Federal Aviation Administration October 2021 – Federal Register Recent Federal Regulation Documents
Results 51 - 100 of 132
Proposed Establishment of United States Area Navigation (RNAV) Route T-308; Anvik, AK
This action proposes to establish United States Area Navigation (RNAV) route T-308 in the vicinity of Anvik, AK in support of a large and comprehensive T-route modernization project for the state of Alaska.
Airworthiness Directives; Airbus Helicopters
The FAA proposes to supersede Airworthiness Directive (AD) 2018-11-01, which applies to certain Airbus Helicopters Model AS332L2 and EC225LP helicopters. AD 2018-11-01 requires installing a cut-out for the left-hand (LH) and right-hand (RH) rail support junction profiles and repetitively inspecting splices, frame 5295, and related equipment for a crack. Since the FAA issued AD 2018-11-01, the manufacturer has developed a modification for in-service helicopters for replacing aluminum splices with steel splices on frame 5295. This proposed AD would retain the requirements of AD 2018-11-01 and require a modification for replacing aluminum splices with steel splices on frame 5295 if cracking is found. This proposed AD would also provide terminating action for the repetitive inspections. The FAA is proposing this AD to address the unsafe condition on these products.
Commercial Space Transportation Advisory Committee: Notice of Public Meeting
This notice announces a meeting of the Commercial Space Transportation Advisory Committee (COMSTAC).
Airworthiness Directives; Schempp-Hirth Flugzeugbau GmbH Gliders
The FAA proposes to adopt a new airworthiness directive (AD) for certain Schempp-Hirth Flugzeugbau GmbH Model Duo Discus and Duo Discus T gliders. This proposed AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as jerky extension of the air brakes at very high air speeds, including cases where the air brake blades interlock. This proposed AD would require replacing certain air brake end stop bushings, inspecting certain other air brake end stops, and repairing if necessary. The FAA is proposing this AD to address the unsafe condition on these products.
Proposed Establishment of United States Area Navigation (RNAV) Route T-366; Point Hope, AK
This action proposes to establish United States Area Navigation (RNAV) route T-366 in the vicinity of Point Hope, AK in support of a large and comprehensive T-route modernization project for the state of Alaska.
COVID-19 Related Relief Concerning Operations at Chicago O'Hare International Airport, John F. Kennedy International Airport, Los Angeles International Airport, Newark Liberty International Airport, New York LaGuardia Airport, Ronald Reagan Washington National Airport, and San Francisco International Airport for the Winter 2021/2022 Scheduling Season
The FAA has determined to extend through March 26, 2022, the Coronavirus (COVID-19)-related limited, conditional waiver of the minimum slot usage requirement at John F. Kennedy International Airport (JFK), New York LaGuardia Airport (LGA), and Ronald Reagan Washington National Airport (DCA) that the FAA has already made available through October 30, 2021, for international operations only. Similarly, the FAA has determined to extend through March 26, 2022, its COVID-19-related limited, conditional policy for prioritizing flights canceled at designated International Air Transport Association (IATA) Level 2 airports in the United States, for purposes of establishing a carrier's operational baseline in the next corresponding season, for international operations only. These IATA Level 2 airports include Chicago O'Hare International Airport (ORD), Newark Liberty International Airport (EWR), Los Angeles International Airport (LAX), and San Francisco International Airport (SFO). This relief is limited to slots and approved operating times used by any carrier for international operations only, through March 26, 2022, and will be subject to the same terms and conditions, with minor modifications, that the FAA has already applied to the relief that remains available through October 30, 2021.
Airworthiness Directives; Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain serial-numbered Leonardo S.p.a. Model AW119 MKII helicopters. This AD was prompted by the discovery that the passenger cabin windows (windows) on a batch of helicopters were improperly installed during production. This AD requires removing and reinstalling the windows. The FAA is issuing this AD to address the unsafe condition on these products.
Notice of Intent To Release Certain Properties From All Terms, Conditions, Reservations and Restrictions of a Quitclaim Deed Agreement Between Miami Dade Aviation Department and the Federal Aviation Administration for the Opa Locka Executive Airport, Opa Locka, FL
The FAA hereby provides notice of intent to release 20.327 acres at the Opa Locka Executive Airport, Opa Locka, FL from the conditions, reservations, and restrictions as contained in a Quitclaim Deed agreement between the FAA and the Miami Dade Aviation Department, dated November 16, 1961. The subject property is located at the southwest corner of NW 37 Avenue and NW 151 Street and on the east side of the airport. The parcel is currently designated as aeronautical property. The property will be released of its federal obligations given the land is no longer required by the Miami Dade Aviation Department as aeronautical-use. There would be a positive fiscal impact to the County as the conversion of the use of this acreage from aeronautical use to non-aeronautical use will yield more revenue to the County. As such, Foundry Meek IV LLC would pay a non-aeronautical use land rent rate of $0.86 per square foot, yielding approximately an additional $555,677 for a total of $838,390 in annual rent to the County, a 4X increase in revenue over the aeronautical rent.
Public Notice of Surplus Property Release; Spokane International Airport, Spokane, Washington
Under FAA regulations, notice is being given that the FAA is considering a request from the City of Spokane, Washington and the County of Spokane, Washington, to waive the surplus property requirements for approximately 20 acres of airport property located at Spokane International Airport, in Spokane, Washington. The subject property is located in the southeast section of the airport within the Airport Business Park. This release will allow the City and the County to sell 1 parcel of airport property to King Beverage and to construct a distribution facility and light industrial use. There will be proceeds generated from the proposed release of this property for capital improvements at the airport. The City and County will receive not less than fair market value for the property and the revenue generated from the sale will be used for airport purposes. It has been determined through study that the subject parcel will not be needed for aeronautical purposes.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-841 and A330-941 airplanes. This AD was prompted by a report of incorrect take-off computations for crosswinds above 20 knots. This AD requires amending the existing aircraft flight manual (AFM), as specified in a European Union Aviation Safety Agency (EASA), which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Notice of Release From Federal Surplus Property and Grant Assurance Obligations at Syracuse Hancock International Airport (SYR), Syracuse, New York
The FAA proposes to rule and invites public comment on the application for a release of approximately 8.80 acres of federally obligated airport property at Syracuse Hancock International Airport, Syracuse, New York, from both the Federal Surplus Property obligations contained in the March 21, 1977 Quitclaim Deed, and the Grant Assurance obligations. This acreage is composed of portions of three parcels that were transferred from the United States of America to the City of Syracuse under the provisions of the Federal Property and Administrative Services Act of 1949 and the Surplus Property Act of 1944. The release will allow the airport to enter into a long-term non- aeronautical lease to sanction commercial development. The proposed use of land after the release will be compatible with the airport and will not interfere with the airport or its operation.
Airworthiness Directives; Airbus Helicopters
The FAA is superseding Airworthiness Directive (AD) 2021-04- 15, which applied to all Airbus Helicopters Model AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters; and certain Model AS350B3 helicopters. AD 2021-04-15 required repetitive visual inspections of the right-hand side of the vertical fin spar for discrepancies (cracking), and corrective action if necessary. This AD retains the requirements of AD 2021-04-15, and requires repetitive cleaning and repetitive detailed inspections for cracking of the vertical fin spar and vertical fin upper attachments, and corrective action if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also expands the applicability to include additional Model AS350B3 helicopters. This AD was prompted by a report that, during an unscheduled post-flight inspection of the tail cone area, a crack was found in the spar of the upper part of the vertical fin and fractures were found in the two front attachment screws. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Leonardo S.p.a. Helicopters
The FAA is superseding emergency Airworthiness Directive (AD) 2018-23-52, which applied to all Leonardo S.p.a. Model AW169 and AW189 helicopters. AD 2018-23-52 required inspecting the nut, cotter pin, lock-wire, and hinge bracket connected to the tail rotor servo-actuator (TRA) feedback lever link, and each connection of the TRA feedback lever link, and repair if necessary. AD 2018-23-52 also required applying a paint stripe or torque seal on the nut and reporting certain information. This AD requires repetitive inspections of the TRA, repetitive inspections and checks of the tail rotor duplex bearings (TR DB), installation of an improved TRA and TR DB, repetitive installations and checks of thermal strips, replacement of the improved TR DB (life limit), and applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD was prompted by a report of an accident of a Model AW169 helicopter, which was observed to have lost yaw control prior to the accident and a determination that certain inspections and checks of the TR DB, installation of an improved TRA and TR DB, certain other actions, and applicable corrective actions are necessary to address the unsafe condition. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.a. Model AB139, AW139, AB412, and AB412 EP helicopters. This AD was prompted by failure of an Emergency Flotation System (EFS) float compartment to inflate during maintenance of the EFS. This AD requires inspecting certain EFSs and depending on the results, marking certain parts or removing certain parts from service, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited (type certificate previously held by Bell Helicopter Textron Canada Limited) Model 429 helicopters. This AD was prompted by reports of incorrectly staked spherical bearings in the directional control bellcrank assembly. This AD requires a one-time inspection of the lower surface of the spherical bearing in the directional control bellcrank assembly to determine if it is properly staked and, depending on the findings, applicable corrective actions. For certain helicopters, this AD also requires repetitive inspections and, depending on the findings, applicable corrective actions. This AD also provides a terminating action for the repetitive inspections. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.a. Model AB139 and AW139 helicopters. This AD was prompted by a report of several occurrences of a cracked main gearbox (MGB) spherical bearing lock nut (lock nut). This AD requires removing from service a certain part-numbered MGB lock nut that is installed on certain part-numbered MGBs and replacing it with newly designed MGB lock nut. This AD also prohibits installing any MGB with the affected MGB lock nut and prohibits installing any affected MGB lock nut on any helicopter. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airworthiness Directives; Airbus Helicopters and Airbus Helicopters Deutschland GmbH (AHD) Helicopters
The FAA is adopting a new airworthiness directive (AD) for Airbus Helicopters Model AS332C, AS332C1, AS332L, AS332L1, AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350D, AS355E, AS355F, AS355F1, AS355F2, AS355N, AS355NP, AS-365N2, AS 365 N3, EC120B, EC130B4, EC130T2, EC 155B, EC155B1, SA-365N, and SA-365N1 helicopters; and Airbus Helicopters Deutschland GmbH (AHD) Model EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, EC135T3, MBB-BK117 C-2, and MBB-BK117 D-2 helicopters. This AD was prompted by failure of an Emergency Flotation System (EFS) float compartment to inflate during maintenance of the EFS. This AD requires inspecting certain EFSs and depending on the results, marking certain parts or removing certain parts from service, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference (IBR). The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Helicopters
The FAA is adopting a new airworthiness directive (AD) for Airbus Helicopters Model AS355E, AS355F, AS355F1, and AS355F2 helicopters. This AD was prompted by multiple fatigue cracks in power turbine (PT) 3rd stage wheels. This AD requires revising the existing Rotorcraft Flight Manual (RFM) for your helicopter and installing a placard. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.a Model AW189 helicopters. This AD was prompted by a report of an incorrect connection of the inflation hoses to the tee manifolds of the inflation line on the emergency flotation system (EFS) assembly. This AD requires visually inspecting the yellow sleeves and hoses installed on each EFS assembly and depending on the inspection results, accomplishing the corrective actions in the applicable service information as specified in a European Aviation Safety Agency (now European Union Aviation Safety Agency) (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Sikorsky Aircraft Corporation Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Sikorsky Aircraft Corporation (Sikorsky) Model S-92A helicopters. This AD was prompted by an incident of a side facing utility seat detaching from wall attachment points. This AD requires modifying certain side facing utility seats and observer seats, and prohibits installing those seats unless the modification has been accomplished. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.a. Model AW169 helicopters. This AD was prompted by reports of in-flight pilot collective stick oscillation. This AD requires a one-time measurement of the friction of the pilot collective stick assembly to verify that it is within the allowable range and, depending on findings, making an adjustment to restore the acceptable level of friction, as specified in a European Aviation Safety Agency (now European Union Aviation Safety Agency) (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Pacific Aerospace Limited Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Pacific Aerospace Limited Model 750XL airplanes. This AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI identifies the unsafe condition as installation of the wing leading edge tank fuel pickup assembly in a pre-stressed condition, which could cause cracks in the wing spar web or the fuel pickup assembly pipe. This AD requires inspecting the angle of the support bracket on the wing leading edge tank fuel pickup assembly and taking any necessary corrective actions. The FAA is issuing this AD to address the unsafe condition on these products.
Proposed Establishment of Restricted Area R-2511; Trona, CA
This action proposes to establish restricted area R-2511 in the vicinity of Trona, CA in support of the Naval Air Warfare Center Weapons Division (NAWCWD) at China Lake, CA. The proposed restricted area is necessary to segregate the testing and evaluation of hazardous weapons systems, and other unproven aviation platforms in the early development cycle from non-participating aircraft.
Public Meeting/Notice of Availability for Proposed Air Tour Management Plan at Golden Gate National Recreation Area; Muir Woods National Monument; San Francisco Maritime National Historical Park; and Point Reyes National Seashore
The FAA, in cooperation with the National Park Service (NPS), has initiated development of a combined Air Tour Management Plan (ATMP) for the Golden Gate National Recreation Area, Muir Woods National Monument, San Francisco Maritime National Historical Park, and Point Reyes National Seashore (collectively referred to as the Parks) pursuant to the National Parks Air Tour Management Act of 2000 (the Act) and its implementing regulations. The Act requires that in developing an ATMP for a national park or tribal lands, the FAA and the NPS must hold at least one public meeting with interested parties. In addition, the Act requires that the ATMPs be published in the Federal Register for notice and comment and that copies be made available to the public. This notice announces the public availability of the proposed ATMP for comment and the public meeting for the Parks. The purpose of this meeting is to review the proposed ATMP and further ATMP development with the public. In accordance with Section 106 of the National Historic Preservation Act, the FAA and the NPS are also seeking public comment on the potential of the proposed ATMP to cause adverse effects to historic properties.
Petition for Exemption; Summary of Petition Received; The Boeing Company
This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Petition for Exemption; Summary of Petition Received; The Boeing Company
This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Women in Aviation Advisory Board; Notice of Public Meeting
This notice announces a meeting of the Women in Aviation Advisory Board (the Board).
Airworthiness Directives; Bombardier, Inc., Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-2B16 (604 Variant) airplanes. This AD was prompted by multiple reports of cracking of the main landing gear (MLG) shock strut lower pin. This AD requires repetitive lubrication and repetitive detailed visual inspections (DVI) and non- destructive test (NDT) inspections of the MLG shock strut lower pins, and replacement if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Dassault Aviation Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Dassault Aviation Model FALCON 7X, FALCON 900EX, and FALCON 2000EX airplanes. This AD was prompted by a report of a manufacturing issue involving misalignment of a cabin seat pin and plate that can prevent the recline locking mechanism from properly engaging when the seat is in taxi, take-off, or landing position. This AD requires an inspection of certain cabin seats for discrepancies and corrective action, as specified in European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is superseding Airworthiness Directive (AD) 2019-19- 06, which applied to certain Airbus SAS Model A330-202, -243, -243F, - 302, -323, and -343 airplanes. AD 2019-19-06 required an inspection to determine the part number and serial number of the slat geared rotary actuators (SGRAs), and replacement of each affected SGRA with a serviceable part. This AD continues to require replacement of each affected SGRA with a serviceable part, expands the applicability to include all airplanes on which the affected part may be installed, and also prohibits installation of an affected part; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD was prompted by a report that cracks have been found within the ring gears of the SGRAs due to a change in the manufacturing process and inadequate post-production non-destructive testing for potential cracking, and a determination that the requirements of AD 2019-19-06 may not ensure the permanent removal from service of affected SGRAs. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; De Havilland Aircraft of Canada Limited (Type Certificate Previously Held by Bombardier, Inc.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain De Havilland Aircraft of Canada Limited Model DHC-8-102, -103, and -106 airplanes; Model DHC-8-201 and -202 airplanes; Model DHC-8- 301, -311, and -315 airplanes; and Model DHC-8-400, -401, and -402 airplanes. This AD was prompted by reports that mounting nuts attaching the rudder actuator bracket to the vertical stabilizer have been found cracked or missing due to hydrogen embrittlement. This AD requires a one-time inspection of the rudder actuator bracket mounting nuts, and corrective actions if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Proposed Amendment of Class E Airspace; Covington, GA
This action proposes to amend Class E airspace extending upward from 700 feet above the surface for Covington Municipal Airport, Covington, GA. The FAA is proposing this action as a result of an airspace review caused by the decommissioning of the ALCOVY Non- directional Beacon (NDB) and cancellation of the associated approaches. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations in the area.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 747-400, -400D, and -400F series airplanes. This proposed AD was prompted by reports of burned Boeing Material Specification (BMS) 8-39 urethane foam, and a report from the airplane manufacturer that airplanes were assembled with seals throughout various areas of the airplane (including flight deck and cargo compartments) made of BMS 8-39 urethane foam, a material with fire-retardant properties that deteriorate with age. This proposed AD would require replacing the system tube/wire seals made of BMS 8-39 urethane foam in certain areas of the airplane. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to supersede Airworthiness Directive (AD) 2016-09-01, which applies to certain The Boeing Company Model 777-200 and -300 series airplanes. AD 2016-09-01 requires repetitive inspections for cracking of the left-and right-side forward outer chords of the pivot bulkhead, and related investigative and corrective actions if necessary. AD 2016-09-01 also provides a modification of the pivot bulkhead, which terminates the repetitive inspections. Since the FAA issued AD 2016-09-01, it has received reports that cracking of the left- and right-side forward outer chords of the pivot bulkhead were found at earlier compliance times than those specified in AD 2016-09-01 and determined that the inspection areas must be expanded, and that additional inspections are needed in areas that were modified as specified in AD 2016-09-01. This proposed AD would retain certain requirements of AD 2016-09-01. This proposed AD would require doing repetitive detailed and high frequency eddy current (HFEC) inspections of the longeron fitting and, for certain airplanes, the bulkhead assembly structure, for any cracking and doing all applicable on- condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A318, A319, A320, A321, A330-200, A330-200 Freighter, A330-300, A330-800, A330-900, A340-200, A340-300, A340-500, A340-600, and A380-800 series airplanes. This AD was prompted by a report that repetitive disconnection and reconnection of certain batteries during airplane parking or storage could lead to a reduction in capacity of those batteries. This AD requires replacing certain nickel-cadmium (Ni- Cd) batteries with serviceable Ni-Cd batteries, or maintaining the electrical storage capacity of those Ni-Cd batteries during airplane storage or parking, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide for the safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPS) and associated Takeoff Minimums and Obstacle Departure procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-700, -800, and -900ER series airplanes. This proposed AD was prompted by reports of incorrectly installed fuselage skin fasteners. This proposed AD would require a detailed inspection of a certain body station bulkhead, between certain stringers, for any incorrectly installed fastener common to fuselage skin, and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500- 1A11 airplanes. This AD was prompted by a report that following an in- service engine shutdown during taxi, water was found to be dripping into the forward avionics bay; the water caused a short circuit and tripped a circuit breaker. This AD requires replacing the forward galley slotted drain covers with solid blanking plates and modifying the associated drain tubing to block water. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by a report that during flight tests, the opening of the ram air outlet flaps was found to cause a disturbance of the air flow around the ram air turbine (RAT) when the landing gear (L/G) is extended. This AD requires revising the existing airplane flight manual (AFM) and applicable corresponding operational procedures to provide procedures for all engines failure and L/G gravity extension related to certain software, and installing Airbus temporary quick change (ATQC) V3 for the flight warning system (FWS) software (SW) standard (STD) 6/ 2.0, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Proposed Modification of Class D and Class E Airspace; China Lake NAWS (Armitage Field) Airport, CA
This action proposes to modify the Class D airspace at China Lake NAWS (Armitage Field) Airport, China Lake, CA. This action also proposes to modify the Class E airspace extending upward from 700 feet above the surface. Additionally, this action proposes to remove the China Lake (Navy) TACAN from the Class E5 text header and airspace description. Lastly, this action proposes numerous administrative updates to the Class D and Class E5 text headers and the Class D airspace description. This action would ensure the safety and management of instrument flight rules (IFR) operations at the airport.
Proposed Modification of Class E Airspace; Inyokern Airport, CA
This action proposes to modify the Class E airspace at Inyokern Airport, Inyokern, CA. This action also proposes two administrative updates to the Class E5 text header. This action would ensure the safety and management of instrument flight rules (IFR) operations at the airport.
Airworthiness Directives; Airbus Helicopters
The FAA proposes to supersede Airworthiness Directive (AD) 2020-11-05, which applies to all Airbus Helicopters Model EC120B helicopters. AD 2020-11-05 requires repetitive inspections of the tail rotor (TR) hub body for cracks and applicable corrective actions if necessary, and repetitive replacement of the attachment bolts, washers, and nuts of the TR hub body. This proposed AD would retain certain requirements of AD 2020-11-05, add repetitive inspections, require additional corrective actions, and update applicable service information. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Umlaut Engineering GmbH (Previously P3 Engineering GmbH) HAFEX (Halon-Free) Hand-Held Fire Extinguishers
The FAA proposes to adopt a new airworthiness directive (AD) for certain Umlaut Engineering GmbH (previously P3 Engineering GmbH) HAFEX (Halon-free) hand-held P3HAFEX fire extinguishers (fire extinguishers). This proposed AD was prompted by reports of a quality control issue on certain fire extinguishers, where the spindle geometries of the fire extinguishers were found to be out of tolerance. This proposed AD would require removing affected fire extinguishers from service. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Vulcanair S.p.A. Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Vulcanair S.p.A. Models P.68C, P.68C-TC, P.68 ``OBSERVER,'' P.68 OBSERVER 2, P.68R, and P.68TC OBSERVER airplanes. This proposed AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a damaged stabilator trim control cable. This proposed AD would require inspecting the stabilator trim control cables and replacing if necessary. This proposed AD would also require reporting the results of each inspection to Vulcanair S.p.A. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Pilatus Aircraft Ltd. Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Pilatus Aircraft Ltd. (Pilatus) Model PC-24 airplanes. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as insufficient performance of the fuel drain system that could lead to fire and damage of the airplane. This proposed AD would require modifying the fuel drain pipe routing and installing a drain mast. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Stemme AG Gliders
The FAA proposes to adopt a new airworthiness directive (AD) for certain Stemme AG Model Stemme S 12 gliders. This proposed AD was prompted by mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the incorrect installation of an axle connecting the main landing gear (MLG) to the center steel frame. This proposed AD would require inspecting the MLG installation. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; General Electric Company Turbofan Engines
The FAA proposes to adopt a new airworthiness directive (AD) for certain General Electric Company (GE) CF34-8C and CF34-8E model turbofan engines. This proposed AD was prompted by a report of a quality escape during the manufacturing of a high-pressure turbine (HPT) rotor stage 1 disk. This proposed AD would require removing the HPT rotor stage 1 disk from service and replacing the HPT rotor stage 1 disk with a part eligible for installation. The FAA is proposing this AD to the unsafe condition on these products.
Proposed Amendment to United States Area Navigation Route (RNAV) T-227; Fairbanks, AK
This action proposes to amend United Stated Area Navigation (RNAV) route T-227 in the vicinity of Fairbanks, AK in support of a large and comprehensive T-route modernization project for the state of Alaska.
Revocation of Class E Airspace; Creech Air Force Base Airport, NV
This action revokes the Class E airspace extending upward from 700 feet above the surface at Creech Air Force Base (AFB) Airport, Indian Springs, NV. This action also implements several administrative updates to the Class D legal description.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.