Federal Aviation Administration February 1, 2024 – Federal Register Recent Federal Regulation Documents
Results 1 - 11 of 11
Special Conditions: Gulfstream Aerospace Corporation Model GVIII-G700 and GVIII-G800 Series Airplanes; Dynamic Test Requirements for Single- and Multiple-Occupant Side-Facing Seats With or Without Airbag Systems
This action proposes special conditions for the Gulfstream Aerospace Corporation (Gulfstream) Model GVIII-G700 and GVIII-G800 series airplanes. These airplanes will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. This design feature is side-facing seats oriented in the aircraft with the occupant facing 90 degrees to the direction of aircraft travel. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Engines
The FAA proposes to adopt a new airworthiness directive (AD) for all Rolls-Royce Deutschland Ltd & Co KG (RRD) Model Trent 1000-A, Trent 1000-AE, Trent 1000-C, Trent 1000-CE, Trent 1000-D, Trent 1000-E, Trent 1000-G, and Trent 1000-H engines. This proposed AD was prompted by reports of cracking and separation of certain low-pressure turbine (LPT) stage 1 blade assemblies. This proposed AD would require initial and repetitive inspections of affected LPT stage 1 blade assemblies for cracking or separation and, depending on the results of the inspections, reduction of the inspection interval or replacement of the LPT stage 1 blade set and disk. This proposed AD would also prohibit the installation of an LPT disk or blade set assembly unless it is considered a serviceable part, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 777 airplanes. This AD was prompted by an evaluation by the design approval holder (DAH) that found the force limiter assemblies for the lateral control mechanism are not breaking out within the maximum design force requirements. This AD requires replacing affected force limiter assemblies and prohibits the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is superseding Airworthiness Directive (AD) 2020-26- 08, which applied to The Boeing Company Model 787-8, 787-9, and 787-10 airplanes powered by Rolls-Royce Trent 1000 engines. AD 2020-26-08 required repetitive inspections of the inner fixed structure (IFS) forward upper fire seal and thermal insulation blankets in the forward upper area of the thrust reverser (TR) for damage and applicable on- condition actions. Since the FAA issued AD 2020-26-08, the FAA determined that a new upper splitter fairing assembly is needed to prevent damage to the fire seal and thermal insulation blanket. This AD continues to require the actions specified in AD 2020-26-08 and requires determining if an affected part number of the upper splitter fairing assembly is installed on the engine, replacing an affected upper splitter fairing assembly part number with a new upper splitter fairing assembly part number, inspecting the IFS forward upper fire seal and thermal insulation blanket for any damage, and applicable on- condition actions. This AD also prohibits the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.
Amendment of Class E Airspace; Litchfield, MN
This action amends the Class E airspace at Litchfield, MN. This action is the result of an airspace review conducted due to the decommissioning of the Darwin very high frequency omnidirectional range (VOR) as part of the VOR Minimum Operating Network (MON) Program. This action brings the airspace into compliance with FAA orders to support instrument flight rule (IFR) operations.
Amendment of Class E Airspace; Harrison, OH
This action amends the Class E airspace at Harrison, OH. This action is the result of an airspace review conducted due to the decommissioning of the Cincinnati very high frequency omnidirectional range (VOR) as part of the VOR Minimum Operating Network (MON) Program. The geographic coordinates of the airport are also being updated to coincide with the FAA's aeronautical database. This action brings the airspace into compliance with FAA orders to support instrument flight rule (IFR) operations.
Airworthiness Directives; Britten-Norman Aircraft, Ltd. Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all Britten-Norman Aircraft, Ltd. Model BN-2, BN-2A, BN-2A-2, BN- 2A-3, BN-2A-6, BN-2A-8, BN-2A-9, BN-2A-20, BN-2A-21, BN-2A-26, BN-2A- 27, BN-2B-20, BN-2B-21, BN-2B-26, BN-2B27, BN-2T, BN2T-4R, and BN2T-4S airplanes; and Model BN2A MK. III, BN2A MK. III-2, and BN2A MK. III-3 airplanes. This proposed AD was prompted by reports of electrical cable (Koiled Kord) and flight control cables interference with the control column. This proposed AD would require inspecting for interference between the control column, rudder pedal adjuster cable, and any wiring (including the Koiled Kord) concurrently with performing a flight control full and free movement inspection, and taking corrective actions if necessary. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, 737-700, and 737-800 series airplanes. This AD was prompted by an evaluation by the design approval holder (DAH) indicating the fuselage skin repairs at the double row of fasteners centered on certain stringers have inadequate inspection requirements for continuing airworthiness following repair accomplishment. This AD is intended to complete certain programs to support the airplane reaching its limit of validity (LOV). This AD requires repetitive inspections for cracks of skin repairs at Stringer S-17, and corrective actions if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company (Boeing) Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by reports of undetected water leaks from the faucet control module (FCM) migrating below the passenger floor in multiple lavatory locations during flight, and into the electronic equipment bay(s). This AD requires repetitive general visual inspections of the area under all lavatory washbasins for evidence of intermittent and active leaks at the FCM and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is superseding Airworthiness Directive (AD) 2022-01- 07, which applied to certain Airbus SAS Model A350-941 and -1041 airplanes. AD 2022-01-07 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. This AD retains the actions required by AD 2022-01-07 and also requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300- 600 series airplanes). This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
