Federal Aviation Administration March 2008 – Federal Register Recent Federal Regulation Documents
Results 101 - 150 of 174
Airworthiness Directives; Cessna Aircraft Company Model 525 Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Model 525 airplanes. This proposed AD would require you to inspect for missing firewall sealant between the aft firewall assembly and seal assembly; and, if you find that firewall sealant is missing, seal with firewall sealant between the aft firewall assembly and seal assembly. This proposed AD results from a report that firewall sealant may not have been applied between the aft firewall assembly and seal assembly during manufacture of certain Model 525 airplanes. We are proposing this AD to detect and correct missing firewall sealant between the aft firewall assembly and seal assembly, which could result in failure of the fire extinguishing system to prevent the spread of fire through the firewall gap. This failure could lead to an uncontrolled fire.
Airworthiness Directives; ATR Model ATR42-200, -300, -320, -500 Airplanes; and Model ATR72-101, -201, -102, -202, -211, -212, and -212A Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135BJ and EMB-145XR Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Sandel Avionics Incorporated Model ST3400 Terrain Awareness Warning System/Radio Magnetic Indicator (TAWS/RMI) Units Approved Under Technical Standard Order(s) C113, C151a, or C151b; Installed on Various Small and Transport Category Airplanes
The FAA proposes to revise an existing airworthiness directive (AD) that applies to Sandel Avionics Incorporated Model ST3400 TAWS/RMI units as described above. The existing AD currently requires installing a warning placard on the TAWS/RMI and revising the Limitations section of the airplane flight manual (AFM). The existing AD also requires installing upgraded software in the TAWS/RMI. This proposed AD would allow installing later revisions of the software described in the existing AD. This proposed AD results from a report that an in-flight bearing error occurred in a Model ST3400 TAWS/RMI configured to receive bearing information from a very high frequency omnidirectional range (VOR) receiver interface via a composite video signal, due to a combination of input signal fault and software error. We are proposing this AD to prevent a bearing error, which could lead to an airplane departing from its scheduled flight path, which could result in a reduction in separation from, and a possible collision with, other aircraft or terrain.
Airworthiness Directives; BAE Systems (Operations) Limited (Jetstream) Model 4101 Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Dassault Model Falcon 2000 Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Dornier Model 328-100 Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: During maintenance water has been found in the elevator assembly. The unsafe condition is water or ice accumulating in the elevator assembly, which could result in corrosion and consequent reduced structural integrity of the flight control surface, or an unbalanced flight control surface. These conditions could result in reduced controllability of the airplane. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-145, -145ER, -145MR, -145LR, -145XR, -145MP, and -145EP Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Boeing Model 757-200, -200PF, and -200CB Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 757-200, -200PF, and -200CB series airplanes. This AD requires doing an ultrasound inspection for disbonded tear straps not mechanically fastened to the skin, and related investigative and corrective actions, if necessary. This AD results from reports indicating that bonded skin panels may not have been correctly anodized in phosphoric acid before the tear strap doubler was bonded to the skin. We are issuing this AD to detect and correct a weak bond between the skin and tear strap. Such disbonding could reduce the ability of the skin to resist cracks and could adversely affect the structural integrity of the airplane.
Airworthiness Directives; Construcciones Aeronauticas, S.A. (CASA), Model C-212 Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Proposed Revocation of Area Navigation Jet Routes J-889R and J-996R; Alaska
The FAA is proposing to remove two Area Navigation (RNAV) Jet Routes designated as Jet Route J-888R and J-996R in Alaska. These routes transiting between Anchorage, and Bethel, AK, and Cape Newenham, and Anchorage, AK, respectively, are no longer required for routings provided by the Anchorage Air Route Traffic Control Center (ARTCC).
Airworthiness Directives; Cirrus Design Corporation Model SR20 Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Cirrus Design Corporation (CDC) Model SR20 airplanes. This proposed AD would require an inspection and replacement as necessary of the heat exchanger. This proposed AD results from the discovery of engine exhaust fumes in the cabin of CDC Model SR20 airplanes. We are proposing this AD to detect and correct leaks in the exhaust system, which could result in exhaust gases leaking into the cabin heating system. This condition could lead to carbon monoxide in the cabin and incapacitation of the pilot.
Airworthiness Directives; Lindstrand Balloons Ltd. Models 42A, 56A, 77A, 105A, 150A, 210A, 260A, 60A, 69A, 90A, 120A, 180A, 240A, and 310A Balloons
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Boeing Model 767 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 767 airplanes. This AD requires the following actions for the drive mechanism of the horizontal stabilizer: Repetitive detailed inspections for discrepancies and loose ball bearings; repetitive lubrication of the ballnut and ballscrew; repetitive measurements of the freeplay between the ballnut and the ballscrew; and corrective action if necessary. This AD also requires initial and repetitive inspections of the ballscrew-to-ballnut freeplay for certain airplanes. This AD results from a report of extensive corrosion of a ballscrew in the drive mechanism of the horizontal stabilizer on a similar airplane model. We are issuing this AD to prevent an undetected failure of the primary load path for the ballscrew in the drive mechanism of the horizontal stabilizer and subsequent wear and failure of the secondary load path, which could lead to loss of control of the horizontal stabilizer and consequent loss of control of the airplane.
Airworthiness Directives; Boeing Model 737-200 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 737-200 series airplanes. This AD requires repetitive inspections to detect cracking of the support fittings of the Krueger flap actuators, and corrective actions if necessary. This AD also requires eventual replacement of any existing aluminum support fitting on each wing with a steel fitting, and modification of the aft attachment of the actuator. Doing these actions terminates the repetitive inspection requirements. This AD results from reports of cracking due to fatigue and stress corrosion of the support fittings of the Krueger flap actuator. We are issuing this AD to prevent cracking of the support fittings, which could result in fracturing of the actuator attach lugs, separation of the actuator from the support fitting, severing of the hydraulic lines, resultant loss of hydraulic fluids, and consequent reduced controllability of the airplane.
Airworthiness Directives; BAE Systems (Operations) Limited Model BAe 146-100A, -200A, and -300A Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Airbus Model A330-200, A330-300, A340-200, and A340-300 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Airbus Model A330-200, A330-300, A340-200, and A340-300 series airplanes. That AD currently requires an accelerated schedule of repetitive testing of the elevator servo control loops, and corrective actions if necessary. This new AD retains the existing requirements, reduces the applicability of the existing AD, and adds terminating actions. This AD results from reports of failed elevator servo controls due to broken guides. We are issuing this AD to prevent failure of the elevator servo controls during certain phases of takeoff, which could result in an unannounced loss of elevator control and consequent reduced controllability of the airplane.
Airworthiness Directives; Saab Model SAAB SF340A and SAAB 340B (Including Variant 340B (WT)) Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; British Aerospace Regional Aircraft Model HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD requires repetitive detailed inspections for cracking of the left side and right side frame and reinforcement angles at fuselage station (FS) 640 between stringer 9 and stringer 12, and corrective actions if necessary. This AD also provides an optional terminating action for the repetitive inspections. This AD results from reports that cracks have been discovered on the frame and reinforcement angles at FS 640. We are issuing this AD to detect and correct cracking of the frame, which could lead to failure of the fuselage structure and possible loss of the airplane.
Airworthiness Directives; Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier Model CL-600-2C10 (Regional Jet Series 700, 701, & 702), Model CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; MD Helicopters, Inc. Model 600N Helicopters
This document supersedes an existing airworthiness directive (AD) for MD Helicopters, Inc. (MDHI) Model 600N helicopters. That AD currently requires interim initial and repetitive inspections of tailboom parts, installing six inspection holes in the aft fuselage skin panels, installing tailboom attachment bolt washers, modifying both access covers, and replacing broken attachment bolts. The current AD also provides for modifying the fuselage aft section as an optional terminating action. This amendment requires modifying the fuselage aft section within the next 24 months to strengthen the tailboom attachment fittings and upper longerons. The actions specified by this AD are intended to prevent failure of the tailboom attachment fittings, separation of the tailboom from the helicopter, and subsequent loss of control of the helicopter.
Airworthiness Directives; Airbus Model A330-200, A330-300, A340-200, and A340-300 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Airbus Model A330-200, A330-300, A340-200, and A340-300 series airplanes. That AD currently requires a revision of the airplane flight manual to include procedures for a pre-flight elevator check before each flight, repetitive inspections for cracks of the attachment lugs of the mode selector valve position transducers on the elevator servo controls, and corrective actions if necessary. This new AD retains the existing requirements, reduces the applicability of the existing AD, and adds terminating actions. For certain airplanes, this AD requires upgrading the flight control primary computers. This AD results from a report of cracks of the transducer body at its attachment lugs. We are issuing this AD to ensure proper functioning of the elevator surfaces, and to prevent cracking of the attachment lugs, which could result in partial loss of elevator function and consequent reduced controllability of the airplane.
Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800 and -900 Series Airplanes; and Model 757-200, -200PF, -200CB, and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing airplanes, identified above. This AD requires inspecting to determine if certain motor-operated shutoff valve actuators for the fuel tanks are installed, and related investigative and corrective actions if necessary. This AD also requires revising the Airworthiness Limitations (AWLs) section of the Instructions for Continued Airworthiness to incorporate AWL No. 28-AWL-21, No. 28-AWL-22, and No. 28-AWL-24 (for Model 737-600, -700, -700C, -800 and -900 series airplanes); and No. 28-AWL-23, No. 28-AWL-24, and No. 28-AWL-25 (for Model 757-200, -200PF, -200CB, and -300 series airplanes). This AD results from a design review of the fuel tank systems. We are issuing this AD to prevent electrical energy from lightning, hot shorts, or fault current from entering the fuel tank through the actuator shaft, which could result in fuel tank explosions and consequent loss of the airplane.
Airworthiness Directives; Airbus Model A300 and A300-600 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Eurocopter France Model EC130 B4 Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France Model EC130 B4 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The European Safety Agency (EASA), the Technical Agent for France, with which we have a bilateral agreement, states in the MCAI:
Airworthiness Directives; Eurocopter France Model EC130 B4 Helicopters
This amendment adopts a new airworthiness directive (AD) for Eurocopter France (ECF) Model EC130 B4 helicopters that requires, within 110 hours time-in-service (TIS), modifying and testing the wiring of the battery overheat sensing circuit. This amendment is prompted by a malfunction in the battery overheat sensing circuit found during a scheduled inspection. The actions specified by this AD are intended to correct the connection of the thermal switch to the cockpit indicator light, to notify the flight crew of an overheated battery, and to prevent a thermal runaway of the battery, an in-flight fire, and subsequent loss of control of the helicopter.
Airworthiness Directives; Fokker Model F27 Mark 050, 200, 300, 400, 500, 600, and 700 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Sierra Hotel Aero, Inc. Models Navion (L-17A), Navion A (L-17B), (L-17C), Navion B, Navion D, Navion E, Navion F, Navion G, and Navion H Airplanes
The FAA adopts a new airworthiness directive (AD) for all Sierra Hotel Aero, Inc. (formerly Navion Aircraft LLC) Models Navion (L-17A), Navion A (L-17B), (L-17C), Navion B, Navion D, Navion E, Navion F, Navion G, and Navion H airplanes. This AD requires you to do a one-time inspection of the entire fuel system and repetitive functional tests of certain fuel selector valves. This AD results from reports of airplane accidents associated with leaking or improperly operating fuel selector valves. We are issuing this AD to detect and correct fuel system leaks or improperly operating fuel selector valves, which could result in the disruption of fuel flow to the engine. This failure could lead to engine power loss.
Airworthiness Directives; Airbus Model A318, A319, A320, and A321 Airplanes
The FAA is superseding an existing AD that applies to certain Airbus Model A318, A319, A320, and A321 airplanes. That AD currently requires repetitive detailed inspections of the inboard flap trunnions for any wear marks and of the sliding panels for any cracking at the long edges, and corrective actions if necessary. This new AD adds airplanes that were recently added to the type certificate data sheet and changes the inspection type. This AD results from reports of wear damage to the inboard flap trunnions after incorporation of the terminating modification. We are issuing this AD to detect and correct wear of the inboard flap trunnions, which could lead to loss of flap surface control and consequently result in the flap detaching from the airplane. A detached flap could result in damage to the tail of the airplane.
Modification of Class E Airspace; Tucson, AZ
This action will modify Class E airspace at Tucson, AZ. Additional controlled airspace is necessary to encompass holding patterns and intermediate segments at Tucson International Airport. The FAA is proposing this action to enhance the safety and management of Instrument Flight Rules (IFR) operations at Tucson International Airport, Tucson, AZ.
Petition for Exemption; Summary of Petition Received
This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800, and -900 Series Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, -800, and -900 series airplanes. This proposed AD would require replacement of the power control relays in the P91 and P92 power distribution panels for the fuel boost and override pumps with new improved relays. This proposed AD would also require a revision to the Airworthiness Limitations (AWLs) section of the Instructions for Continued Airworthiness to incorporate AWL No. 28-AWL-20. This proposed AD results from fuel system reviews conducted by the manufacturer. We are proposing this AD to prevent pump housing burn-through due to electrical arcing, which could create a potential ignition source inside a fuel tank. This condition, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Airworthiness Directives; Bombardier Model DHC-8-102, DHC-8-103, DHC-8-106, DHC-8-201, DHC-8-202, DHC-8-301, DHC-8-311, and DHC-8-315 Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier Model DHC-8-400, DHC-8-401, and DHC-8-402 Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Bombardier Model CL-600-2B19 airplanes. The existing AD currently requires repetitive eddy current inspections for cracking of the main landing gear (MLG) main fittings, and replacement with new or serviceable MLG main fittings if necessary. The existing AD also currently requires servicing the MLG shock struts; inspecting the MLG shock struts for nitrogen pressure, visible chrome dimension, and oil leakage; and performing corrective actions, if necessary. This proposed AD would require replacement of the MLG main fittings with new improved MLG main fittings, which would terminate the repetitive inspections of the MLG main fittings and inspection and servicing of the MLG shock struts. This proposed AD results from premature failure of the MLG main fittings. We are proposing this AD to prevent failure of the MLG main fittings, which could result in collapse of the MLG upon landing.
Notice of Intent To Rule on Request To Release Airport Property at the Shafter-Minter Field Airport, Shafter, CA
The FAA proposes to rule and invite public comment on the release of land at the Shafter-Minter Field Airport under the provisions of section 125 of the Wendell H. Ford Aviation Investment Reform Act for the 21st Century (AIR 21).
RTCA Program Management Committee
The FAA is issuing this notice to advise the public of a meeting of the RTCA Program Management Committee.
Ninth Meeting: RTCA Special Committee 206/EUROCAE WG 76 Plenary
The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 206: Aeronautical Information Services Data Link.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This Rule establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Petition for Exemption; Summary of Petition Received
This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Airworthiness Directives; Bell Helicopter Textron Canada Models 206L, L-1, L-3, L-4, and 407 Helicopters
We propose to adopt a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) helicopters. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The Aviation Authority of Canada with whom we have a bilateral agreement states in the MCAI:
Airworthiness Directives; McDonnell Douglas Model DC-10-10 and DC-10-10F Airplanes, Model DC-10-15 Airplanes, Model DC-10-30 and DC-10-30F (KC-10A and KDC-10) Airplanes, Model DC-10-40 and DC-10-40F Airplanes, Model MD-10-10F and MD-10-30F Airplanes, and Model MD-11 and MD-11F Airplanes
We are revising an earlier proposed airworthiness directive (AD) for certain transport category airplanes identified above. The original NPRM would have required modifying the fuel boost pumps. The original NPRM resulted from a fuel boost pump found with blown thermal fuses and a fractured thrust washer. This action revises the original NPRM by referring to new service information, which would require more work. We are proposing this supplemental NPRM to prevent failure of the fuel boost pumps, which could lead to the potential of ignition sources inside fuel tanks. This condition, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
Airworthiness Directives; Agusta S.p.A. Model AB 139 and AW 139 Helicopters
We propose to adopt a new airworthiness directive (AD) for Agusta S.p.A. Model AB 139 and AW 139 helicopters. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The European Aviation Safety Agency (EASA), the Technical Agent for Italy, with which we have a bilateral agreement, states in the MCAI:
Revisions to Cockpit Voice Recorder and Digital Flight Data Recorder Regulations
This final rule amends cockpit voice recorder (CVR) and digital flight data recorder (DFDR) regulations affecting certain air carriers, operators, and aircraft manufacturers. This final rule increases the duration of certain CVR recordings, increases the data recording rate for certain DFDR parameters, requires physical separation of the DFDR and CVR, improves the reliability of the power supplies to both the CVR and DFDR, and requires that certain datalink communications received on an aircraft be recorded if datalink communication equipment is installed. This final rule is based on recommendations issued by the National Transportation Safety Board following its investigations of several accidents and incidents, and includes other revisions the FAA has determined are necessary. These changes to CVR and DFDR systems are intended to improve the quality and quantity of information recorded, and increase the potential for retaining important information needed for accident and incident investigations.
Airworthiness Directives; Saab Model SAAB-Fairchild SF340A (SAAB/SF340A) and SAAB 340B Airplanes
We are revising an earlier NPRM for the products listed above. This action revises the earlier NPRM by expanding the scope. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Modification of Class E Airspace; Hollister, CA
This action will amend Class E airspace at Hollister, CA. Additional controlled airspace is necessary to accommodate aircraft using a new Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedure (SIAP) at Hollister Municipal Airport, Hollister, CA. This will improve the safety of Instrument Flight Rules (IFR) aircraft executing the new RNAV GPS SIAP at Hollister Municipal Airport, Hollister, CA.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
