipal/Harvey Field, Rawlins, WY. The FAA is proposing this action to enhance the safety and management of aircraft operations at Rawlins Municipal/Harvey Field, Rawlins, WY. This will also update the airport name from Rawlins Municipal Airport.

This action proposes to amend Class E airspace at Lima, OH. Additional controlled airspace is necessary to accommodate new Standard Instrument Approach Procedures (SIAPs) at Lima Allen County Airport, Lima, OH. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations for SIAPs at Lima Allen County Airport.

This document announces receipt by the National Highway Traffic Safety Administration (NHTSA) of a petition for a decision that 1994-1999 Bimota SB6 motorcycles that were not originally manufactured to comply with all applicable Federal motor vehicle safety standards (FMVSS) are eligible for importation into the United States because (1) they are substantially similar to vehicles that were originally manufactured for sale in the United States and that were certified by their manufacturer as complying with the safety standards, and (2) they are capable of being readily altered to conform to the standards.

Notice is hereby given of a meeting of the Rail Energy Transportation Advisory Committee (RETAC), pursuant to section 10(a)(2) of the Federal Advisory Committee Act, Public Law 92-463, as amended (5 U.S.C., App. 2).

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for all Boeing Model 767 airplanes. This AD requires repetitive replacement of the internal electrical feed-through connectors of the boost pumps of the main fuel tank. This AD results from a report of cracking in the epoxy potting compound on the internal feed-through connector of the fuel boost pump in the area of the soldered wire connector lugs. We are issuing this AD to prevent a hazardous electrical path from the dry side to the wet side of the fuel boost pump through a cracked feed- through connector, or between pins or a pin and the shell on one side of the feed-through connector, which could create an ignition source on the wet side of the fuel boost pump or cause a fire in the fuel pump enclosure and lead to subsequent explosion of the fuel tank.

We are adopting a new airworthiness directive (AD) to supersede AD 2006-24-11, which applies to certain Hawker Beechcraft Corporation (HBC) (Type Certificate previously held by Raytheon Aircraft Company) Models 1900, 1900C, and 1900D airplanes. AD 2006-24- 11 currently requires you to repetitively inspect the forward, vertical, and aft flanges of both the left and right wing rear spar lower caps for cracks, repair any cracks found, and report the inspection results to the manufacturer. Since we issued AD 2006-24-11, the manufacturer has developed a modification kit to install on the wing rear spar lower caps that will terminate the 200-hour repetitive inspection required in AD 2006-24-11. Consequently, this AD requires installing the new modification kits on the wing rear spar lower caps and terminates the repetitive inspections required in AD 2006-24-11 when the kits are installed. We are issuing this AD to prevent fatigue cracks in the wing rear spar lower caps, which could result in fatigue failure of the wing rear spar lower caps. A rear spar failure could result in complete wing failure and the wing separating from the airplane.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: