Federal Aviation Administration October 2014 – Federal Register Recent Federal Regulation Documents

These final special conditions are issued for the SNECMA, Silvercrest-2 SC-2D engine model. This engine will have a novel or unusual design featurean additional takeoff rating that increases the exhaust gas temperature (EGT) limit to maintain takeoff thrust in certain high ambient temperature conditions with one engine inoperative (OEI) for a maximum of 10 minutes. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These final special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

We are adopting a new airworthiness directive (AD) for all Rolls-Royce plc (RR) Trent 1000-A, 1000-C, 1000-D, 1000-E, 1000-G, and 1000-H turbofan engines. This AD requires removing engine electronic controller (EEC) software earlier than standard MB6.15 and replacing with a software standard eligible for installation. This AD was prompted by a finding that an intermediate pressure (IP) shaft failure may not be detected by EEC software earlier than standard MB6.15. We are issuing this AD to detect IP shaft failure and prevent IP compressor turbine burst, uncontained engine failure, and damage to the airplane.

The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 217Aeronautical Databases being held jointly with EUROCAE WG-44Aeronautical Databases.

We are superseding Airworthiness Directive (AD) 2005-14-07 for certain The Boeing Company Model 727, 727C, 727-100, 727-100C, 727-200, and 727-200F series airplanes. AD 2005-14-07 required repetitive inspections of the carriage attach fittings on the inboard and outboard foreflaps of each wing for cracking and other discrepancies, and corrective actions if necessary. This new AD requires reducing certain repetitive inspection intervals for the inboard and outboard carriage attach fittings for the outboard foreflaps, requires previously optional terminating actions which install improved outboard foreflap carriage attach fittings, and adds new initial and repetitive inspections of those fittings and corrective actions if necessary. This AD was prompted by a report of broken inboard and outboard carriage attach fittings of the outboard foreflaps found during an inspection. We are issuing this AD to detect and correct fatigue cracking of the attach fittings of the foreflap carriage of the wings, which could result in partial or complete loss of the foreflap and consequent loss of controllability of the airplane.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This action proposes to establish Class E airspace at Cando, ND. Controlled airspace is necessary to accommodate new Standard Instrument Approach Procedures (SIAPs) at Cando Municipal Airport. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations for SIAPs at the airport.

We are adopting a new airworthiness directive (AD) for certain Airbus Model A330-200 and -300 series airplanes, and Model A340-200 and -300 series airplanes. This AD was prompted by a report of contact between certain electrical harnesses and the hatrack rod that could cause chafing between the harnesses and surrounding structure. This AD requires modifying the routing of certain electrical harnesses. We are issuing this AD to prevent chafing and possible short circuit of two oxygen chemical generator containers in different wiring routes, which could result in malfunction of the electrical opening of all the containers connected to these routes. Such conditions, during a sudden depressurization event, could result in lack of oxygen and consequent injuries to airplane occupants.

We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D24 (Regional Jet Series 900) airplanes, and Model CL-600-2E25 (Regional Jet Series 1000) airplanes. This AD was prompted by a report that certain parts of the aft baggage door did not conform to the design specifications and were of degraded strength. This AD requires repetitive inspections for cracking and deformations of certain stop fittings and striker plates of the aft baggage bay door; and replacement, which would terminate the repetitive inspections. We are issuing this AD to prevent cracking and deformations of certain stop fittings and striker plates, which could result in the opening of the aft baggage bay door and rapid decompression or reduced controllability of the airplane.

We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B16 airplanes. This emergency AD was sent previously to all known U.S. owners and operators of these airplanes. This AD requires inspecting the inboard flap fasteners of the hinge-box forward fitting at Wing Station (WS) 76.50 and WS 127.25 to determine the orientation and condition of the fasteners, as applicable, and replacement or repetitive inspections of the fasteners if necessary. This AD also provides for optional terminating action for the requirements of the AD. This AD was prompted by reports of fractured fastener heads on the inboard flap hinge-box forward fitting at WS 76.50 due to incorrect installation. We are issuing this AD to detect and correct incorrectly oriented or fractured fasteners, which could result in premature failure of the fasteners attaching the inboard flap hinge-box forward fitting. Failure of the fasteners could lead to the detachment of the flap hinge box and the flap surface, and consequent loss of control of the airplane.

This amendment adopts miscellaneous amendments to the required IFR (instrument flight rules) altitudes and changeover points for certain Federal airways, jet routes, or direct routes for which a minimum or maximum en route authorized IFR altitude is prescribed. This regulatory action is needed because of changes occurring in the National Airspace System. These changes are designed to provide for the safe and efficient use of the navigable airspace under instrument conditions in the affected areas.

This rule amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

This rule amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

These special conditions are issued for the Boeing Model 767- 2C airplane. This airplane will have novel or unusual design features when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. These design features include the addition of four body fuel tanks and a modified fuel management system that, directly or as a result of failure or malfunction, could affect the airplane's structural performance. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for these design features. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

This document corrects two errors that appeared in Docket No. FAA-2014-0666, Special Conditions No. 25-566-SC, which was published in the Federal Register on September 12, 2014 (79 FR 54572). There is an error in the header information and in one instance of one of the airplane model numbers in the publication.

We propose to adopt a new airworthiness directive (AD) for certain Grob-Werke Models G115EG and G120A airplanes. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a defective starter solenoid. We are issuing this proposed AD to require actions to address the unsafe condition on these products.

This document announces the criteria, application procedures, and schedule to be applied by the Secretary of Transportation in designating or redesignating, and funding capital development for up to 15 current joint-use or former military airports seeking first time designation or redesignation to participate in the MAP.

The FAA is issuing this notice to advise the public of the third meeting of the 406 MHz Emergency Locator Transmitters (ELTs) Joint with EUROCAE WG-98 Committee.

We are adopting a new airworthiness directive (AD) for Pacific Aerospace Limited Model FU24-954 and FU24A-954 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracking of the control column at the wiring access hole, which could lead to loss of control. We are issuing this AD to require actions to address the unsafe condition on these products.

This document announces the availability of a proposed new chapter of FAA Order 8900.1, and a proposed new AC related to Aircraft Dispatcher Certification Courses. The new chapter in FAA Order 8900.1 chapter establishes Policy not previously addressed in FAA Orders or ACs. The associated AC, 65-XX, provides guidelines to operators and potential operators of Aircraft Dispatcher Certification Courses.

We propose to supersede Airworthiness Directive (AD) 2014-06- 08, for certain Bombardier, Inc. Model DHC-8-100, -200, and -300 series airplanes. AD 2014-06-08 currently requires repetitive functional checks of the nose and main landing gear, and corrective actions if necessary; and also provides optional terminating action modification for the repetitive functional checks. Since we issued AD 2014-06-08, we have determined that the optional terminating action modification is necessary to address the identified unsafe condition. This proposed AD would also require the terminating action modification. We are proposing this AD to detect and correct a false down-and-locked landing gear indication, which, on landing, could result in possible collapse of the landing gear.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.