Department of Transportation 2007 – Federal Register Recent Federal Regulation Documents

This notice provides interested parties with the opportunity to comment on changes to the Federal Transit Administration's (FTA) National Transit Database (NTD) policy on strike adjustments. On March 12, 2007, FTA provided notice to NTD reporters that it was changing its policy on strikes, to permit transit agencies to request an adjustment to their NTD data that are used in the apportionment of Urbanized Area Formula Grants to offset the effect of strikes, retroactive to the 2005 Report Year. FTA invites the public to comment on this policy change.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA proposes to adopt a new airworthiness directive (AD) for certain McDonnell Douglas Model 717-200 airplanes. This proposed AD would require installing an additional support bracket for the gray water drain hose, replacing the screw of the support bracket with a new screw for the potable water supply hose, installing a spacer, doing a detailed inspection to detect interference or wear damage on hoses, lines and/or cables, and doing corrective actions if necessary. This proposed AD results from reports of interference between the potable water supply hose and/or gray water drain hose at the aft lavatories with the fuel line and/or power feeder cables of the auxiliary power unit (APU) located below the aft cabin floor. We are proposing this AD to prevent interference and chafing between the potable water supply hose and/or gray water hose with the fuel line and/or power feeder cables of the APU, which may cause arcing and sparking, and/or fuel leaking, and consequent fire or explosion.

The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain McDonnell Douglas Model DC-8-55, DC-8F-54, and DC-8F-55 airplanes; and Model DC-8-60, DC-8-70, DC-8-60F, and DC-8-70F series airplanes. The existing AD currently requires a one-time inspection for previous repairs of the aft fuselage skin panel at the longeron 28 skin splice; repetitive inspections for cracks of the same area; and related investigative and corrective actions. The existing AD also provides optional actions for extending the repetitive inspection intervals. This proposed AD would re-define and more clearly describe the optional actions for extending the repetitive inspection intervals. This proposed AD results from our determination that the inspections and actions described in the existing AD do not adequately address the unsafe condition. We are proposing this AD to detect and correct cracks in the aft fuselage skin at the longeron 28 skin splice, which could lead to loss of structural integrity of the aft fuselage, resulting in rapid decompression of the airplane.

On April 27, 2004, the FAA revised its policy regarding the co-location of antenna systems on existing structures previously studied by the FAA. Based on various additional comments from industry regarding the initial policy, the FAA finds that further modifications to this policy are necessary.

The Information Collection Request (ICR) entitled ``Hazardous Materials Public Sector Training and Planning Grants'' is being revised to implement a statutory provision authorizing PHMSA to request information from states concerning fees related to the transportation of hazardous materials. In addition, this ICR is being revised to include more detailed information from grantees to enable us to more accurately evaluate the effectiveness of the grant program in meeting emergency response planning and training needs. In compliance with the Paperwork Reduction Act of 1995, this notice announces that the ICR will be submitted to the Office of Management and Budget (OMB) for revision and extension.

This document proposes to amend NHTSA's regulations that prescribe fees authorized by 49 U.S.C. Sec. 30141 for various functions performed by the agency with respect to the importation of motor vehicles that do not conform to all applicable Federal motor vehicle safety and bumper standards. An importer must file with U.S. Customs and Border Protection (CBP) a Department of Transportation (DOT) conformance bond at the time that a nonconforming motor vehicle is offered for importation into the United States, or in lieu of such a bond, the importer may post cash deposits or obligations of the United States to ensure that the vehicle will be brought into conformance with all applicable standards within 120 days from the date of importation, or will be exported from, or abandoned to, the United States. To avoid the costs of a DOT conformance bond, some importers have sought to post cash deposits, which would relieve the importers of the bonding costs but cause the agency to expend considerable resources. To permit the government to recover these expenses, this amendment would establish a fee for the agency's processing of these cash deposits or obligations of the United States that are furnished in lieu of a DOT conformance bond.

The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 216: Aeronautical Systems Security.

The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 206: Aeronautical Information Services Data Link.

In accordance with the procedures governing the application for, and the processing of, special permits from the Department of Transportation's Hazardous Material Regulations (49 CFR part 107, subpart B), notice is hereby given that the Office of Hazardous Materials Safety has received the application described herein. This notice is abbreviated to expedite docketing and public notice. Because the sections affected, modes of transportation, and the nature of application have been shown in earlier Federal Register publications, they are not repeated here. Request of modifications of special permits (e.g. to provide for additional hazardous materials, packaging design changes, additional mode of transportation, etc.) are described in footnotes to the application number. Application numbers with the suffix ``M'' denote a modification request. These applications have been separated from the new applications for special permits to facilitate processing.

This document announces a reopening of the comment period for the above-referenced NPRM. The NPRM proposed the adoption of a new airworthiness directive for all Airbus Model A300, A310, and A300-600 series airplanes. That NPRM invites comments concerning the proposed requirements for revising the Emergency Procedures sections of the airplane flight manuals to advise the flightcrew of new procedures for emergency evacuation. This reopening of the comment period is necessary to provide additional opportunity for public comment on the proposed requirements of that NPRM.

This document announces a reopening of the comment period for the above-referenced NPRM. The NPRM proposed the adoption of a new airworthiness directive for all BAE Systems (Operations) Limited Model BAe 146 and Model Avro 146-RJ airplanes. That NPRM invites comments concerning the proposed requirements for repetitive detailed visual inspections for corrosion, pitted fasteners, or pillowing of the APU heat shield and surrounding skin and, if applicable, removal of the heat shield and repair. This reopening of the comment period is necessary to provide additional opportunity for public comment on the proposed requirements of that NPRM.

