Airworthiness Directives; Airbus SAS Airplanes, 47056-47059 [2018-19858]

Download as PDF 47056 Federal Register / Vol. 83, No. 181 / Tuesday, September 18, 2018 / Rules and Regulations (k) Related Information (g) Revision of Maintenance or Inspection Program Within 90 days after the effective date of this AD, revise the maintenance or inspection program, as applicable, to incorporate Airbus A310 Airworthiness Limitations Section (ALS) Part 4, ‘‘System Equipment Maintenance Requirements (SEMR),’’ Revision 03, dated August 28, 2017; or A300– 600 Airworthiness Limitations Section (ALS) Part 4, ‘‘System Equipment Maintenance Requirements (SEMR),’’ Revision 03, dated August 28, 2017; as applicable. The initial compliance time for doing the revised actions is at the applicable time specified in Airbus A310 Airworthiness Limitations Section (ALS) Part 4, ‘‘System Equipment Maintenance Requirements (SEMR),’’ Revision 03, dated August 28, 2017, or A300– 600 Airworthiness Limitations Section (ALS) Part 4, ‘‘System Equipment Maintenance Requirements (SEMR),’’ Revision 03, dated August 28, 2017; as applicable; or within 90 days after the effective date of this AD; whichever occurs later. (h) No Alternative Actions or Intervals After the maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections) or intervals may be used unless the actions and intervals are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (j)(1) of this AD. (i) Terminating Action for AD 2015–02–16 Accomplishing the actions required by this AD terminates all requirements of AD 2015– 02–16. daltland on DSKBBV9HB2PROD with RULES (j) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (k)(2) of this AD. Information may be emailed to: 9-ANM-116-AMOCREQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or the European Aviation Safety Agency (EASA); or Airbus SAS’s EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOAauthorized signature. VerDate Sep<11>2014 16:42 Sep 17, 2018 Jkt 244001 DEPARTMENT OF TRANSPORTATION (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD 2017–0202, dated October 12, 2017, for related information. This MCAI may be found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2018–0396. (2) For more information about this AD, contact Dan Rodina, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206– 231–3225. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) Airbus A300–600 Airworthiness Limitations Section (ALS) Part 4, ‘‘System Equipment Maintenance Requirements (SEMR),’’ Revision 03, dated August 28, 2017. (ii) Airbus A310 Airworthiness Limitations Section (ALS) Part 4, ‘‘System Equipment Maintenance Requirements (SEMR),’’ Revision 03, dated August 28, 2017. (3) For service information identified in this AD, contact Airbus SAS, Airworthiness Office—EAW, Rond-Point Emile Dewoitine No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 51; email account.airworth-eas@ airbus.com; internet https://www.airbus.com. (4) You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https:// www.archives.gov/federal-register/cfr/ibrlocations.html. Issued in Des Moines, Washington, on August 24, 2018. James Cashdollar, Acting Director, System Oversight Division, Aircraft Certification Service. [FR Doc. 2018–19856 Filed 9–17–18; 8:45 am] BILLING CODE 4910–13–P PO 00000 Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2018–0364; Product Identifier 2017–NM–154–AD; Amendment 39–19398; AD 2018–18–19] RIN 2120–AA64 Airworthiness Directives; Airbus SAS Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. AGENCY: We are adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 and A310 series airplanes; and Model A300 B4– 600, B4–600R, and F4–600R series airplanes, and Model A300 C4–605R Variant F airplanes (collectively called Model A300–600 series airplanes). This AD was prompted by a determination that new or more restrictive maintenance requirements and airworthiness limitations are necessary. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new or more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products. DATES: This AD is effective October 23, 2018. The Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD as of October 23, 2018. ADDRESSES: For service information identified in this final rule, contact Airbus SAS, Airworthiness Office— EAW, Rond-Point Emile Dewoitine No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 51; email account.airwortheas@airbus.com; internet https:// www.airbus.com. You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. It is also available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2018– 0364. SUMMARY: Examining the AD Docket You may examine the AD docket on the internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2018– 0364; or in person at Docket Operations Frm 00030 Fmt 4700 Sfmt 4700 E:\FR\FM\18SER1.SGM 18SER1 Federal Register / Vol. 83, No. 181 / Tuesday, September 18, 2018 / Rules and Regulations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, the regulatory evaluation, any comments received, and other information. The address for Docket Operations (phone: 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206–231–3225. SUPPLEMENTARY INFORMATION: daltland on DSKBBV9HB2PROD with RULES Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to all Airbus SAS Model A300 and A310 series airplanes; and Model A300 B4–600, B4–600R, and F4–600R series airplanes, and Model A300 C4– 605R Variant F airplanes (collectively called Model A300–600 series airplanes). The NPRM published in the Federal Register on May 14, 2018 (83 FR 22219). The NPRM was prompted by a determination that new or more restrictive maintenance requirements and airworthiness limitations are necessary. The NPRM proposed to require revising the maintenance or inspection program, as applicable, to incorporate new or more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to prevent fatigue damage in principal structural elements, which could result in reduced structural integrity of the airplane. The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2017–0204, dated October 12, 2017 (referred to after this as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition for all Airbus SAS Model A300 and A310 series airplanes; and Model A300 B4–600, B4–600R, and F4–600R series airplanes, and Model A300 C4–605R Variant F airplanes (collectively called Model A300–600 series airplanes). The MCAI states: The airworthiness limitations for the Airbus A300, A310, A300–600 and A300– 600ST family aeroplanes, which are approved by EASA, are currently defined and published in the Airbus A300, A310 and A300–600 Airworthiness Limitations Section (ALS) documents. The Safe Life Airworthiness Limitation Items are specified in the A300, A310 and A300–600 (including the A300–600ST) ALS Part 1 documents. VerDate Sep<11>2014 16:42 Sep 17, 2018 Jkt 244001 These instructions have been identified as mandatory for continuing airworthiness. Failure to accomplish these instructions could result in an unsafe condition. EASA previously issued AD 2013–0248 [which corresponds to FAA AD 2015–22–05, Amendment 39–18310 (80 FR 69846, November 12, 2015) (‘‘AD 2015–22–05’’)] to require the implementation of the instructions and airworthiness limitations as specified in Airbus A300, A310 and A300– 600 ALS Part 1 documents at Revision 01. Since that [EASA] AD was issued, improvement of safe life component selection and life extension campaigns resulted in life limitations changes, among others new or more restrictive life limitations, approved by EASA. Consequently, Airbus published Revision 02 of the A300, A310 and A300–600 ALS Part 1, compiling all ALS Part 1 changes approved since previous Revision 01. For the reason described above, this [EASA] AD retains the requirements of EASA AD 2013–0248, which is superseded, and requires accomplishment of the actions specified in A300 ALS Part 1 Revision 02, A310 ALS Part 1 Revision 02 and A300–600 ALS Part 1 Revision 02. This AD requires revising the maintenance or inspection program to incorporate certain maintenance requirements and airworthiness limitations. The unsafe condition is fatigue damage in principal structural elements, which could result in reduced structural integrity of the airplane. You may examine the MCAI in the AD docket on the internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2018– 0364. Comments We gave the public the opportunity to participate in developing this final rule. The following presents the comments received on the NPRM and the FAA’s response to each comment. Request To Remove Duplicated Language Airbus asked that we remove the duplicated language in the Discussion section of the NPRM which repeats the phrase ‘‘compiling all ALS Part 1.’’ We agree that the specified language in the Discussion section was duplicated, and have removed this duplication accordingly. Request To Release Related ADs at the Same Time Airbus requested in docket numbers, FAA–2018–0390 and FAA–2018–0365 that we release this final rule and the following related ADs at the same time to provide clarity to operators. All four pending ADs are related to the same removal of 15 nose landing gear parts from ALS Part 1, on different airplane models. PO 00000 Frm 00031 Fmt 4700 Sfmt 4700 47057 • Docket No. FAA–2018–0390, Product Identifier 2017–NM–130–AD (EASA AD 2017–0145, dated August 31, 2017). • Docket No. FAA–2018–0365, Product Identifier 2017–NM–155–AD (EASA AD 2017–0203, dated October 12, 2017). • Docket No. FAA–2018–0396, Product Identifier 2017–NM–156–AD (EASA AD 2017–0202, dated October 12, 2017). We agree with the request insofar as we can control the publication schedule. While we cannot ensure that all four will be published on the same date, we will coordinate with the Office of the Federal Register (OFR) and attempt to issue all four final rules at the same time. Conclusion We reviewed the relevant data, considered the comments received, and determined that air safety and the public interest require adopting this final rule as proposed, except for minor editorial changes. We have determined that these minor changes: • Are consistent with the intent that was proposed in the NPRM for addressing the unsafe condition; and • Do not add any additional burden upon the public than was already proposed in the NPRM. Related Service Information Under 1 CFR Part 51 Airbus SAS has issued the following service information, which describes procedures for revising the maintenance or inspection program to incorporate new or more restrictive maintenance requirements and airworthiness limitations. These documents are distinct since they apply to different airplane models. • For Model A300 series airplanes: Section 4, ‘‘Life Limits (LL)/ Demonstrated Fatigue Lives (DF),’’ of Part 1, ‘‘Safe Life Airworthiness Limitation Items (SL—ALI),’’ Revision 02, dated August 28, 2017, of the Airbus Model A300 Airworthiness Limitations Section (ALS). • For Model A300 B4–600, B4–600R, and F4–600R series airplanes, and Model A300 C4–605R Variant F airplanes (collectively called Model A300–600 series airplanes): Section 4, ‘‘Life Limits (LL)/Demonstrated Fatigue Lives (DF),’’ of Part 1, ‘‘Safe Life Airworthiness Limitation Items (SL— ALI),’’ Revision 02, dated August 28, 2017, of the Airbus Model A300–600 Airworthiness Limitations Section (ALS). • For Model A310 series airplanes: Section 4, ‘‘Life Limits (LL)/ E:\FR\FM\18SER1.SGM 18SER1 47058 Federal Register / Vol. 83, No. 181 / Tuesday, September 18, 2018 / Rules and Regulations Demonstrated Fatigue Lives (DF),’’ of Part 1, ‘‘Safe Life Airworthiness Limitation Items (SL—ALI),’’ Revision 02, dated August 28, 2017, of the Airbus Model A310 Airworthiness Limitations Section (ALS). This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section. daltland on DSKBBV9HB2PROD with RULES Costs of Compliance We estimate that this AD affects 132 airplanes of U.S. registry. We estimate the following costs to comply with this AD: We have determined that revising the maintenance or inspection program takes an average of 90 work-hours per operator, although we recognize that this number may vary from operator to operator. In the past, we have estimated that this action takes 1 work-hour per airplane. Since operators incorporate maintenance or inspection program changes for their affected fleet(s), we have determined that a per-operator estimate is more accurate than a perairplane estimate. Therefore, we estimate the total cost per operator to be $7,650 (90 work-hours × $85 per workhour). Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. This AD is issued in accordance with authority delegated by the Executive Director, Aircraft Certification Service, as authorized by FAA Order 8000.51C. In accordance with that order, issuance of ADs is normally a function of the Compliance and Airworthiness Division, but during this transition period, the Executive Director has delegated the authority to issue ADs applicable to transport category VerDate Sep<11>2014 16:42 Sep 17, 2018 Jkt 244001 airplanes and associated appliances to the Director of the System Oversight Division. Regulatory Findings This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), (3) Will not affect intrastate aviation in Alaska, and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ 2018–18–19 Airbus SAS: Amendment 39– 19398; Docket No. FAA–2018–0364; Product Identifier 2017–NM–154–AD. (a) Effective Date This AD is effective October 23, 2018. (b) Affected ADs This AD affects AD 2015–22–05, Amendment 39–18310 (80 FR 69846, November 12, 2015) (‘‘AD 2015–22–05’’). (c) Applicability This AD applies to Airbus SAS Model A300 B2–1A, B2–1C, B2K–3C, B2–203, B4– 2C, B4–103, and B4–203 airplanes; Model A300 B4–601, B4–603, B4–620, and B4–622 airplanes; Model A300 B4–605R and B4– 622R airplanes; Model A300 F4–605R and PO 00000 Frm 00032 Fmt 4700 Sfmt 4700 F4–622R airplanes; Model A300 C4–605R Variant F airplanes; and Model A310–203, –204, –221, –222, –304, –322, –324, and –325 airplanes; certificated in any category, all manufacturer serial numbers. (d) Subject Air Transport Association (ATA) of America Code 05, Time limits/maintenance checks. (e) Reason This AD was prompted by a determination that new or more restrictive maintenance requirements and airworthiness limitations are necessary. We are issuing this AD to prevent fatigue damage in principal structural elements, which could result in reduced structural integrity of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Maintenance or Inspection Program Revision Within 90 days after the effective date of this AD: Revise the maintenance or inspection program, as applicable, to incorporate the applicable information specified in paragraph (g)(1), (g)(2), or (g)(3) of this AD, as applicable. The initial compliance times for accomplishing the tasks is at the applicable times specified in the applicable information specified in