Department of Transportation – Federal Register Recent Federal Regulation Documents

Results 2,501 - 2,550 of 55,788
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Noise Certification Standards for Subsonic Jet Airplanes and Subsonic Transport Category Large Airplanes
Document Number: 2023-28897
Type: Notice
Date: 2024-01-03
Agency: Federal Aviation Administration, Department of Transportation
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on May 8, 2023.
IFR Altitudes; Miscellaneous Amendments
Document Number: 2023-28895
Type: Rule
Date: 2024-01-03
Agency: Federal Aviation Administration, Department of Transportation
This amendment adopts miscellaneous amendments to the required IFR (instrument flight rules) altitudes and changeover points for certain Federal airways, jet routes, or direct routes for which a minimum or maximum en route authorized IFR altitude is prescribed. This regulatory action is needed because of changes occurring in the National Airspace System. These changes are designed to provide for the safe and efficient use of the navigable airspace under instrument conditions in the affected areas.
Qualification of Drivers; Exemption Applications; Hearing
Document Number: 2023-28888
Type: Notice
Date: 2024-01-03
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA announces its decision to renew exemptions for 16 individuals from the hearing requirement in the Federal Motor Carrier Safety Regulations (FMCSRs) for interstate commercial motor vehicle (CMV) drivers. The exemptions enable these hard of hearing and deaf individuals to continue to operate CMVs in interstate commerce.
Qualification of Drivers; Exemption Applications; Epilepsy and Seizure Disorders
Document Number: 2023-28887
Type: Notice
Date: 2024-01-03
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA announces its decision to renew exemptions for three individuals from the requirement in the Federal Motor Carrier Safety Regulations (FMCSRs) that interstate commercial motor vehicle (CMV) drivers have ``no established medical history or clinical diagnosis of epilepsy or any other condition which is likely to cause loss of consciousness or any loss of ability to control a CMV.'' The exemptions enable these individuals who have had one or more seizures and are taking anti-seizure medication to continue to operate CMVs in interstate commerce.
Qualification of Drivers; Exemption Applications; Hearing
Document Number: 2023-28886
Type: Notice
Date: 2024-01-03
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA announces receipt of applications from 10 individuals for an exemption from the hearing requirement in the Federal Motor Carrier Safety Regulations (FMCSRs) to operate a commercial motor vehicle (CMV) in interstate commerce. If granted, the exemptions would enable these hard of hearing and deaf individuals to operate CMVs in interstate commerce.
Qualification of Drivers; Exemption Applications; Hearing
Document Number: 2023-28885
Type: Notice
Date: 2024-01-03
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
FMCSA announces its decision to exempt 10 individuals from the hearing requirement in the Federal Motor Carrier Safety Regulations (FMCSRs) to operate a commercial motor vehicle (CMV) in interstate commerce. The exemptions enable these hard of hearing and deaf individuals to operate CMVs in interstate commerce.
