Department of Transportation September 18, 2018 – Federal Register Recent Federal Regulation Documents
Results 1 - 11 of 11
Operating Limitations at New York Laguardia Airport
This action extends the Order Limiting Operations at New York LaGuardia Airport (LGA) published on December 27, 2006, as most recently extended May 25, 2016. The Order remains effective until October 24, 2020.
Hazardous Materials: Emergency Waiver No. 6
The Pipeline and Hazardous Materials Safety Administration is issuing an emergency waiver order to persons conducting operations under the direction of Environmental Protection Agency (EPA) Regions 3 or 4 or United States Coast Guard (USCG) Fifth or Seventh Districts within the Hurricane Florence emergency areas of South Carolina, North Carolina, and Virginia. The Waiver is granted to support the EPA and USCG in taking appropriate actions to prepare for, respond to, and recover from a threat to public health, welfare, or the environment caused by actual or potential oil and hazardous materials incidents resulting from Hurricane Florence. This Waiver Order is effective immediately and shall remain in effect for 30 days from the date of issuance.
Amendment of the Prohibition Against Certain Flights in the Pyongyang Flight Information Region (FIR) (ZKKP)
This action amends the prohibition against certain flight operations in the Pyongyang Flight Information Region (FIR) (ZKKP) by all: U.S. air carriers; U.S. commercial operators; persons exercising the privileges of an airman certificate issued by the FAA, except when such persons are operating U.S.-registered aircraft for a foreign air carrier; and operators of U.S.-registered civil aircraft, except where the operator of such aircraft is a foreign air carrier. The FAA is also providing an approval process and exemption information for this Special Federal Aviation Regulations (SFAR), consistent with the approval process and exemption information for more recently published flight prohibition SFARs. This final rule will remain in effect for 2 years.
Airworthiness Directives; Bombardier, Inc., Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This proposed AD was prompted by reports of drainage holes on the belly fairing forward and middle access panels being obstructed with sealant. This proposed AD would require inspecting for and removing all sealant blocking the drainage holes on the belly fairing forward and middle access panels. We are proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Weatherly Aircraft Company
We propose to adopt a new airworthiness directive (AD) for all Weatherly Aircraft Company (Weatherly) Models 201, 201A, 201B, 201C, 620, 620A, 620B, 620B-TG, and 620TP airplanes. This proposed AD was prompted by reports of fatigue cracking of the center wing and outer wing spar hinge brackets due to corrosion pitting. This proposed AD would require repetitive inspections of the wing hinge brackets, pins, and wing spar structure with repair or replacement of parts as necessary. We are proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 and A310 series airplanes; and Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). This AD was prompted by a determination that new or more restrictive maintenance requirements and airworthiness limitations are necessary. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new or more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes); and Model A310 series airplanes. This AD was prompted by a determination that more restrictive maintenance requirements and airworthiness limitations are necessary. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new or more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes), and Model A310 series airplanes. This AD was prompted by a determination that new or more restrictive maintenance requirements and airworthiness limitations are necessary. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new or more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 series airplanes. This AD was prompted by a revision of an airworthiness limitation items (ALI) document. This AD requires revising the maintenance or inspection program, as applicable, to incorporate the specified maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Learjet, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Learjet, Inc. Models 28, 29, 31, 31A, 35, 35A, 36, 36A, 55, 55B, 55C, and 60 airplanes. This AD was prompted by fatigue cracks initiating in the flap support structure due to repetitive flap loads, which has caused flap nose roller support bracket failure. This AD requires replacement of the flap nose roller fitting, nose roller support bracket, and adjacent rib support structure with improved components. We are issuing this AD to address the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