paragraph (g)(1), (g)(2), or (g)(3) of this AD, or within 90 days after the effective date of this AD, whichever occurs later. (1) For Model A300 series airplanes: Section 4, ‘‘Life Limits (LL)/Demonstrated Fatigue Lives (DF),’’ of Part 1, ‘‘Safe Life Airworthiness Limitation Items (SL—ALI),’’ Revision 02, dated August 28, 2017, of the Airbus A300 Airworthiness Limitations Section (ALS). (2) For Model A300 B4–600, B4–600R, and F4–600R series airplanes, and Model A300 C4–605R Variant F airplanes (collectively called Model A300–600 series airplanes): Section 4, ‘‘Life Limits (LL)/Demonstrated Fatigue Lives (DF),’’ of Part 1, ‘‘Safe Life Airworthiness Limitation Items (SL—ALI),’’ Revision 02, dated August 28, 2017, of the Airbus A300–600 Airworthiness Limitations Section (ALS). (3) For Model A310 series airplanes: Section 4, ‘‘Life Limits (LL)/Demonstrated Fatigue Lives (DF),’’ of Part 1, ‘‘Safe Life Airworthiness Limitation Items (SL—ALI),’’ Revision 02, dated August 28, 2017, of the Airbus A310 Airworthiness Limitations Section (ALS). (h) No Alternative Actions or Intervals After accomplishment of the revision required by paragraph (g) of this AD, no alternative actions (e.g., inspections) or intervals may be used unless the actions or intervals are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (j)(1) of this AD. (i) Terminating Action Accomplishing the actions required by paragraph (g) of this AD terminates all requirements of AD 2015–22–05. E:\FR\FM\18SER1.SGM 18SER1 daltland on DSKBBV9HB2PROD with RULES Federal Register / Vol. 83, No. 181 / Tuesday, September 18, 2018 / Rules and Regulations (j) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (k)(2) of this AD. Information may be emailed to: 9-ANM-116-AMOCREQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or the European Aviation Safety Agency (EASA); or Airbus SAS’s EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOAauthorized signature. No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 51; email account.airworth-eas@ airbus.com; internet https://www.airbus.com. (4) You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https:// www.archives.gov/federal-register/cfr/ibrlocations.html. (k) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD 2017–0204, dated October 12, 2017, for related information. This MCAI may be found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2018–0364. (2) For more information about this AD, contact Dan Rodina, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206– 231–3225. [Docket No.: FAA–2018–0838; Amdt. No. 91–352] (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) Part 1, ‘‘Safe Life Airworthiness Limitation Items (SL—ALI),’’ Revision 02, dated August 28, 2017, of the Airbus Model A300 Airworthiness Limitations Section (ALS). (ii) Part 1, ‘‘Safe Life Airworthiness Limitation Items (SL—ALI),’’ Revision 02, dated August 28, 2017, of the Airbus Model A300–600 Airworthiness Limitations Section (ALS). (iii) Part 1, ‘‘Safe Life Airworthiness Limitation Items (SL—ALI),’’ Revision 02, dated August 28, 2017, of the Airbus Model A310 Airworthiness Limitations Section (ALS). (3) For service information identified in this AD, contact Airbus SAS, Airworthiness Office—EAW, Rond-Point Emile Dewoitine VerDate Sep<11>2014 16:42 Sep 17, 2018 Jkt 244001 Issued in Des Moines, Washington, on August 30, 2018. Jeffrey E. Duven, Director, System Oversight Division, Aircraft Certification Service. [FR Doc. 2018–19858 Filed 9–17–18; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 91 RIN 2120–AL34 Amendment of the Prohibition Against Certain Flights in the Pyongyang Flight Information Region (FIR) (ZKKP) Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. AGENCY: This action amends the prohibition against certain flight operations in the Pyongyang Flight Information Region (FIR) (ZKKP) by all: U.S. air carriers; U.S. commercial operators; persons exercising the privileges of an airman certificate issued by the FAA, except when such persons are operating U.S.-registered aircraft for a foreign air carrier; and operators of U.S.-registered civil aircraft, except where the operator of such aircraft is a foreign air carrier. The FAA is also providing an approval process and exemption information for this Special Federal Aviation Regulations (SFAR), consistent with the approval process and exemption information for more recently published flight prohibition SFARs. This final rule will remain in effect for 2 years. DATES: This final rule is effective on September 18, 2018. FOR FURTHER INFORMATION CONTACT: Michael Filippell, Air Transportation SUMMARY: PO 00000 Frm 00033 Fmt 4700 Sfmt 4700 47059 Division, Flight Standards Service, Federal Aviation Administration, 800 Independence Avenue SW, Washington, DC 20591; telephone 202–267–8166; email michael.e.filippell@faa.gov. SUPPLEMENTARY INFORMATION: I. Executive Summary This action amends the prohibition of flight operations in the Pyongyang FIR (ZKKP) 1 by all: U.S. air carriers; U.S. commercial operators; persons exercising the privileges of an airman certificate issued by the FAA, except when such persons are operating U.S.registered aircraft for a foreign air carrier; and operators of U.S.