Department of Transportation October 14, 2020 – Federal Register Recent Federal Regulation Documents

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The collection involves the requirement for Helicopter Air Ambulance Operators to report certain information to the FAA. The FAA collects 14 pieces of data from helicopter air ambulance operators, 8 of which are mandated in the report to Congress. We collect data on the following: number of helicopters, helicopter base locations, number of hours the helicopters are flown, number of patients transported, number of transportation requests accepted or denied, number of accidents, number of instrument flight hours flown, number of night flight hours flown, number of incidents, and the rate of accidents or incidents per 100,000 flight hours. The information to be collected will be used in helping the FAA develop risk mitigation strategies and provide information to Congress.

This notice sets forth the reasons for the denial of a petition submitted on April 10, 2020, by Mr. Surjit Singh to NHTSA's Office of Defects Investigation (ODI). The petition requests that the Agency investigate Model Year 2013 Mercedes-Benz E350 vehicles for alleged premature rear brake line corrosion failure. NHTSA opened Defect Petition DP20-004 to evaluate the petitioner's request. After reviewing the information provided by the petitioner and available NHTSA complaint and Early Warning Reporting (EWR) data, NHTSA has concluded that there is insufficient evidence to pursue further action at this time. Accordingly, the Agency has denied the petition.

The FAA is superseding Airworthiness Directive (AD) 2015-14- 01, which applied to certain Bombardier, Inc., Model DHC-8-400 series airplanes. AD 2015-14-01 required a detailed inspection for loose bolts on the aft translating door crank assembly, and removal and reinstallation of the bolts. This AD retains the inspections of AD 2015-14-01 and adds airplanes to the applicability. For all airplanes, this AD also requires a modification of the door crank handle, which will terminate the inspection requirements. This AD was prompted by reports of loose bolts that are intended to secure the translating door crank assembly to the outside handle shaft, and of sealant missing from these bolts on another translating door. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A300 F4-600R series airplanes. This AD was prompted by a report of damaged main deck cargo crossbeams on the right-hand side, between certain frame locations. This AD requires repetitive detailed inspections of the affected main deck cargo crossbeams for any damage, and depending on findings, accomplishment of applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA proposes to supersede airworthiness directive (AD) 82- 20-05 for Societe Nationale Industrielle Aerospatiale (now Airbus Helicopters) Model AS-350 and AS-355 series helicopters. AD 82-20-05 requires inspecting and establishing a life limit for the tail rotor (TR) drive shaft bearing (bearing). Since the FAA issued AD 82-20-05, inconsistencies have been identified between inspections and maintenance actions required by ADs and inspections and maintenance actions specified in the applicable maintenance manual. This proposed AD would require replacing certain part-numbered TR bearings with one part-numbered bearing and repetitively inspecting one part-numbered bearing. The actions of this proposed AD are intended to address an unsafe condition on these products.

In response to public input received as part of the rulemaking process, PHMSA is proposing to revise the Federal Pipeline Safety Regulations to amend the requirements for gas transmission pipeline segments that experience a change in class location. Under the existing regulations, pipeline segments located in areas where the population density has significantly increased must perform one of the following actions: Reduce the pressure of the pipeline segment, pressure test the pipeline segment to higher standards, or replace the pipeline segment. This proposed rule would add an alternative set of requirements operators could use, based on implementing integrity management principles and pipe eligibility criteria, to manage certain pipeline segments where the class location has changed from a Class 1 location to a Class 3 location. Through required periodic assessments, repair criteria, and other extra preventive and mitigative measures, PHMSA expects this alternative approach would provide long-term safety benefits consistent with the current natural gas pipeline safety rules while also providing cost savings for pipeline operators.