Federal Aviation Administration January 29, 2007 – Federal Register Recent Federal Regulation Documents
Results 1 - 7 of 7
Airworthiness Directives; Boeing Model 777-200, -300, and -300ER Series Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Boeing Model 777-200, -300, and -300ER series airplanes. This proposed AD would require installing Teflon sleeving under the clamps of the wire bundles routed along the fuel tank boundary structure, and cap sealing certain penetrating fasteners of the main and center fuel tanks. This proposed AD results from fuel system reviews conducted by the manufacturer. We are proposing this AD to prevent electrical arcing on the fuel tank boundary structure or inside the fuel tanks, which could result in a fire or explosion.
Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Tay 611-8, Tay 620-15, Tay 650-15, and Tay 651-54 Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for Rolls-Royce Deutschland Ltd & Co KG (RRD) Tay 611-8, Tay 620-15, Tay 650-15, and Tay 651-54 series turbofan engines, with certain low pressure (LP) compressor modules installed. This AD requires an ultrasonic inspection (UI) of LP compressor fan blades for cracks, within 30 days after the effective date of the AD on certain serial number (SN) Tay 650-15 engines. This AD also requires initial and repetitive UIs of LP compressor fan blades on all engines. This AD also requires, for Tay 650-15 and Tay 651-54 engines, UIs of LP compressor fan blades whenever the blade set is removed from one engine and installed on a different engine. This AD results from a report that a set of LP compressor fan blades failed before reaching the LP compressor fan blade full published life limit. We are issuing this AD to prevent LP compressor fan blades from failing due to blade root cracks, leading to uncontained engine failure and damage to the airplane.
Airworthiness Directives; Boeing Model 747 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 747 airplanes. This AD requires repetitive inspections for cracking of the web of the station (STA) 2360 aft pressure bulkhead around the fastener heads in the critical fastener rows in the web lap joints, from the Y-chord to the inner ring; and repair if necessary. This AD also requires a modification, which terminates the repetitive inspections. This AD results from analysis by the manufacturer that the radial lap splices of the STA 2360 aft pressure bulkhead are subject to widespread fatigue damage. We are issuing this AD to detect and correct cracking of the bulkhead web at multiple sites along the radial lap splice, which could join together to form cracks of critical length, and result in rapid decompression and loss of control of the airplane.
Airworthiness Directives; Boeing Model 767-200 and -300 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD) that applies to certain Boeing Model 767-200, -300, and -300F series airplanes. That AD currently requires an inspection of visually accessible areas for indications of overheating of the heater tape attached to the potable water fill and drain lines in the forward and aft cargo compartments, exposed foam insulation or missing or damaged protective tape around the potable water fill and drain lines, and debris or contaminants on or near the potable water fill and drain lines. That AD also requires corrective action, as necessary. This new AD requires repetitive inspections of the forward and aft cargo compartments, as applicable, for discrepancies of the potable water supply and gray water drain lines; and applicable corrective actions if necessary. This AD also requires replacing the heater tapes on the potable water supply and gray water drain lines of the forward and aft cargo compartments, as applicable, with new ribbon heaters, or deactivating and removing any defective heater tape and wrapping the drain line with foam insulation; either action ends the repetitive inspections. This AD results from a report of a fire in the aft cargo compartment. We are issuing this AD to prevent overheating of the heater tape on potable water fill and drain lines, which may ignite accumulated debris or contaminants on or near the potable water fill and drain lines, resulting in a fire in the airplane.
Airworthiness Directives; Boeing Model 757 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 757 airplanes. This AD requires inspecting certain power feeder wire bundles for damage, inspecting the support clamps for these wire bundles to determine whether the clamps are properly installed, and performing corrective actions if necessary. This AD results from a report that a power feeder wire bundle chafed against the number six auxiliary slat track, causing electrical wires in the bundle to arc, which damaged both the auxiliary slat track and power feeder wires. We are issuing this AD to prevent arcing that could be a possible ignition source for leaked flammable fluids, which could result in a fire. Arcing could also result in a loss of power from the generator connected to the power feeder wire bundle, and consequent loss of systems, which could reduce controllability of the airplane.
Airworthiness Directives; Bombardier Model DHC-8-100, -200, and -300 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Bombardier Model DHC-8-100, -200, and - 300 series airplanes. That AD currently requires modification of the flight compartment door; repetitive inspections for wear of the flight compartment door hinges following modification; and repair or replacement of the hinges with new hinges if necessary. This new AD requires using revised procedures for modifying and inspecting the flight compartment door and reduces the applicability of the existing AD. This AD results from a determination that certain cockpit doors are no longer subject to the existing requirements. We are issuing this AD to prevent failure of the alternate release mechanism of the flight compartment door, which could delay or impede the evacuation of the flightcrew during an emergency. This failure also could result in the flightcrew not being able to assist passengers in the event of an emergency.
Airworthiness Directives; Airbus Model A300 B4-605R Airplanes and Model A310-308, -324, and -325 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A300 B4-605R airplanes and Model A310-308, -324, and -325 airplanes. This AD requires modifying the Bruce floor plan electrical emergency path marking system (FPEEPMS) and, for certain airplanes, modifying the automatic switching of the emergency lighting system. This AD results from a report that in the case of vertical separation of the fuselage forward of door 1, the FPEEPMS and the exit signs do not turn on. We are issuing this AD to prevent inadequate lighting and marking of the escape path, which could delay or impede the flightcrew and passengers when exiting the airplane during an emergency landing.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