Airworthiness Directives; WACO Classic Aircraft Corporation Airplanes
Document Number: 2023-28877
Type: Rule
Date: 2024-01-03
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain WACO Classic Aircraft Corporation Model 2T-1A-2 airplanes. This AD was prompted by reports of multiple types of cracks at the leading edge former ribs and trailing edge former ribs in the upper wing center section. This AD requires installing maneuver restriction placards in the front and rear cockpits, inspecting the leading and trailing edge former ribs for cracking, replacing any cracked ribs, modifying the upper wing center section assembly, and removing the maneuver restriction placards after completing the modification. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Engines
Document Number: 2023-28861
Type: Rule
Date: 2024-01-03
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for all Rolls-Royce Deutschland Ltd & Co KG (RRD) Model Trent 1000-AE3, Trent 1000-CE3, Trent 1000-D3, Trent 1000-G3, Trent 1000-H3, Trent 1000-J3, Trent 1000-K3, Trent 1000-L3, Trent 1000-M3, Trent 1000-N3, Trent 1000- P3, Trent 1000-Q3, and Trent 1000-R3 engines. This AD is prompted by a determination that certain intervals for visual inspection of the intermediate-pressure stage 8 (IP8) and high-pressure stage 3 (HP3) air transfer tubes and front bearing housing IP8 air feed tubes need to be reduced. This AD requires initial and repetitive visual inspections of the IP8 and HP3 air transfer tubes and front bearing housing IP8 air feed tubes for cracking, damage, or air leakage wear, and replacement, if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference (IBR). The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2023-28855
Type: Rule
Date: 2024-01-03
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by a reported quality escapement where the seat track fitting nuts were under-torqued on some flight attendant seats in production. This AD requires re-torquing each free-standing attendant seat track fitting nut. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
Document Number: 2023-28854
Type: Rule
Date: 2024-01-03
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A318, A319, A321, A330-200, A330-200 Freighter, A330- 300, A330-800, A330-900, A340-200, and A340-300 series airplanes; Model A320-211, -212, -214, -216, -231, -232, -233, -251N, -252N, -253N, - 271N, -272N, and -273N airplanes; and Model A340-541 and A340-642 airplanes. This AD was prompted by a report that a production deficiency of some SafeLav gaseous oxygen container (SLGOC) batches was identified during production testing of newly manufactured oxygen containers. This AD requires replacing affected SLGOCs and prohibiting the installation of affected SLGOCs, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Dassault Aviation Airplanes
Document Number: 2023-28853
Type: Rule
Date: 2024-01-03
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding Airworthiness Directive (AD) 2023-04- 10, which applied to all Dassault Aviation Model MYSTERE-FALCON 900 airplanes. AD 2023-04-10 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD continues to require the actions in AD 2023-04- 10, and requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Saab AB, Support and Services (Formerly Known as Saab AB, Saab Aeronautics) Airplanes
Document Number: 2023-28852
Type: Rule
Date: 2024-01-03
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for all Saab AB, Support and Services Model SAAB 2000 airplanes. This AD was prompted by a review of the anti-skid system that revealed the possibility of inadvertently connecting the inboard harness to the outboard channel (and vice versa) of the wheel speed transducers in the main landing gear (MLG) wheel axles. This AD requires installing color markings on the harnesses and the wheel axles, to ensure proper installation and connection of the anti-skid harnesses, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
Document Number: 2023-28802
Type: Rule
Date: 2024-01-02
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding Airworthiness Directive (AD) 2022-08- 04, which applied to all Airbus SAS Model A300 series airplanes. AD 2022-08-04 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2022-08-04, the FAA has determined new or more restrictive airworthiness limitations are necessary. This AD continues to require the actions of AD 2022-08-04, and requires new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; MHI RJ Aviation ULC (Type Certificate Previously Held by Bombardier, Inc.) Airplanes
Document Number: 2023-28801
Type: Rule
Date: 2024-01-02
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain MHI RJ Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), CL-600-2C11 (Regional Jet Series 550), CL-600-2D15 (Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), and CL-600-2E25 (Regional Jet Series 1000) airplanes. This AD was prompted by a report of a passenger seat Y-belt (lap belt) re-installed in the wrong orientation, due to an incorrect maintenance manual. This AD requires inspecting certain Y-belts for correct installation and damage and corrective actions if necessary. This AD also prohibits the use of certain revisions of a maintenance task. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Bombardier, Inc., Airplanes
Document Number: 2023-28800
Type: Rule
Date: 2024-01-02
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by reports that the nose wheel steering selector valve (SSV) can be slow to deactivate under low temperature conditions. This AD requires replacing the affected SSV with a re-designed SSV that has an improved response time. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
Document Number: 2023-28799
Type: Rule
Date: 2024-01-02
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A310 airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Truck Leasing Task Force (TLTF); Notice of Public Meeting
Document Number: 2023-28794
Type: Notice
Date: 2024-01-02
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
This notice announces a meeting of the TLTF.
Airworthiness Criteria: Special Class Airworthiness Criteria for the Blackshape S.p.A., Model BK160-200 Very Light Airplane
Document Number: 2023-28718
Type: Proposed Rule
Date: 2024-01-02
Agency: Federal Aviation Administration, Department of Transportation
The FAA announces the availability of, and requests comments on, the proposed airworthiness criteria for the Blackshape S.p.A., Model BK160-200 Very Light Airplane (VLA). This document proposes the airworthiness criteria that the FAA finds to be appropriate and applicable for the VLA design.
Agency Request for Renewal of a Previously Approved Information Collection: Prioritization and Allocation Authority Exercised by the Secretary of Transportation Under the Defense Production Act
Document Number: 2023-28817
Type: Notice
Date: 2024-01-02
Agency: Department of Transportation
The Department of Transportation (DOT) invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The collection involves information required in an application to request Special Priorities Assistance. The information to be collected is necessary to facilitate the supply of civil transportation resources to promote the national defense. We are required to publish this notice in the Federal Register by the Paperwork Reduction Act of 1995, Public Law 104-13. A 60-day notice was published in the Federal Register on November 16, 2023. No comments were received.
Airworthiness Directives; Leonardo S.p.a. Helicopters
Document Number: 2023-28773
Type: Rule
Date: 2023-12-29
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for all Leonardo S.p.a. Model A109E, A109S, AW109SP, A119, and AW119 MKII helicopters. This AD was prompted by multiple reports of excessive axial play on the ball bearing of the lower half of the main rotor (MR) rotating scissor assembly. This AD requires one-time scissor coupling and axial play inspections and repetitive quantitative axial play inspections and, depending on the results, additional inspections and replacing certain parts. This AD also requires reporting information and prohibits installing certain parts unless certain inspections have been accomplished. These requirements are specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Transforming Transportation Advisory Committee; Public Meeting
Document Number: 2023-28771
Type: Notice
Date: 2023-12-29
Agency: Department of Transportation, Office of the Secretary
The Office of the Secretary of Transportation (OST) announces a public meeting of the Transforming Transportation Advisory Committee (TTAC) on Thursday, January 18, 2024. This notice announces the date, time, and location of the meeting, which will be virtually open to the public. The purpose of the TTAC is to provide information, advice, and recommendations to the Secretary on matters relating to transportation innovations.
Airworthiness Directives; Piaggio Aviation S.p.A. Airplanes
Document Number: 2023-28769
Type: Rule
Date: 2023-12-29
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Piaggio Aviation S.p.A. (Piaggio) Model P-180 airplanes. This AD is prompted by a report of corrosion on the various aluminum alloy reinforcements in the horizontal stabilizer (HS) central box caused by a humid environment inside the box from water ingress and/or condensation. This AD requires a one-time detailed inspection of the HS central box for corrosion; an assessment of the corrosion level; and depending on the determination, repetitive detailed inspections of the HS central box for corrosion and the internal composite structure for surface cracks, distortion, and damage; and repair or replacement of the HS assembly. Repair or replacement of the HS assembly is terminating action for the repetitive inspections. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Pilatus Aircraft Ltd. Airplanes
Document Number: 2023-28866
Type: Rule
Date: 2023-12-29
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Pilatus Aircraft Ltd. (Pilatus) Model PC-24 airplanes. This AD was prompted by a determination that the titanium threaded bolts at the forward end of the short rudder trim tab actuating rods could be subject to unexpectedly high oscillating loads due to aerodynamic forces acting on the rudder trim tab. This AD requires periodic replacement of affected titanium threaded bolts, a one-time inspection of the rudder mass balance arm and other elements of the rudder trim tab installation for correct attachment, damage (gouges), cracks, deformation, surface finish, and corrosion on any surrounding parts and, depending on findings, accomplishment of applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) emergency AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2023-28721
Type: Proposed Rule
Date: 2023-12-29
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model MD-11 and MD-11F airplanes equipped with General Electric (GE) CF6-80C2D1F high-bypass turbofan engines. This proposed AD was prompted by a report of a Model MD-11F airplane experiencing an uncommanded deployment of a thrust reverser in-flight at low altitude. This proposed AD would require a one-time detailed inspection of the engine pylon thrust reverser control system wire harnesses and applicable on-condition actions. The proposed AD would also require repetitive detailed inspections and wire integrity tests of the engine thrust reverser control system wire harnesses (in the pylon), junction box and junction box cover, left side and right side thrust reverser electrical harnesses, core (engine compartment) miscellaneous wire harness assembly, and 30 degree bulkhead wire harness assembly; and applicable on-condition actions. This AD also requires reporting. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; International Aero Engines, LLC Engines
Document Number: 2023-28703
Type: Proposed Rule
Date: 2023-12-28
Agency: Federal Aviation Administration, Department of Transportation
The FAA is withdrawing a notice of proposed rulemaking (NPRM) that proposed to supersede Airworthiness Directive (AD) 2022-19-15, which applies to certain International Aero Engines, LLC (IAE LLC) Model PW1100G series engines; and AD 2023-16-07, which applies to certain IAE LLC Model PW1100G series engines and PW1400G series engines. AD 2022-19-15 requires an angled ultrasonic inspection (AUSI) of the high-pressure turbine (HPT) 1st-stage disk and HPT 2nd-stage disk, and replacement if necessary. AD 2023-16-07 requires an AUSI of the HPT 1st-stage hub (also known as the HPT 1st-stage disk) and HPT 2nd-stage hub (also known as the HPT 2nd-stage disk) for cracks, and replacement if necessary, which is terminating action for AD 2022-19- 15. The NPRM was prompted by a manufacturer investigation that determined an increased risk of powder metal anomalies for all powder metal parts in certain powder metal production campaigns, which are susceptible to failure significantly earlier than previously determined. The NPRM would have retained the AUSI requirement for certain HPT 1st-stage and HPT 2nd-stage hubs from AD 2023-16-07. The NPRM would also have required performing an AUSI of the HPT 1st-stage hub, HPT 2nd-stage hub, high-pressure compressor (HPC) 7th-stage integrally bladed rotor (IBR-7), and HPC 8th-stage integrally bladed rotor (IBR-8) for cracks and replacement if necessary. The NPRM would also have required accelerated replacement of the HPC IBR-7, HPC IBR-8, HPC rear hub, HPT 1st-stage hub, HPT 1st-stage air seal, HPT 1st-stage blade retaining plate, HPT 2nd-stage hub, HPT 2nd-stage blade retaining plate, and HPT 2nd-stage rear seal. Since issuance of the NPRM, the FAA has received information that an error was inadvertently included in the compliance times for some of the HPT 1st-stage and 2nd-stage hubs, which would have required removal significantly later than necessary. Accordingly, the NPRM is withdrawn.
Airworthiness Directives; Airbus Helicopters
Document Number: 2023-28720
Type: Rule
Date: 2023-12-28
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding Airworthiness Directive (AD) 2022-27- 09, which applied to certain Airbus Helicopters Model EC130T2 helicopters. AD 2022-27-09 required repetitively inspecting the vibration level on the tail rotor drive shaft and, depending on the results, taking corrective action. AD 2022-27-09 also required reporting information and prohibited installing certain rotor drive shafts unless the inspection was done. Since the FAA issued AD 2022-27- 09, Airbus Helicopters revised its service information to update the procedures for inspecting that vibration level, reduce an allowable vibration level, and clarify when a balance correction may be accomplished. This AD was prompted by the determination that a certain vibration measurement tool was providing unexpected results and therefore the threshold must be revised. This AD continues to require certain actions in AD 2022-27-09 and also revises the procedures for inspecting the vibration level on the tail rotor drive shaft and depending on these results, requires replacing certain parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Macquarie Infrastructure Partners V GP, LLC-Control Exemption-Northern Indiana Railroad Company, LLC
Document Number: 2023-28716
Type: Notice
Date: 2023-12-28
Agency: Surface Transportation Board, Department of Transportation
Airworthiness Directives; International Aero Engines, LLC Engines
Document Number: 2023-28693
Type: Proposed Rule
Date: 2023-12-28
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to supersede Airworthiness Directive (AD) 2022-19-15, which applies to certain International Aero Engines, LLC (IAE LLC) Model PW1100G series engines; and AD 2023-16-07, which applies to certain IAE LLC Model PW1100G series engines and PW1400G series engines. AD 2022-19-15 requires an angled ultrasonic inspection (AUSI) of the high-pressure turbine (HPT) 1st-stage disk and HPT 2nd- stage disk, and replacement if necessary. AD 2023-16-07 requires an AUSI of the HPT 1st-stage hub (also known as the HPT 1st-stage disk) and HPT 2nd-stage hub (also known as the HPT 2nd-stage disk) for cracks, and replacement if necessary, which is terminating action for AD 2022-19-15. Since the FAA issued those two ADs, an investigation determined an increased risk of powder metal anomalies for all powder metal parts in certain powder metal production campaigns, which are susceptible to failure significantly earlier than previously determined. This proposed AD would retain the AUSI requirement for certain HPT 1st-stage and HPT 2nd-stage hubs from AD 2023-16-07. This proposed AD would also require performing an AUSI of the HPT 1st-stage hub, HPT 2nd-stage hub, high-pressure compressor (HPC) 7th-stage integrally bladed rotor (IBR-7), and HPC 8th-stage integrally bladed rotor (IBR-8) for cracks and replacement if necessary. This proposed AD would also require accelerated replacement of the HPC IBR-7, HPC IBR-8, HPC rear hub, HPT 1st-stage hub, HPT 1st-stage air seal, HPT 1st-stage blade retaining plate, HPT 2nd-stage hub, HPT 2nd-stage blade retaining plate, and HPT 2nd-stage rear seal. The FAA is proposing this AD to address the unsafe condition on these products.
Revisions to Civil Penalty Amounts, 2024
Document Number: 2023-28066
Type: Rule
Date: 2023-12-28
Agency: Federal Aviation Administration, Department of Transportation, Federal Motor Carrier Safety Administration, Federal Railroad Administration, Maritime Administration, National Highway Traffic Safety Administration, Pipeline and Hazardous Materials Safety Administration, Office of the Secretary
This final rule provides the statutorily prescribed 2024 adjustment to civil penalty amounts that may be imposed for violations of certain DOT regulations.
Airworthiness Directives; Bombardier, Inc., Airplanes
Document Number: 2023-28590
Type: Proposed Rule
Date: 2023-12-28
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-2B16 (601-3A, 601-3R, and 604 Variants) airplanes. This proposed AD was prompted by a report indicating that a new filter plate connector for the nose wheel steering (NWS) system electronic control module (ECM) does not meet certain certification requirements. This proposed AD would require replacing all affected non-compliant ECMs. This proposed AD would also prohibit the installation of affected parts under certain conditions. The FAA is proposing this AD to address the unsafe condition on these products.
Coastwise Endorsement Eligibility Determination for a Foreign-Built Vessel: White Lightning (Motor); Invitation for Public Comments
Document Number: 2023-28638
Type: Notice
Date: 2023-12-28
Agency: Maritime Administration, Department of Transportation
The Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to issue coastwise endorsement eligibility determinations for foreign-built vessels which will carry no more than twelve passengers for hire. A request for such a determination has been received by MARAD. By this notice, MARAD seeks comments from interested parties as to any effect this action may have on U.S. vessel builders or businesses in the U.S. that use U.S.-flag vessels. Information about the requestor's vessel, including a brief description of the proposed service, is listed below.
Coastwise Endorsement Eligibility Determination for a Foreign-Built Vessel: TACKLE BOX (Motor); Invitation for Public Comments
Document Number: 2023-28637
Type: Notice
Date: 2023-12-28
Agency: Maritime Administration, Department of Transportation
The Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to issue coastwise endorsement eligibility determinations for foreign-built vessels which will carry no more than twelve passengers for hire. A request for such a determination has been received by MARAD. By this notice, MARAD seeks comments from interested parties as to any effect this action may have on U.S. vessel builders or businesses in the U.S. that use U.S.-flag vessels. Information about the requestor's vessel, including a brief description of the proposed service, is listed below.
Coastwise Endorsement Eligibility Determination for a Foreign-Built Vessel: Ra (Motor); Invitation for Public Comments
Document Number: 2023-28636
Type: Notice
Date: 2023-12-28
Agency: Maritime Administration, Department of Transportation
The Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to issue coastwise endorsement eligibility determinations for foreign-built vessels which will carry no more than twelve passengers for hire. A request for such a determination has been received by MARAD. By this notice, MARAD seeks comments from interested parties as to any effect this action may have on U.S. vessel builders or businesses in the U.S. that use U.S.-flag vessels. Information about the requestor's vessel, including a brief description of the proposed service, is listed below.
Coastwise Endorsement Eligibility Determination for a Foreign-Built Vessel: OFF WATCH (Motor); Invitation for Public Comments
Document Number: 2023-28635
Type: Notice
Date: 2023-12-28
Agency: Maritime Administration, Department of Transportation
The Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to issue coastwise endorsement eligibility determinations for foreign-built vessels which will carry no more than twelve passengers for hire. A request for such a determination has been received by MARAD. By this notice, MARAD seeks comments from interested parties as to any effect this action may have on U.S. vessel builders or businesses in the U.S. that use U.S.-flag vessels. Information about the requestor's vessel, including a brief description of the proposed service, is listed below.
Coastwise Endorsement Eligibility Determination for a Foreign-Built Vessel: ODIN (Motor); Invitation for Public Comments
Document Number: 2023-28634
Type: Notice
Date: 2023-12-28
Agency: Maritime Administration, Department of Transportation
The Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to issue coastwise endorsement eligibility determinations for foreign-built vessels which will carry no more than twelve passengers for hire. A request for such a determination has been received by MARAD. By this notice, MARAD seeks comments from interested parties as to any effect this action may have on U.S. vessel builders or businesses in the U.S. that use U.S.-flag vessels. Information about the requestor's vessel, including a brief description of the proposed service, is listed below.
Coastwise Endorsement Eligibility Determination for a Foreign-Built Vessel: MIKHAYA (Sail); Invitation for Public Comments
Document Number: 2023-28633
Type: Notice
Date: 2023-12-28
Agency: Maritime Administration, Department of Transportation
The Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to issue coastwise endorsement eligibility determinations for foreign-built vessels which will carry no more than twelve passengers for hire. A request for such a determination has been received by MARAD. By this notice, MARAD seeks comments from interested parties as to any effect this action may have on U.S. vessel builders or businesses in the U.S. that use U.S.-flag vessels. Information about the requestor's vessel, including a brief description of the proposed service, is listed below.
Amendment of VOR Federal Airways V-48, V-52, V-216, and V-434, and Revocation of VOR Federal Airway V-206 in the Vicinity of Ottumwa, IA
Document Number: 2023-28381
Type: Proposed Rule
Date: 2023-12-27
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to amend Very High Frequency Omnidirectional Range (VOR) Federal Airways V-48, V-52, V-216, and V- 434, and revoke VOR Federal Airway V-206. The FAA is proposing this action due to the planned decommissioning of the VOR portion of the Ottumwa, IA (OTM), VOR/Distance Measuring Equipment (VOR/DME) navigational aid (NAVAID). The Ottumwa VOR is being decommissioned in support of the FAA's VOR Minimum Operational Network (MON) program.
Airworthiness Directives; Embraer S.A. (Type Certificate Previously Held by Yaborã Indústria Aeronáutica S.A.; Embraer S.A.) Airplanes
Document Number: 2023-28335
Type: Rule
Date: 2023-12-27
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for all Embraer S.A. Model ERJ 190-400 airplanes. This AD was prompted by a report of unexpected wear on the wing hinge bearing assembly of the aileron surfaces found during the functional test of the aileron control system backlash. This AD requires repetitive inspections of the press-fitted bushings of the wing ailerons for migration and broken sealant, measurements of the distance between the aileron surfaces and hinge fittings, functional checks of the backlash of the wing aileron control system, and all applicable related investigative and corrective actions, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Amendment of Class E Airspace; Statesboro, GA
Document Number: 2023-28312
Type: Rule
Date: 2023-12-27
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E airspace extending upward from 700 feet above the surface for Statesboro-Bulloch County Airport, Statesboro, GA, to support the revised area navigation (RNAV) instrument approach procedure. This action increases the radius of the Class E airspace extending upward from 700 feet above the surface, and updates the airport's name and geographic coordinates.
Airworthiness Directives; BAE Systems (Operations) Limited Airplanes
Document Number: 2023-28254
Type: Proposed Rule
Date: 2023-12-27
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to supersede Airworthiness Directive (AD) 2022-25-18, which applies to certain BAE Systems (Operations) Limited Model BAe 146 and Model Avro 146-RJ series airplanes. AD 2022-25-18 requires repetitive inspections for cracking of the main landing gear (MLG) side stay outer link and replacement if necessary. Since the FAA issued AD 2022-25-18, additional investigations of the causes of the cracking were conducted. This proposed AD would require a reduction of the repetitive visual inspection interval, provide optional repetitive special detailed inspections, accomplishing a one-off dimensional tolerance check and performing a repetitive lubrication of the MLG side stay outer link pivot, as specified in a United Kingdom (U.K.) Civil Aviation Authority (CAA) (U.K. CAA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Amendment of Class E Airspace; Thomasville, GA
Document Number: 2023-28406
Type: Rule
Date: 2023-12-27
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E airspace extending upward from 700 feet above the surface for Thomasville Regional Airport, Thomasville, GA. This action increases the existing radius, adds an extension to the northeast, and updates the airport's name.
Extension of the Prohibition Against Certain Flights in the Damascus Flight Information Region (FIR) (OSTT)
Document Number: 2023-28502
Type: Rule
Date: 2023-12-27
Agency: Federal Aviation Administration, Department of Transportation
This action extends the prohibition against certain flight operations in the Damascus Flight Information Region (FIR) (OSTT) by all: U.S. air carriers; U.S. commercial operators; persons exercising the privileges of an airman certificate issued by the FAA, except when such persons are operating U.S.-registered aircraft for a foreign air carrier; and operators of U.S.-registered civil aircraft, except when the operator of such aircraft is a foreign air carrier, for an additional five years, from December 30, 2023, until December 30, 2028. The FAA finds this action necessary to address significant safety-of- flight risks to U.S. civil aviation associated with the enduring complex conflict in Syria. The FAA also republishes the approval process and exemption information for this Special Federal Aviation Regulation (SFAR), consistent with other recently published flight prohibition SFARs.
Release of Waybill Data
Document Number: 2023-28568
Type: Notice
Date: 2023-12-27
Agency: Surface Transportation Board, Department of Transportation
Amendment of Jet Route J-211 and Revocation of VOR Federal Airway V-41; Youngstown, OH
Document Number: 2023-28513
Type: Proposed Rule
Date: 2023-12-27
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to amend Jet Route J-211 and to revoke Very High Frequency Omnidirectional Range (VOR) Federal Airway V-41. The FAA is proposing this action due to the planned decommissioning of the VOR portion of the Youngstown, OH (YNG), VOR/Tactical Air Navigation (VORTAC) navigational aid (NAVAID). The Youngstown VOR is being decommissioned in support of the FAA's VOR Minimum Operational Network (MON) program.
Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Engines
Document Number: 2023-28549
Type: Rule
Date: 2023-12-27
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding Airworthiness Directive (AD) 2021-25-04 for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) Model Trent 1000 engines. AD 2021-25-04 required operators to revise the airworthiness limitations section (ALS) of their existing approved continuous airworthiness maintenance program by incorporating the revised tasks of the applicable time limits manual (TLM) for each affected model turbofan engine. Since the FAA issued AD 2021-05-04, the manufacturer revised the TLM to introduce new or more restrictive tasks and limitations and associated thresholds and intervals for life-limited parts, which prompted this AD. This AD requires revising the ALS of the operator's existing approved engine maintenance or inspection program, as applicable, to incorporate new or more restrictive tasks and limitations and associated thresholds and intervals for life-limited parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Notice of Proposed Nonavailability Waiver of Buy America Requirements for the Nevada Department of Transportation To Purchase Certain High-Speed Rail Components
Document Number: 2023-28424
Type: Notice
Date: 2023-12-26
Agency: Federal Railroad Administration, Department of Transportation
The Federal Railroad Administration (FRA) is seeking comments on whether to grant a waiver of its Buy America requirements to the Nevada Department of Transportation (NVDOT) for certain components that are not produced in the United States for use in a high-speed passenger train project between Las Vegas, NV and Rancho Cucamonga, CA (Project). FRA selected the Project for funding under the Federal-State Partnership for Intercity Passenger Rail Program (FSP Program), and therefore, FRA's Buy America requirements apply to the Project. FRA's Buy America requirements include both FRA's statutory requirements, which require 100 percent of the manufactured products and steel and iron used in an FRA-funded project to be produced in the United States, and the Build America, Buy America Act (BABA), which requires that all construction materials used in the FRA-funded project be produced in the United States. FRA is not proposing to waive the applicable BABA requirements for construction materials used in the Project, and therefore this proposed waiver would not apply to the construction materials used in the Project. The proposed waiver would apply to the trainset, signal systems, high-speed rail turnout and fire alarm systems based on the domestic nonavailability of such components, as identified by NVDOT's railroad operating partner Brightline West and the two potential suppliers (Alstom and Siemens) of the rolling stock and signaling systems for the project. NVDOT and Brightline estimate that over 95 percent of the total direct dollar expenditures for the Project would be spent on domestically sourced products and labor, including 100 percent of the civil infrastructure costs.
Notice of Final Action of Waiver With Respect to Land; Coleman A. Young Municipal Airport, Detroit, MI
Document Number: 2023-28322
Type: Notice
Date: 2023-12-26
Agency: Federal Aviation Administration, Department of Transportation
The FAA is providing notice of a release of Federal obligations for one land parcel at Coleman A. Young Municipal Airport, Detroit, Michigan.
Agency Information Collection Activities: Notice of Request for Extension of Currently Approved Information Collection
Document Number: 2023-28321
Type: Notice
Date: 2023-12-26
Agency: Federal Highway Administration, Department of Transportation
The FHWA invites public comments about our intention to request the Office of Management and Budget's (OMB) approval for renewal of an existing information collection that is summarized below under SUPPLEMENTARY INFORMATION. We are required to publish this notice in the Federal Register by the Paperwork Reduction Act of 1995.
Agency Information Collection Activities: Notice of Request for Renewal of Currently Approved Information Collection
Document Number: 2023-28320
Type: Notice
Date: 2023-12-26
Agency: Federal Highway Administration, Department of Transportation
The FHWA has forwarded the information collection request described in this notice to the Office of Management and Budget (OMB) for approval of a renewal of information collection. We published a Federal Register Notice with a 60-day public comment period on this information collection on October 18, 2023. We are required to publish this notice in the Federal Register by the Paperwork Reduction Act of 1995.
Quarterly Rail Cost Adjustment Factor
Document Number: 2023-28318
Type: Notice
Date: 2023-12-26
Agency: Surface Transportation Board, Department of Transportation
The Surface Transportation Board has adopted the first quarter 2024 Rail Cost Adjustment Factor and cost index filed by the Association of American Railroads.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.