Airworthiness Directives; Bombardier Model DHC-8-102, DHC-8-103, DHC-8-106, DHC-8-201, DHC-8-202, DHC-8-301, DHC-8-311, and DHC-8-315 Airplanes, 12912-12915 [E8-4772]

Download as PDF 12912 Federal Register / Vol. 73, No. 48 / Tuesday, March 11, 2008 / Proposed Rules Authority for This Rulemaking § 39.13 Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. 2. The FAA amends § 39.13 by adding the following new AD: [Amended] Boeing: Docket No. FAA–2008–0269; Directorate Identifier 2007–NM–320–AD. Comments Due Date (a) We must receive comments by April 25, 2008. Affected ADs (b) None. Applicability (c) This AD applies to Boeing Model 737– 600, –700, –700C, –800, and –900 series airplanes, certificated in any category; as identified in Boeing Alert Service Bulletin 737–28A1201, dated February 19, 2007. Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866, 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. You can find our regulatory evaluation and the estimated costs of compliance in the AD Docket. Note 1: This AD requires revisions to certain operator maintenance documents to include new inspections. Compliance with these inspections is required by 14 CFR 91.403(c). For airplanes that have been previously modified, altered, or repaired in the areas addressed by these inspections, the operator may not be able to accomplish the inspections described in the revisions. In this situation, to comply with 14 CFR 91.403(c), the operator must request approval for an alternative method of compliance (AMOC) according to paragraph (i) of this AD. The request should include a description of changes to the required inspections that will ensure the continued operational safety of the airplane. Unsafe Condition (d) This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent pump housing burn-through due to electrical arcing, which could create a potential ignition source inside a fuel tank. This condition, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Safety. The Proposed Amendment sroberts on PROD1PC70 with PROPOSALS Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. VerDate Aug<31>2005 17:20 Mar 10, 2008 Jkt 214001 Compliance (e) Comply with this AD within the compliance times specified, unless already done. Replacement (f) Within 60 months after the effective date of this AD, replace the power control relays in the P91 and P92 power distribution panels for the fuel boost and override pumps with new improved relays having a ground fault interrupter (GFI) feature, in accordance with the Accomplishment Instructions of the service bulletin. Note 2: The Boeing service bulletin refers to Honeywell Service Bulletin 1151932–24– 61 and Honeywell Service Bulletin 1151934– 24–62, both dated November 10, 2006, as additional sources of service information for replacement of the power control relays in the P91 and P92 power distribution panels. Airworthiness Limitations (AWLs) Revision (g) Concurrently with accomplishing the actions specified in paragraph (f) of this AD, revise the AWLs section of the Instructions PO 00000 Frm 00012 Fmt 4702 Sfmt 4702 for Continued Airworthiness by incorporating AWL No. 28–AWL–20 of Subsection F of the Boeing 737–600/700/800/ 900 Maintenance Planning Data (MPD) Document, D626A001–CMR, Section 9, Revision March 2007 R2 (hereafter referred to as ‘‘the MPD’’). No Alternative Inspections or Inspection Intervals (h) After accomplishing the action specified in paragraph (g) of this AD, no alternative inspections or inspection intervals may be used unless the inspections or intervals are part of a later revision of the MPD that is approved by the Manager, Seattle ACO; or unless the inspections or intervals are approved as an AMOC in accordance with the procedures specified in paragraph (j) of this AD. Alternative Methods of Compliance (AMOCs) (i)(1) The Manager, Seattle ACO, FAA, ATTN: Jen Pei, Aerospace Engineer, Systems and Equipment Branch, ANM–130S, 1601 Lind Avenue, SW., Renton, Washington 98057–3356; telephone (425) 917–6409; fax (425) 917–6590; has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. (2) To request a different method of compliance or a different compliance time for this AD, follow the procedures in 14 CFR 39.19. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. Issued in Renton, Washington, on March 3, 2008. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E8–4773 Filed 3–10–08; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2008–0266; Directorate Identifier 2008–NM–013–AD] RIN 2120–AA64 Airworthiness Directives; Bombardier Model DHC–8–102, DHC–8–103, DHC– 8–106, DHC–8–201, DHC–8–202, DHC– 8–301, DHC–8–311, and DHC–8–315 Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: SUMMARY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed E:\FR\FM\11MRP1.SGM 11MRP1 Federal Register / Vol. 73, No. 48 / Tuesday, March 11, 2008 / Proposed Rules AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: Bombardier Aerospace has completed a system safety review of the aircraft fuel system against fuel tank safety standards introduced in Chapter 525 of the Airworthiness Manual through Notice of Proposed Amendment (NPA) 2002–043. The identified non-compliances were then assessed using Transport Canada Policy Letter No. 525–001, to determine if mandatory corrective action is required. The assessment showed that it is necessary to introduce Critical Design Configuration Control Limitations (CDCCL), in order to preserve critical fuel tank system ignition source prevention features during configuration changes such as modifications and repairs, or during maintenance actions. Failure to preserve critical fuel tank system ignition source prevention features could result in a fuel tank explosion. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI. DATES: We must receive comments on this proposed AD by April 10, 2008. ADDRESSES: You may send comments by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: (202) 493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue, SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–40, 1200 New Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. sroberts on PROD1PC70 with PROPOSALS Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Mazdak Hobbi, Aerospace Engineer, Airframe and Propulsion Branch, ANE– VerDate Aug<31>2005 17:20 Mar 10, 2008 Jkt 214001 171, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone (516) 228–7330; fax (516) 794–5531. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2008–0266; Directorate Identifier 2008–NM–013–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued Canadian Airworthiness Directive CF–2008–03, dated January 3, 2008 (referred to after this as ‘‘the MCAI’’), to correct an unsafe condition for the specified products. The MCAI states: Bombardier Aerospace has completed a system safety review of the aircraft fuel system against fuel tank safety standards introduced in Chapter 525 of the Airworthiness Manual through Notice of Proposed Amendment (NPA) 2002–043. The identified non-compliances were then assessed using Transport Canada Policy Letter No. 525–001, to determine if mandatory corrective action is required. The assessment showed that it is necessary to introduce Critical Design Configuration Control Limitations (CDCCL), in order to preserve critical fuel tank system ignition source prevention features during configuration changes such as modifications and repairs, or during maintenance actions. Failure to preserve critical fuel tank system ignition source prevention features could result in a fuel tank explosion. Revisions have been made to Part 2 ‘‘Airworthiness Limitations List’’ of the Maintenance Program Manuals of the affected models to introduce the required CDCCL. The corrective action is revising the Airworthiness Limitations Section of the Instructions for Continued Airworthiness to include the CDCCL data. You may obtain further information by examining the MCAI in the AD docket. PO 00000 Frm 00013 Fmt 4702 Sfmt 4702 12913 The FAA has examined the underlying safety issues involved in fuel tank explosions on several large transport airplanes, including the adequacy of existing regulations, the service history of airplanes subject to those regulations, and existing maintenance practices for fuel tank systems. As a result of those findings, we issued a regulation titled ‘‘Transport Airplane Fuel Tank System Design Review, Flammability Reduction and Maintenance and Inspection Requirements’’ (66 FR 23086, May 7, 2001). In addition to new airworthiness standards for transport airplanes and new maintenance requirements, this rule included Special Federal Aviation Regulation No. 88 (‘‘SFAR 88,’’ Amendment 21–78, and subsequent Amendments 21–82 and 21–83). Among other actions, SFAR 88 requires certain type design (i.e., type certificate (TC) and supplemental type certificate (STC)) holders to substantiate that their fuel tank systems can prevent ignition sources in the fuel tanks. This requirement applies to type design holders for large turbine-powered transport airplanes and for subsequent modifications to those airplanes. It requires them to perform design reviews and to develop design changes and maintenance procedures if their designs do not meet the new fuel tank safety standards. As explained in the preamble to the rule, we intended to adopt airworthiness directives to mandate any changes found necessary to address unsafe conditions identified as a result of these reviews. In evaluating these design reviews, we have established four criteria intended to define the unsafe conditions associated with fuel tank systems that require corrective actions. The percentage of operating time during which fuel tanks are exposed to flammable conditions is one of these criteria. The other three criteria address the failure types under evaluation: single failures, single failures in combination with a latent condition(s), and in-service failure experience. For all four criteria, the evaluations included consideration of previous actions taken that may mitigate the need for further action. We have determined that the actions identified in this AD are necessary to reduce the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane. Relevant Service Information Bombardier has issued de Havilland temporary revisions (TRs) to Part 2 E:\FR\FM\11MRP1.SGM 11MRP1 12914 Federal Register / Vol. 73, No. 48 / Tuesday, March 11, 2008 / Proposed Rules ‘‘Airworthiness Limitations List’’ (AWL) of the de Havilland Dash 8 Series Maintenance Program Manuals (MPMs). The TRs are listed in the following table titled ‘‘TRs to the DHC–8 MPMs.’’ TRS TO THE DHC–8 MPMS de Havilland TR TR date AWL–98 ..................... AWL 2–35 .................. AWL 3–103 ................ April 12, 2006 ....................................... April 12, 2006 ....................................... April 12, 2006 ....................................... The actions described in this service information are intended to correct the unsafe condition identified in the MCAI. FAA’s Determination and Requirements of This Proposed AD This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design. This proposed AD would allow revising the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness in accordance with later revisions of the MPM as an acceptable method of compliance if the CDCCL is part of a later approved MPM revision, or if the CDCCL is approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (g)(1) of this proposed AD. In most ADs, we adopt a compliance time allowing a specified amount of time after the AD’s effective date. In this case, however, the FAA has already issued regulations that require operators to revise their maintenance/inspection programs to address fuel tank safety issues. The compliance date for these regulations is December 16, 2008. To provide for coordinated implementation of these regulations and this proposed AD, we are using this same compliance date in this proposed AD. sroberts on PROD1PC70 with PROPOSALS Differences Between This AD and the MCAI or Service Information We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making VerDate Aug<31>2005 17:20 Mar 10, 2008 Jkt 214001 de Havilland MPM Dash 8 Series 100 MPM, Product Support Manual (PSM) 1–8–7. Dash 8 Series 200 MPM, PSM 1–82–7. Dash 8 Series 300 MPM, PSM 1–83–7. these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information. We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the proposed AD. Costs of Compliance Based on the service information, we estimate that this proposed AD would affect about 118 products of U.S. registry. We also estimate that it would take about 1 work-hour per product to comply with the basic requirements of this proposed AD. The average labor rate is $80 per work-hour. Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $9,440, or $80 per product. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national PO 00000 Frm 00014 Fmt 4702 Sfmt 4702 Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new AD: Bombardier, Inc. (Formerly de Havilland, Inc.): Docket No. FAA–2008–0266; Directorate Identifier 2008–NM–013–AD. Comments Due Date (a) We must receive comments by April 10, 2008. Affected ADs (b) None. Applicability (c) This AD applies to all Bombardier Model DHC–8–102, DHC–8–103, DHC–8– 106, DHC–8–201, DHC–8–202, DHC–8–301, DHC–8–311, and DHC–8–315 airplanes, certificated in any category, all serial numbers. E:\FR\FM\11MRP1.SGM 11MRP1 Federal Register / Vol. 73, No. 48 / Tuesday, March 11, 2008 / Proposed Rules Subject (d) Air Transport Association (ATA) of America Code 28: Fuel. The assessment showed that it is necessary to introduce Critical Design Configuration Control Limitations (CDCCL), in order to preserve critical fuel tank system ignition source prevention features during configuration changes such as modifications and repairs, or during maintenance actions. Failure to preserve critical fuel tank system ignition source prevention features could result in a fuel tank explosion. Revisions have been made to Part 2 ‘‘Airworthiness Limitations List’’ of the Maintenance Program Manuals of the affected models to introduce the required CDCCL. Reason (e) The mandatory continuing airworthiness information (MCAI) states: Bombardier Aerospace has completed a system safety review of the aircraft fuel system against fuel tank safety standards introduced in Chapter 525 of the Airworthiness Manual through Notice of Proposed Amendment (NPA) 2002–043. The identified non-compliances were then assessed using Transport Canada Policy Letter No. 525–001, to determine if mandatory corrective action is required. 12915 Instructions for Continued Airworthiness to include the CDCCL data. Actions and Compliance (f) Unless already done, do the following actions. (1) For all airplanes: Within 60 days after the effective date of this AD, or before December 16, 2008, whichever occurs first, revise the Airworthiness Limitations section of the Instructions for Continued Airworthiness to incorporate the CDCCL data specified in the applicable temporary revision (TR) to the applicable maintenance program manual (MPM). The TRs are listed in Table 1 of this AD. The corrective action is revising the Airworthiness Limitations Section of the TABLE 1.—TEMPORARY REVISIONS Model de Havilland TR Maintenance program manual DHC–8–102, DHC–8–103, and DHC–8–106 airplanes. DHC–8–201, and DHC–8–202 airplanes. DHC–8–301, DHC–8–311, and DHC–8–315 airplanes. AWL–98, dated April 12, 2006 ...... Part 2, ‘‘Airworthiness Limitations List,’’ of de Havilland Dash 8 Series 100 MPM, Product Support Manual (PSM) 1–8–7. Part 2, ‘‘Airworthiness Limitations List,’’ of de Havilland Dash 8 Series 200 MPM, PSM 1–82–7. Part 2, ‘‘Airworthiness Limitations List,’’ of de Havilland Dash 8 Series 300 MPM, PSM 1–83–7. AWL 2–35, dated April 12, 2006 ... AWL 3–103, dated April 12, 2006 Note 1: The revisions required by paragraph (f)(1) of this AD may be done by inserting a copy of the applicable TR into the applicable maintenance program manual. When the TR has been included in the general revision of the maintenance program, the general revision may be inserted into the maintenance program manual, provided the relevant information in the general revision listed in Table 2 of this AD, that is approved by the Manager, New York Aircraft Certification Office (ACO), FAA, or Transport Canada Civil Aviation (or its delegated agent); or unless the CDCCLs are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (g)(1) of this AD. is identical to that in the applicable TR, and the temporary revision may be removed. (2) After accomplishing the actions specified in paragraph (f)(1) of this AD, no alternative CDCCLs may be used unless the CDCCLs are part of a later revision of Part 2, ‘‘Airworthiness Limitations List,’’ of the applicable de Havilland Dash 8 Series MPM TABLE 2.—MPMS Model MPM DHC–8–102, DHC–8–103, and DHC–8–106 airplanes. DHC–8–201, and DHC–8–202 airplanes ........... Part 2, ‘‘Airworthiness Limitations List,’’ of de Havilland Dash 8 Series 100 MPM, PSM 1–8–7, Revision 17, dated April 19, 2005. Part 2, ‘‘Airworthiness Limitations List,’’ of de Havilland Dash 8 Series 200 MPM, PSM 1–82– 7, Revision 5, dated August 15, 2001. Part 2, ‘‘Airworthiness Limitations List,’’ of de Havilland Dash 8 Series 300 MPM, PSM 1–83– 7, Revision 16, dated August 15, 2001. DHC–8–301, DHC–8–311, and DHC–8–315 airplanes. FAA AD Differences Note 2: This AD differs from the MCAI and/or service information as follows: No differences. sroberts on PROD1PC70 with PROPOSALS Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, New York Aircraft Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Mazdak Hobbi, Aerospace Engineer, Airframe and Propulsion Branch, ANE–171, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone (516) 228–7330; fax (516) 794–5531. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal VerDate Aug<31>2005 17:20 Mar 10, 2008 Jkt 214001 inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120–0056. and the TRs specified in Table 1 of this AD, for related information. Issued in Renton, Washington, on March 5, 2008. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E8–4772 Filed 3–10–08; 8:45 am] BILLING CODE 4910–13–P Related Information (h) Refer to MCAI Canadian Airworthiness Directive CF–2008–03, dated January 3, 2008, PO 00000 Frm 00015 Fmt 4702 Sfmt 4702 E:\FR\FM\11MRP1.SGM 11MRP1

Agencies

[Federal Register Volume 73, Number 48 (Tuesday, March 11, 2008)]
[Proposed Rules]
[Pages 12912-12915]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: E8-4772]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2008-0266; Directorate Identifier 2008-NM-013-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier Model DHC-8-102, DHC-8-103, 
DHC-8-106, DHC-8-201, DHC-8-202, DHC-8-301, DHC-8-311, and DHC-8-315 
Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the 
products listed above. This proposed

[[Page 12913]]

AD results from mandatory continuing airworthiness information (MCAI) 
originated by an aviation authority of another country to identify and 
correct an unsafe condition on an aviation product. The MCAI describes 
the unsafe condition as:

    Bombardier Aerospace has completed a system safety review of the 
aircraft fuel system against fuel tank safety standards introduced 
in Chapter 525 of the Airworthiness Manual through Notice of 
Proposed Amendment (NPA) 2002-043. The identified non-compliances 
were then assessed using Transport Canada Policy Letter No. 525-001, 
to determine if mandatory corrective action is required.

    The assessment showed that it is necessary to introduce Critical 
Design Configuration Control Limitations (CDCCL), in order to 
preserve critical fuel tank system ignition source prevention 
features during configuration changes such as modifications and 
repairs, or during maintenance actions. Failure to preserve critical 
fuel tank system ignition source prevention features could result in 
a fuel tank explosion. * * *

The proposed AD would require actions that are intended to address the 
unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by April 10, 2008.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to https://
www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New 
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://
www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Mazdak Hobbi, Aerospace Engineer, 
Airframe and Propulsion Branch, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New 
York 11590; telephone (516) 228-7330; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2008-0266; 
Directorate Identifier 2008-NM-013-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to https://
www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2008-03, dated January 3, 2008 (referred to after this as ``the 
MCAI''), to correct an unsafe condition for the specified products. The 
MCAI states:

Bombardier Aerospace has completed a system safety review of the 
aircraft fuel system against fuel tank safety standards introduced 
in Chapter 525 of the Airworthiness Manual through Notice of 
Proposed Amendment (NPA) 2002-043. The identified non-compliances 
were then assessed using Transport Canada Policy Letter No. 525-001, 
to determine if mandatory corrective action is required.

The assessment showed that it is necessary to introduce Critical 
Design Configuration Control Limitations (CDCCL), in order to 
preserve critical fuel tank system ignition source prevention 
features during configuration changes such as modifications and 
repairs, or during maintenance actions. Failure to preserve critical 
fuel tank system ignition source prevention features could result in 
a fuel tank explosion. Revisions have been made to Part 2 
``Airworthiness Limitations List'' of the Maintenance Program 
Manuals of the affected models to introduce the required CDCCL.

The corrective action is revising the Airworthiness Limitations Section 
of the Instructions for Continued Airworthiness to include the CDCCL 
data. You may obtain further information by examining the MCAI in the 
AD docket.
    The FAA has examined the underlying safety issues involved in fuel 
tank explosions on several large transport airplanes, including the 
adequacy of existing regulations, the service history of airplanes 
subject to those regulations, and existing maintenance practices for 
fuel tank systems. As a result of those findings, we issued a 
regulation titled ``Transport Airplane Fuel Tank System Design Review, 
Flammability Reduction and Maintenance and Inspection Requirements'' 
(66 FR 23086, May 7, 2001). In addition to new airworthiness standards 
for transport airplanes and new maintenance requirements, this rule 
included Special Federal Aviation Regulation No. 88 (``SFAR 88,'' 
Amendment 21-78, and subsequent Amendments 21-82 and 21-83).
    Among other actions, SFAR 88 requires certain type design (i.e., 
type certificate (TC) and supplemental type certificate (STC)) holders 
to substantiate that their fuel tank systems can prevent ignition 
sources in the fuel tanks. This requirement applies to type design 
holders for large turbine-powered transport airplanes and for 
subsequent modifications to those airplanes. It requires them to 
perform design reviews and to develop design changes and maintenance 
procedures if their designs do not meet the new fuel tank safety 
standards. As explained in the preamble to the rule, we intended to 
adopt airworthiness directives to mandate any changes found necessary 
to address unsafe conditions identified as a result of these reviews.
    In evaluating these design reviews, we have established four 
criteria intended to define the unsafe conditions associated with fuel 
tank systems that require corrective actions. The percentage of 
operating time during which fuel tanks are exposed to flammable 
conditions is one of these criteria. The other three criteria address 
the failure types under evaluation: single failures, single failures in 
combination with a latent condition(s), and in-service failure 
experience. For all four criteria, the evaluations included 
consideration of previous actions taken that may mitigate the need for 
further action.
    We have determined that the actions identified in this AD are 
necessary to reduce the potential of ignition sources inside fuel 
tanks, which, in combination with flammable fuel vapors, could result 
in fuel tank explosions and consequent loss of the airplane.

Relevant Service Information

    Bombardier has issued de Havilland temporary revisions (TRs) to 
Part 2

[[Page 12914]]

``Airworthiness Limitations List'' (AWL) of the de Havilland Dash 8 
Series Maintenance Program Manuals (MPMs). The TRs are listed in the 
following table titled ``TRs to the DHC-8 MPMs.''

                          TRs to the DHC-8 MPMs
------------------------------------------------------------------------
        de Havilland TR              TR date          de Havilland MPM
------------------------------------------------------------------------
AWL-98........................  April 12, 2006...  Dash 8 Series 100
                                                    MPM, Product Support
                                                    Manual (PSM) 1-8-7.
AWL 2-35......................  April 12, 2006...  Dash 8 Series 200
                                                    MPM, PSM 1-82-7.
AWL 3-103.....................  April 12, 2006...  Dash 8 Series 300
                                                    MPM, PSM 1-83-7.
------------------------------------------------------------------------

The actions described in this service information are intended to 
correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.
    This proposed AD would allow revising the Airworthiness Limitations 
Section (ALS) of the Instructions for Continued Airworthiness in 
accordance with later revisions of the MPM as an acceptable method of 
compliance if the CDCCL is part of a later approved MPM revision, or if 
the CDCCL is approved as an alternative method of compliance (AMOC) in 
accordance with the procedures specified in paragraph (g)(1) of this 
proposed AD.
    In most ADs, we adopt a compliance time allowing a specified amount 
of time after the AD's effective date. In this case, however, the FAA 
has already issued regulations that require operators to revise their 
maintenance/inspection programs to address fuel tank safety issues. The 
compliance date for these regulations is December 16, 2008. To provide 
for coordinated implementation of these regulations and this proposed 
AD, we are using this same compliance date in this proposed AD.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have proposed different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
highlighted in a NOTE within the proposed AD.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 118 products of U.S. registry. We also estimate that 
it would take about 1 work-hour per product to comply with the basic 
requirements of this proposed AD. The average labor rate is $80 per 
work-hour. Based on these figures, we estimate the cost of the proposed 
AD on U.S. operators to be $9,440, or $80 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

Bombardier, Inc. (Formerly de Havilland, Inc.): Docket No. FAA-2008-
0266; Directorate Identifier 2008-NM-013-AD.

Comments Due Date

    (a) We must receive comments by April 10, 2008.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to all Bombardier Model DHC-8-102, DHC-8-
103, DHC-8-106, DHC-8-201, DHC-8-202, DHC-8-301, DHC-8-311, and DHC-
8-315 airplanes, certificated in any category, all serial numbers.

[[Page 12915]]

Subject

    (d) Air Transport Association (ATA) of America Code 28: Fuel.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:
Bombardier Aerospace has completed a system safety review of the 
aircraft fuel system against fuel tank safety standards introduced 
in Chapter 525 of the Airworthiness Manual through Notice of 
Proposed Amendment (NPA) 2002-043. The identified non-compliances 
were then assessed using Transport Canada Policy Letter No. 525-001, 
to determine if mandatory corrective action is required.

The assessment showed that it is necessary to introduce Critical 
Design Configuration Control Limitations (CDCCL), in order to 
preserve critical fuel tank system ignition source prevention 
features during configuration changes such as modifications and 
repairs, or during maintenance actions. Failure to preserve critical 
fuel tank system ignition source prevention features could result in 
a fuel tank explosion. Revisions have been made to Part 2 
``Airworthiness Limitations List'' of the Maintenance Program 
Manuals of the affected models to introduce the required CDCCL.

The corrective action is revising the Airworthiness Limitations 
Section of the Instructions for Continued Airworthiness to include 
the CDCCL data.

Actions and Compliance

    (f) Unless already done, do the following actions.
    (1) For all airplanes: Within 60 days after the effective date 
of this AD, or before December 16, 2008, whichever occurs first, 
revise the Airworthiness Limitations section of the Instructions for 
Continued Airworthiness to incorporate the CDCCL data specified in 
the applicable temporary revision (TR) to the applicable maintenance 
program manual (MPM). The TRs are listed in Table 1 of this AD.

                      Table 1.--Temporary Revisions
------------------------------------------------------------------------
                                                    Maintenance program
             Model               de Havilland TR           manual
------------------------------------------------------------------------
DHC-8-102, DHC-8-103, and DHC-  AWL-98, dated      Part 2,
 8-106 airplanes.                April 12, 2006.    ``Airworthiness
                                                    Limitations List,''
                                                    of de Havilland Dash
                                                    8 Series 100 MPM,
                                                    Product Support
                                                    Manual (PSM) 1-8-7.
DHC-8-201, and DHC-8-202        AWL 2-35, dated    Part 2,
 airplanes.                      April 12, 2006.    ``Airworthiness
                                                    Limitations List,''
                                                    of de Havilland Dash
                                                    8 Series 200 MPM,
                                                    PSM 1-82-7.
DHC-8-301, DHC-8-311, and DHC-  AWL 3-103, dated   Part 2,
 8-315 airplanes.                April 12, 2006.    ``Airworthiness
                                                    Limitations List,''
                                                    of de Havilland Dash
                                                    8 Series 300 MPM,
                                                    PSM 1-83-7.
------------------------------------------------------------------------


    Note 1: The revisions required by paragraph (f)(1) of this AD 
may be done by inserting a copy of the applicable TR into the 
applicable maintenance program manual. When the TR has been included 
in the general revision of the maintenance program, the general 
revision may be inserted into the maintenance program manual, 
provided the relevant information in the general revision is 
identical to that in the applicable TR, and the temporary revision 
may be removed.

    (2) After accomplishing the actions specified in paragraph 
(f)(1) of this AD, no alternative CDCCLs may be used unless the 
CDCCLs are part of a later revision of Part 2, ``Airworthiness 
Limitations List,'' of the applicable de Havilland Dash 8 Series MPM 
listed in Table 2 of this AD, that is approved by the Manager, New 
York Aircraft Certification Office (ACO), FAA, or Transport Canada 
Civil Aviation (or its delegated agent); or unless the CDCCLs are 
approved as an alternative method of compliance (AMOC) in accordance 
with the procedures specified in paragraph (g)(1) of this AD.

                             Table 2.--MPMs
------------------------------------------------------------------------
            Model                                 MPM
------------------------------------------------------------------------
DHC-8-102, DHC-8-103, and DHC- Part 2, ``Airworthiness Limitations
 8-106 airplanes.               List,'' of de Havilland Dash 8 Series
                                100 MPM, PSM 1-8-7, Revision 17, dated
                                April 19, 2005.
DHC-8-201, and DHC-8-202       Part 2, ``Airworthiness Limitations
 airplanes.                     List,'' of de Havilland Dash 8 Series
                                200 MPM, PSM 1-82-7, Revision 5, dated
                                August 15, 2001.
DHC-8-301, DHC-8-311, and DHC- Part 2, ``Airworthiness Limitations
 8-315 airplanes.               List,'' of de Havilland Dash 8 Series
                                300 MPM, PSM 1-83-7, Revision 16, dated
                                August 15, 2001.
------------------------------------------------------------------------

FAA AD Differences

    Note 2: This AD differs from the MCAI and/or service information 
as follows: No differences.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. Send information to ATTN: Mazdak Hobbi, Aerospace 
Engineer, Airframe and Propulsion Branch, ANE-171, FAA, New York 
Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, 
Westbury, New York 11590; telephone (516) 228-7330; fax (516) 794-
5531. Before using any approved AMOC on any airplane to which the 
AMOC applies, notify your appropriate principal inspector (PI) in 
the FAA Flight Standards District Office (FSDO), or lacking a PI, 
your local FSDO.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (h) Refer to MCAI Canadian Airworthiness Directive CF-2008-03, 
dated January 3, 2008, and the TRs specified in Table 1 of this AD, 
for related information.

    Issued in Renton, Washington, on March 5, 2008.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
 [FR Doc. E8-4772 Filed 3-10-08; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.