Federal Aviation Administration October 4, 2005 – Federal Register Recent Federal Regulation Documents

The FAA is superseding two existing airworthiness directives (AD), which apply to certain Boeing transport category airplanes. One AD currently requires doing certain inspections to detect cracks and corrosion around the lower bearing of the actuator attach fittings of the inboard and outboard flaps; repairing if necessary; and either overhauling the fittings or replacing them, which ends certain repetitive inspections. The other AD currently requires certain other inspections to detect discrepancies of the actuator attach fittings of the flaps, and follow-on and corrective actions if necessary, which ends the repetitive inspections of the first AD. For certain airplanes, this AD requires new inspections for discrepancies of the actuator attach fittings of the flaps, and follow-on and corrective actions if necessary, which ends the repetitive inspections of both existing ADs. For all airplanes, this AD requires repetitive overhaul/replacements of the actuator attach fittings of both the inboard and outboard flaps. This AD results from reports of cracks of the actuator attach fittings of the trailing edge flaps. We are issuing this AD to prevent cracking and other damage of the actuator attach fittings of the trailing edge flaps, which could result in abnormal operation or retraction of a trailing edge flap, and possible loss of controllability of the airplane.

These special conditions are issued for Dassault-Aviation Mystere-Falcon 50 airplanes modified by Premier Air Center. These modified airplanes will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. The modification incorporates the installation of Universal Avionics EFI-890 Electronic Flight Displays and Rockwell Collins AHS-3000A Attitude Heading Reference Systems (AHRS) that perform critical functions. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for the protection of these systems from the effects of high-intensity radiated fields (HIRF). These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

These special conditions are issued for the Boeing Model 720B airplane. The airplane will have novel and unusual design features when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. The modification incorporates the installation of dual Honeywell AM-250 digital altimeters. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for the protection of these systems from the effects of high-intensity radiated fields (HIRF). These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that provided by the existing airworthiness standards.

This action proposes to revise a segment of Jet Route J-158 between the Malad City, ID, Very High Frequency Omni-directional Range/ Distance Measuring Equipment (VOR/DME) and the Muddy Mountain, WY, Very High Frequency Omni-directional Range/Tactical Air Navigation (VORTAC). Specifically, the FAA is proposing to realign the route from Malad City, ID, to Big Piney, WY, VOR/DME to Muddy Mountain, WY. This proposed action would replace the sector taken out of service, reduce controller workload, and enhance the National Airspace System.

The FAA is superseding an existing airworthiness directive (AD) for Rolls-Royce plc (RR) RB211 Trent 875, 877, 884, 892, 892B, and 895 series turbofan engines. That AD currently requires repetitive application of dry film lubricant (DFL) to low pressure compressor (LPC) fan blade roots. This AD requires the same actions but at more frequent intervals than the existing AD. This AD also adds the Trent 884B engine to the list of engine models affected, adds a fan blade part number (P/N) to the affected list of fan blades, and relaxes the initial DFL repetitive application compliance time for certain fan blades that have never been removed from the disk. This AD results from discovering DFL in worse condition than anticipated on fan blades fitted to disks previously run for a significant period. This AD also results from the need to update the list of engine models affected, and to update the list of fan blade part numbers affected. We are issuing this AD to prevent LPC fan blade loss, which could result in an uncontained engine failure and possible aircraft damage.

This amendment amends Standard Instrument Approach Procedures (SIAPs) for operations at certain airports. These regulatory actions are needed because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, addition of new obstacles, or changes in air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

The FAA is adopting a new airworthiness directive (AD) for all Airbus Model A330-243, -341, -342, and -343 airplanes. This AD requires revising the airplane flight manual to provide the flightcrew with new, ground ice-shedding procedures during long taxi periods in certain icing conditions. This AD results from reports of engine damage to the blades of the first stage of the intermediate pressure compressor due to ice accumulation. We are issuing this AD to prevent engine damage due to ice accumulation, which could result in an engine shutdown and cause the flightcrew to divert to the nearest available airport.