This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2007-19-53, which was sent previously to all known U.S. owners and operators of the specified Bell Helicopter Textron, Inc. (BHTI) model helicopters by individual letters. This AD requires replacing each affected tail rotor blade (blade) with an airworthy blade with a serial number not listed in the applicability of this AD. This AD is prompted by three incidents in which blade tip weights were slung from the blades during flight causing significant vibration. The actions specified by this AD are intended to prevent loss of a blade tip weight, loss of a blade, and subsequent loss of control of the helicopter.

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Model 525B airplanes. This AD requires you to incorporate electrical power relay circuit protection kit part number (P/N) SB525B-24-02. This AD results from both the need to protect aircraft wiring left unprotected in the original design and a report of a Model 525B airplane experiencing in-flight loss of numerous systems, tripped circuit breakers, and burned wiring adjacent to the power distribution panel. We are issuing this AD to correct an incorrect wiring installation and to provide short-circuit protection for all wiring from the aircraft power distribution system. This condition could result in burned wiring and loss of various aircraft electrical systems.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The Department of Transportation (DOT or Department) is seeking comment on whether it should adopt a rule to enhance airline passenger protections in the following seven ways: require carriers to adopt contingency plans for lengthy tarmac delays and incorporate them in their contracts of carriage, require carriers to respond to consumer problems, deem operating a chronically delayed flight to be unfair and deceptive, require carriers to publish delay data, require carriers to publish complaint data, require on-time performance reporting for international flights, and require carriers to audit their compliance with their customer service plans. We are proposing that most of these measures cover certificated or commuter air carriers that operate domestic scheduled passenger service using any aircraft with more than 30 passenger seats. We are proposing that one measure cover the largest U.S. and foreign carriers and that two other measures cover the largest U.S. carriers.

In accordance with the Paperwork Reduction Act of 1995 and its implementing regulations, the Federal Railroad Administration (FRA) hereby announces that it is seeking approval of the following information collection activities. Before submitting these information collection requirements for clearance by the Office of Management and Budget (OMB), FRA is soliciting public comment on specific aspects of the activities identified below.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Boeing Model 737-600, 737-700, 737-700C, 737-800, and 737- 900 series airplanes. This proposed AD would require an inspection of the vertical fin lugs, skin, and skin edges for discrepancies, an inspection of the flight control cables, fittings, and pulleys in section 48 for signs of corrosion, an inspection of the horizontal stabilizer jackscrew, ball nut, and gimbal pins for signs of corrosion, and corrective actions if necessary. This proposed AD results from reports indicating that moisture was found within the section 48 cavity. We are proposing this AD to ensure that the correct amount of sealant was applied around the vertical fin lugs, skin and the skin edges. Missing sealant could result in icing of the elevator cables, which could cause a system jam and corrosion of structural and flight control parts, resulting in reduced controllability of the airplane.

This document announces a reopening of the comment period for the above-referenced NPRM. The NPRM proposed the adoption of a new airworthiness directive for all ATR Model ATR42 and ATR72 airplanes. That NPRM invites comments concerning the proposed requirements for revising the Airworthiness Limitations Section of the Instructions for Continued Airworthiness to incorporate new limitations for fuel tank systems. This reopening of the comment period is necessary to provide additional opportunity for public comment on the proposed requirements of that NPRM.

The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Boeing Model 767-200, -300, and -300F series airplanes. The existing AD currently requires reworking the surface of the ground stud bracket of the left and right transformer rectifier units (TRUs) and the airplane structure mounting surface, and measuring the resistance from the bracket to the structure and the ground lugs to the bracket using a bonding meter. This proposed AD would revise the applicability of the existing AD to include additional airplanes and would also require, among other actions, installation of a new ground stud bracket using faying surface bonding. This proposed AD results from a report of loss of all direct current (DC) power generation during a flight, due to inadequate electrical ground path between the ground bracket of the TRUs/main battery charger (MBC) and the structure. We are proposing this AD to prevent depletion of the main battery while in flight, resulting from the loss of both TRUs and the MBC, and consequent loss of all DC power, which could impact the safe flight and landing of the airplane due to the loss of function or malfunction of essential/critical systems and displays in the cockpit.

In accordance with the Paperwork Reduction Act of 1995, this notice announces the Maritime Administration's (MARAD's) intention to request extension of approval (with modifications) for three years of a currently approved information collection.

The Federal Aviation Administration (FAA) is issuing this notice to advise the public of the approval of a Finding of No Significant Impact (FONSI) on an Environmental Assessment for proposed Federal actions at Greater Peoria Airport, Peoria, Illinois. The FONSI specifies that the proposed federal actions and local development projects are consistent with existing environmental policies and objectives as set forth in the National Environmental Policy Act of 1969 and will not significantly affect the quality of the environment. A description of the proposed Federal actions is : (a) To issue an environmental finding to allow approval of the Airport Layout Plan (ALP) for the development items listed below; (b) Approval of the Airport Layout Plan (ALP) for the development items listed below; and (c) Establish eligibility of the Greater Peoria Airport Authority to compete for Federal funding for the development projects depicted on the Airport Layout Plan. The specific item in the local airport development project is to acquire approximately 34 acres of land in fee simple title off the Runway 31 end. Copies of the environmental decision and the Short Form EA are available for public information review during regular business hours at the following locations: 1. Greater Peoria Regional Airport, 6100 West Everett McKinley Dirksen Parkway, Peoria, Illinois 61607. 2. Division of Aeronautics-Illinois Department of Transportation, One Langhorne Bond Drive, Capital Airport, Springfield, Illinois 62707. 3. Chicago Airports District Office, Room 320, Federal Aviation Administration, 2300 East Devon Avenue, Des Plaines, Illinois 60018.

We propose to adopt a new airworthiness directive (AD) for BHTC Model 430 helicopters. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The aviation authority of Canada, with which we have a bilateral agreement, states in the MCAI: