Federal Aviation Administration May 2007 – Federal Register Recent Federal Regulation Documents
Results 51 - 100 of 124
Airworthiness Directives; Turbomeca Arrius 2F Turboshaft Engines
The FAA is superseding an existing airworthiness directive (AD) for Turbomeca Arrius 2F turboshaft engines. That AD currently requires removing from service certain serial number (SN) fuel control units (FCUs) or replacing the constant delta pressure (delta P) diaphragm in those FCUs. This AD requires replacing all FCUs not incorporating modification Tf 55 with FCUs that incorporate modification Tf 55. This AD results from the European Aviation Safety Agency (EASA) and Turbomeca expanding the applicability to the full population of FCUs installed on Arrius 2F turboshaft engines. FCUs not incorporating modification Tf 55 are susceptible to having an improperly assembled constant delta P diaphragm. We are issuing this AD to prevent an uncommanded engine in-flight shutdown on a single-engine helicopter, resulting in a forced autorotation landing or an accident.
Airworthiness Directives; Pratt & Whitney Canada (P&WC) PW535A Turbofan Engines; Correction
The FAA is correcting airworthiness directive (AD) 2006-24-08. That AD applies to Pratt & Whitney Canada (P&WC) PW535A turbofan engines. We published that AD in the Federal Register on December 4, 2006 (71 FR 70284). The fuel manifold part number (P/N) 3025267-01 listed in paragraph (c) is incorrect. This document corrects that P/N. In all other respects, the original document remains the same.
Airworthiness Directives; Reims Aviation S.A. Model F406 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Dornier Luftfahrt GmbH Model 228 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; British Aerospace Regional Aircraft Model HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
RTCA Government/Industry Air Traffic Management Advisory Committee
The FAA is issuing this notice to advise the public of a meeting of RTCA Government/Industry Air Traffic Management Advisory Committee.
Proposed Establishment of Class E Airspace; Centreville, AL
This notice proposed to establish Class E airspace at Centreville, AL. An Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedure (SIAP) Runway (RWY) 10 has been developed for Bibb County Airport. As a result, controlled airspace extending upward from 700 feet Above Ground Level (AGL) is needed to contain the SIAP and for Instrument Flight Rules (IFR) operations at Bibb County Airport. The operating status of the airport will change from Visual Flight Rules (VFR) to include IFR operations concurrent with the publication of the SIAP.
Proposed Establishment of Class E Airspace; Vero Beach, FL
This notice proposes to establish Class E2 airspace at Vero Beach, FL. As a result of an evaluation, it has been determined Class E Airspace Designated as Surface Areas should be established for Vero Beach Municipal Airport. Miami Air Route Traffic Control Center has communications capabilities and weather observation reporting when the Vero Beach tower is closed. Therefore, the airport will meet criteria for Class E2 airspace. Class E2 surface area airspace is required when the control tower is closed to contain Standard Instrument Approach Procedures (SIAPs) and other Instrument Flight Rules (IFR) operations at the airport. This action would establish Class E2 airspace extending upward from the surface to and including 2,500 feet MSL within a 4.2- mile radius of the airport and within 3.2 miles each side of the 261[deg] bearing from the Vero Beach Nondirectional Radio Beacon (NDB) extending from the 4.2 mile radius of the Vero Beach Municipal Airport to 7 miles west of the NDB.
Public Notice for Waiver of Aeronautical Land-Use Assurance Rickenbacker International Airport Columbus, OH
The Federal Aviation Administration (FAA) is considering a proposal to change a portion of the airport from aeronautical use to non-aeronautical use and to authorize the release of 188.653 acres of vacant airport property previously used for agricultural purposes for the proposed development of bulk warehouse/distribution facilities as a component of the Rickenbacker Global Logistics Park. The land was acquired by the Rickenbacker Port Authority through three Quitclaim Deeds from the United States of American dated March 30, 1984, September 22, 2004 (amended and restated August 26, 2005) and May 16, 2005. There are no impacts to the airport by allowing the airport to dispose of the property. Approval does not constitute a commitment by the FAA to financially assist in the disposal of the subject airport property nor a determination of eligibility for grant-in-aid funding from the FAA. The CRAA will receive $4,245,000 for the parcel. In accordance with section 47107(h) of title 49, United States Code, this notice is required to be published in the Federal Register 30 days before modifying the land-use assurance that requires the property to be used for an aeronautical purpose.
Airworthiness Directives; Eurocopter France Model EC130 B4 Helicopters
This document proposes adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model EC 130 B4 helicopters, with certain twist grip assemblies installed. This proposal would require inspecting the pilot and co-pilot collective levers for proper bonding between the twist grip drive tubes and the control pinions and if debonding is present, replacing the collective levers before further flight. This proposal is prompted by one incident in which the engine remained at idle speed although the twist grip had been turned to the flight position. The actions specified by this proposed AD are intended to detect debonding between the twist grip drive tubes and the control pinions on the pilot and co-pilot collective levers to prevent loss of cockpit throttle control of the engine, and subsequent loss of control of the helicopter.
Airworthiness Directives; Pratt & Whitney (PW) PW4164, PW4168, and PW4168A Turbofan Engines
The FAA proposes to adopt a new airworthiness directive (AD) for PW PW4164, PW4168, and PW4168A turbofan engines with certain low pressure turbine (LPT) stage 4 disks, part number (P/N) 51N404, installed. This proposed AD would require removing certain LPT stage 4 disks, listed by serial number at the next piece-part exposure or within 7,500 cycles-since-new (CSN), whichever occurs first. This proposed AD results from a report of improperly manufactured LPT stage 4 disks. We are proposing this AD to prevent an uncontained engine failure due to low-cycle fatigue (LCF), which could result in damage to the airplane.
Airworthiness Directives; Eurocopter France Model EC130 B4 Helicopters
This amendment proposes adopting a new airworthiness directive (AD) for Eurocopter France (ECF) Model EC130 B4 helicopters. This proposal would require, within 100 hours time-in-service (TIS), modifying and testing the wiring of the battery overheat sensing circuit. This proposal is prompted by a malfunction in the battery overheat sensing circuit found during a scheduled inspection. The actions specified by this proposed AD are intended to correct the connection of the thermal switch to the cockpit indicator light, to notify the flight crew of an overheated battery, and to prevent a thermal runaway of the battery, an in-flight fire, and subsequent loss of control of the helicopter.
Ninth Meeting: RTCA Special Committee 206/EUROCAE WG 76 Plenary
The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 206: Aeronautical Information Services Data Link.
Airworthiness Directives; British Aerospace Regional Aircraft Model Jetstream HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Pacific Aerospace Limited, Model 750XL Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; British Aerospace Regional Aircraft Jetstream Model 3201 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Diamond Aircraft Industries GmbH Model DA 40 and DA 40F Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Human Space Flight Requirements for Crew and Space Flight Participants
This notice announces the Office of Management and Budget's (OMB) approval of the information collection requirement in the final rule published on December 15, 2006. The sections of the final rule pending approval of this information collection request are effective upon publication of this notice.
Petitions for Exemption; Summary of Petitions Received
This notice contains a summary of a certain petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of any petition or its final disposition.
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-145LR, -145XR, and -145MP Airplanes; and Model EMB-135BJ and -135LR Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain EMBRAER Model EMB-145LR, -145XR, and -145MP airplanes; and Model EMB-135BJ and -135LR airplanes. This AD requires replacing the electrical bonding clamps inside the fuel tanks and adjacent areas. This AD results from a report of the failure of a fitting clamp of an electrical bonding cable for the fuel tubing. We are issuing this AD to prevent loss of bonding protection in the interior of the fuel tanks or adjacent areas, and a consequent potential source of ignition in a fuel tank and possible fire or explosion.
Airworthiness Directives; Cessna Aircraft Company Models 208 and 208B Airplanes
The FAA is adopting a new airworthiness directive (AD) to supersede AD 2006-06-06, which applies to certain Cessna Aircraft Company (Cessna) Models 208 and 208B airplanes. AD 2006-06-06 currently requires you to incorporate information into the applicable section of the Airplane Flight Manual (AFM) and Pilot's Operating Handbook (POH) and requires you to install placards. Since we issued AD 2006-06-06, Cessna issued new S1 Known Icing Equipment AFM supplements and developed a low airspeed awareness system. Consequently, this AD requires you to incorporate the applicable AFM supplement revision and temporarily retain the requirements of AD 2006-06-06 until the above revisions are incorporated. One of the AFM requirements is the installation of a functional low airspeed awareness system to operate the airplane in known icing conditions. We are issuing this AD to assure that the pilot has enough information and the necessary equipment to prevent loss of control of the airplane while in-flight during icing conditions.
Airworthiness Directives; Boeing Model 747-400 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-400 series airplanes. This AD requires repetitive inspections for any crack in the upper deck floor beam at station 400, which include inspecting the floor beam web and chords, certain fastener holes at the intersection of the floor beam and frame on both sides of the airplane, and certain floor panel attachment fastener holes at the floor beam upper chords. This AD also requires corrective action if necessary. This AD results from several reports indicating that fatigue cracking was found in upper deck floor beams made from 7000 series aluminum alloy. We are issuing this AD to detect and correct cracking in the upper deck floor beam at station 400, which could extend and sever the floor beam. A severed floor beam could result in loss of controllability and rapid decompression of the airplane.
Airworthiness Directives; APEX Aircraft (Type Certificate No. A36EU Formerly Held by AVIONS MUDRY et CIE) Model CAP 10 B Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Cirrus Design Corporation Models SR20 and SR22 Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Cirrus Design Corporation (CDC) Models SR20 and SR22 airplanes. This proposed AD would require you to replace the pick-up collar support and nylon screws, of the Cirrus Airplane Parachute System (CAPS), with a new design pick-up collar support and custom tension screws. This proposed AD results from a CDC report of an in-flight CAPS activation where the parachute failed to successfully deploy. We are proposing this AD to correct pick-up collar support fasteners of the CAPS, which could result in the premature separation of the collar. This condition, if not corrected, could result in the parachute failing to successfully deploy (CAPS failure).
Airworthiness Directives; Allied Ag Cat Productions, Inc. (Type Certificate No. 1A16 Formerly Held by Schweizer Aircraft Corp.) G-164 Series Airplanes
We propose to supersede Airworthiness Directive (AD) 82-07-04, which applies to certain Allied Ag Cat Productions, Inc. (Ag Cat) G-164 series airplanes. AD 82-07-04 currently requires you to modify the fuel shut-off valve control by installation of a new stop-plate. Since we issued AD 82-07-04, we have determined the need to add airplane models and serial numbers that were not previously included in the applicability. Consequently, this proposed AD would retain the actions of AD 82-07-04 and add airplane models and serial numbers to the applicability. We are proposing this AD to prevent turning the fuel shut-off valve clockwise past the ``ON'' position stop which, if not corrected, could allow the fuel valve to be rotated to an unplacarded ``OFF'' position. This condition could lead to reduced fuel flow and consequent loss of engine power.
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135BJ Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: It has been found cases in which the drain mast of the water and waste system does not meet the SFAR-88 (Special Federal Aviation Regulation No. 88) requirements. In case of fuel leakage or fuel vapor release, the proximity of this mast with the fuel tank may cause fuel ignition, leading to a possible tank explosion.
Airworthiness Directives; Airbus Model A300-600 Series Airplanes and Model A310 Series Airplanes
The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Airbus Model A300-600, A310-200, and A310-300 series airplanes. The existing AD currently requires inspecting for certain serial numbers on elevators, and doing a detailed inspection, visual inspection with a low-angle light, and tap- test inspection of the upper and lower surfaces of the external skins on certain identified elevators for any damage (i.e., debonding of the graphite fiber reinforced plastic/Tedlar film protection, bulges, debonding of the honeycomb core to the carbon fiber reinforced plastic, abnormal surface reflections, and torn-out plies), and doing corrective actions if necessary. This proposed AD would also require inspecting for damage of the identified elevators in accordance with a new repetitive inspection program, at new repetitive intervals; and would provide an optional terminating action for the repetitive inspections. This proposed AD results from reports of damage caused by moisture/water inside the elevator. We are proposing this AD to detect and correct debonding of the skins on the elevators, which could cause reduced structural integrity of an elevator and reduced controllability of the airplane.
Airworthiness Directives; Boeing Model 757-200 and 757-300 Series Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Boeing Model 757-200 and 757-300 series airplanes. This proposed AD would require installing a copper bonding jumper between a ground and the clamp on the tube of the forward and aft gray water composite drain masts. This proposed AD results from a report of charred insulation blankets and burned wires around the forward gray water composite drain mast found during an inspection of the forward cargo compartment on a Model 767-300F airplane. We are proposing this AD to prevent a fire near a composite drain mast and possible disruption of the electrical power system due to a lightning strike on a composite drain mast, which could result in the loss of several functions essential for safe flight.
Standard Instrument Approach Procedures, Weather Takeoff Minimums; Miscellaneous Amendments
This amendment establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and/or Weather Takeoff Minimums for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, addition of new obstacles, or changes in air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Notice of the U.S. Air Force Supplemental Final Environmental Impact Statement and FAA Approval of the Record of Decision for the Realistic Bomber Training Initiative (RBTI)
The FAA is announcingadoption of the United States Air Force (USAF) Final Supplemental Environmental Impact Statement (SEIS) for the Realistic Bomber Training Initiative (RBTI), and approval of the FAA Record of Decision (ROD). The USAF proposal was to create airspace that allows B-52 and B-1 aircrews to receive much needed realistic combat training while maximizing their training time. RBTI includes the Lancer Military Operating Area (MOA) and the Instrument Military Training Route 178 (IR-178).
Notice of Adoption of the U.S. Air Force Final Environmental Impact Statement and Approval of the Federal Aviation Administration Record of Decision for the New Mexico Training Range Initiative (NMTRI)
The FAA is announcing its Adoption of the United States Air Force (USAF) Final Environmental Impact Statement (FEIS) for the New Mexico Training Range Initiative and approval of the FAA Record of Decision (ROD). The New Mexico Training Range Initiative (NMTRI) is the USAF initiative to create airspace that allows mainly F-16 and aircrews to receive much needed realistic combat training while maximizing their training time. NMTRI includes the Pecos MOA complex.
Modification of Class E Airspace; Canby, MN
This action amends Title 14 Code of Federal Regulations, part 71 (14 CFR 71) by modifying Class E airspace at Canby, Myers Field, MN. Standard Instrument Approach Procedures have been developed by Canby, Myers Field, MN. Additional controlled airspace extending upward from the surface and upward from 700 feet above the surface of the earth is needed to contain aircraft executing these approaches. This action increases the area of the existing controlled airspace for Canby, Myers Field, MN.
Modification of Class E Airspace; Manhattan, KS
This action amends Title 14 Code of Federal Regulations, part 71 (14 CFR 71) by modifying the legal description of Class D airspace and Class E airspace at Manhattan Municipal Airport, KS. The establishment of adjacent Class D airspace at Fort Riley, Marshall Army Airfield, KS requires this modification. The intended effect of this rule is to provide controlled airspace of appropriate dimensions to protect aircraft operating in these areas.
Modification of Class E Airspace; Monticello, IA
This action amends Title 14 Code of Federal Regulations, part 71 (14 CFR 71) by modifying the Class E airspace area at Monticello Regional Airport, IA. The cancellation of the Non Directional Beacon (NDB) Instrument Approach Procedure (IAP) and subsequent decommissioning of the Monticello NDB requires modification of the Class E airspace area extending upward from 700 feet above the surface of the earth. The intended effect of this rule is to provide controlled airspace of appropriate dimensions to protect aircraft executing Standard Instrument Approach Procedures (SIAP) to Monticello Regional Airport, IA.
Modification of Class E Airspace; Marshalltown, IA
This action amends Title 14 Code of Federal Regulations, part 71q (14 CFR 71) by modifying the Class E airspace area at Marshalltown Municipal Airport, IA. The cancellation of the Non Directional Beacon (NDB) Instrument Approach Procedure (IAP) and subsequent decommissioning of the Marshalltown NDB requires modification of the Class E airspace area extending upward from 700 feet above the surface of the earth. The intended effect of this rule is to provide controlled airspace of appropriate dimensions to protect aircraft executing Standard Instrument Approach Procedures (SIAP) to Marshalltown Municipal Airport, IA.
Modification of Class E Airspace; Canby, MN
This action amends Title 14 Code of Federal Regulations, part 71 (14 CFR part 71) by modifying Class E airspace at Canby, Myers Field, MN. Standard Instrument Approach Procedures have been developed for Canby, Myers Field, MN. Additional controlled airspace extending upward from the surface and upward from 700 feet above the surface of the earth is needed to contain aircraft executing these approaches. This action increases the area of the existing controlled airspace for Canby, Myers Field, MN.
Modification of Class E Airspace; Manhattan, KS
This action amends Title 14 Code of Federal Regulations, part 71 (14 CFR part 71) by modifying the legal description of Class D airspace and Class E airspace at Manhattan Municipal Airport, KS. The establishment of adjacent Class D airspace at Fort Riley, Marshall Army Airfield, KS requires this modification. The intended effect of this rule is to provide controlled airspace of appropriate dimensions to protect aircraft operating in these areas.
Modification of Class E Airspace; Monticello, IA
This action amends Title 14 Code of Federal Regulations, part 71 (14 CFR part 71) by modifying the Class E airspace area at Monticello Regional Airport, IA. The cancellation of the Non Directional Beacon (NDB) Instrument Approach Procedure (IAP) and subsequent decommissioning of the Monticello NDB requires modification of the Class E airspace area extending upward from 700 feet above the surface of the earth. The intended effect of this rule is to provide controlled airspace of appropriate dimensions to protect aircraft executing Standard Instrument Approach Procedures (SIAP) to Monticello Regional Airport, IA.
Modification of Class E Airspace; Marshalltown, IA
This action amends Title 14 Code of Federal Regulations, part 71 (14 CFR part 71) by modifying the Class E airspace area at Marshalltown Municipal Airport, IA. The cancellation of the Non Directional Beacon (NDB) Instrument Approach Procedure (IAP) and subsequent decommissioning of the Marshalltown NDB requires modification of the Class E airspace area extending upward from 700 feet above the surface of the earth. The intended effect of this rule is to provide controlled airspace of appropriate dimensions to protect aircraft executing Standard Instrument Approach Procedures (SIAP) to Marshalltown Municipal Airport, IA.
Standard Instrument Approach Procedures; Miscellaneous Amendments
This amendment amends Standard Instrument Approach Procedures (SIAPs) for operations at certain airports. These regulatory actions are needed because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, addition of new obstacles, or changes in air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Notice of Availability of Written Reevaluation and Record of Decision; Centerfield Taxiway; Logan International Airport; Boston, MA
The Federal Aviation Administration (FAA) announces availability of a Written Reevaluation and Record of Decision (ROD) for a Centerfield Taxiway at Logan International Airport, Boston, Massachusetts. The ROD follows the issuance of a Final Environmental Impact Statement for the Airside Improvement Planning Project, issued in June 2002, and subsequent Record of Decision (August 2002) that approved several airport development projects but deferred a decision on the Centerfield Taxiway. The FAA is now documenting its decision to approve the Centerfield Taxiway and take action toward making federal funds available for its construction. FAA's Record of Decision may be accessed on FAA's public Web site: www.faa.gov/airportsairtraffic.
Notice of Intent To Rule on Application 06-19-C-00-ORD To Impose and Use the Revenue From a Passenger Facility Charge (PFC) at Chicago O'Hare International Airport, Chicago, IL
The FAA proposes to rule and invites public comment on the applications to impose and use the revenue from a PFC at Chicago O'Hare International Airport under the provisions of the 49 U.S.C. 40117 and part 158 of the Federal Aviation Regulations (14 CFR part 158). Due to the fact that the two applications involve projects associated with the O'Hare Modernization Program, the FAA has elected to combine the two applications and will issue one Final Agency Decision for the combined applications.
Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals
The FAA publishes a monthly notice, as appropriate, of PFC approvals and disapprovals under the provisions of the Aviation Safety and Capacity Expansion Act of 1990 (Title IX of the Omnibus Budget Reconciliation Act of 1990) (Public Law 101-508) and Part 158 of the Federal Aviation Regulations (14 CFR part 158) and Part 158 of the Federal Aviation Regulations (14 CFR part 1580. This notice is published pursuant to paragraph d of Sec. 158.29.
Revision of Class E Airspace; Port Heiden, AK
This action revises Class E airspace at Port Heiden, AK to provide adequate controlled airspace to contain aircraft executing Standard Instrument Approach Procedures (SIAPs). Two new Standard Instrument Approach Procedures (SIAPs) are being developed, and two procedures are being amended for the Port Heiden Airport. A Departure Procedure (DP) is also being amended. This action revises existing Class E airspace upward from 700 feet (ft.) and 1,200 ft. above the surface at Port Heiden Airport, Port Heiden, AK.
Revision of Class E Airspace; Kodiak, AK
This action revises Class E airspace at Kodiak, AK to provide adequate controlled airspace to contain aircraft executing Standard Instrument Approach Procedures (SIAPs). Four Standard Instrument Approach Procedures (SIAPs) are being amended for the Kodiak Airport. A Standard Instrument Departure (SID) and a Departure Procedure (DP) are also being amended. This action revises existing Class E airspace upward from the surface, from 700 feet (ft.) and 1,200 ft. above the surface at Kodiak Airport, Kodiak, AK.
Airworthiness Directives; Pacific Aerospace Limited Model 750XL Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Turbomeca Arriel 2B1 Turboshaft Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Turbomeca Arriel 2B Series Turboshaft Engines
We are superseding an existing airworthiness directive (AD) by adopting a new AD for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; General Electric Company (GE) GE90 Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for GE GE90-110B1, -113B, and -115B series turbofan engines with certain Turbine Center Frames (TCFs) installed. This AD requires removing certain TCFs, listed by part number (P/N) in this AD, from service before exceeding 14,300 flight cycles. This AD results from a report that GE inadvertently omitted some TCF P/Ns from the Airworthiness Limitations Section (ALS) of the engine manual. We are issuing this AD to prevent structural failure of the TCF with uncontained failure of low pressure turbine (LPT) rotating parts. Uncontained failure of the LPT rotating parts could result in damage to the airplane and possible loss of control of the airplane.
Extended Operations (ETOPS) of Multi-Engine Airplanes
The Federal Aviation Administration is correcting a final rule published in the Federal Register on January 16, 2007 (72 FR 1808). That final rule applied to air carrier (part 121), commuter, and on- demand (part 135) turbine powered multi-engine airplanes used in passenger-carrying, and some all-cargo, extended-range operations. This amendment adds the Office of Management and Budget (OMB) Information Collection Control Number indicating approval of the information collection requirements of the final rule. This amendment also makes three corrections: In part 135, it corrects the dual maintenance paragraph to conform to part 121 and deletes a redundant defining of ``adequate airport''; in part 121 it corrects the rule language applicable to those persons who must accomplish and certify by signature the completion of ETOPS tasks; and in parts 121 and 135 it corrects the hours required for notification of maintenance problems based on an earlier FAA rulemaking. None of these changes is substantive, but will clarify the final rule for the affected public.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.