-registered civil aircraft, except where the operator of such aircraft is a foreign air carrier. From February 17, 1998, until November 3, 2017, the FAA prohibited U.S. civil aviation operations in the Pyongyang FIR (ZKKP) west of 132 degrees east longitude under SFAR No. 79 due to the hazardous situation created by North Korea’s military capabilities and its rules of engagement. On November 3, 2017, the FAA issued KICZ Notice to Airmen (NOTAM) A0023/17, prohibiting U.S. civil aviation operations in the entire Pyongyang FIR (ZKKP) due to the hazardous situation created by North Korean military capabilities and activities, including unannounced North Korean missile launches and air defense weapons systems. This amendment to SFAR No. 79 incorporates the November 3, 2017 NOTAM’s expanded flight prohibition into the Code of Federal Regulations (CFR). The FAA finds this action necessary due to continued hazards to U.S. civil aviation operations in the entire Pyongyang FIR (ZKKP). Further, this action moves SFAR No. 79 into subpart M, Special Federal Aviation Regulations, of part 91 and adds an expiration date, consistent with other flight prohibition SFARs. The FAA also is providing an approval process and exemption information for SFAR No. 79, 14 CFR 91.1615, consistent with the approval process and exemption information for more recently published flight prohibition SFARs. SFAR No. 79, § 91.1615, will expire on September 18, 2020. 1 The FAA notes that, prior to this rule, the FAA referred to the Pyongyang FIR (ZKKP) as ‘‘the flight information region of the Democratic People’s Republic of Korea (DPRK)’’ in the title of SFAR No. 79. The FAA has changed that reference in this rule to more accurately represent the FIR name, in accordance with International Civil Aviation Organization (ICAO) naming conventions. The Democratic People’s Republic of Korea (DPRK) is the official name of North Korea. E:\FR\FM\18SER1.SGM 18SER1

Agencies

[Federal Register Volume 83, Number 181 (Tuesday, September 18, 2018)]
[Rules and Regulations]
[Pages 47056-47059]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2018-19858]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0364; Product Identifier 2017-NM-154-AD; Amendment 
39-19398; AD 2018-18-19]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for all 
Airbus SAS Model A300 and A310 series airplanes; and Model A300 B4-600, 
B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F 
airplanes (collectively called Model A300-600 series airplanes). This 
AD was prompted by a determination that new or more restrictive 
maintenance requirements and airworthiness limitations are necessary. 
This AD requires revising the maintenance or inspection program, as 
applicable, to incorporate new or more restrictive maintenance 
requirements and airworthiness limitations. We are issuing this AD to 
address the unsafe condition on these products.

DATES: This AD is effective October 23, 2018.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of October 23, 
2018.

ADDRESSES: For service information identified in this final rule, 
contact Airbus SAS, Airworthiness Office--EAW, Rond-Point Emile 
Dewoitine No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93 36 
96; fax +33 5 61 93 44 51; email [email protected]; 
internet https://www.airbus.com. You may view this service information 
at the FAA, Transport Standards Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0364.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0364; or in person at Docket Operations

[[Page 47057]]

between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this final rule, the regulatory 
evaluation, any comments received, and other information. The address 
for Docket Operations (phone: 800-647-5527) is in the ADDRESSES 
section. Comments will be available in the AD docket shortly after 
receipt.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3225.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to all Airbus SAS Model A300 
and A310 series airplanes; and Model A300 B4-600, B4-600R, and F4-600R 
series airplanes, and Model A300 C4-605R Variant F airplanes 
(collectively called Model A300-600 series airplanes). The NPRM 
published in the Federal Register on May 14, 2018 (83 FR 22219). The 
NPRM was prompted by a determination that new or more restrictive 
maintenance requirements and airworthiness limitations are necessary. 
The NPRM proposed to require revising the maintenance or inspection 
program, as applicable, to incorporate new or more restrictive 
maintenance requirements and airworthiness limitations. We are issuing 
this AD to prevent fatigue damage in principal structural elements, 
which could result in reduced structural integrity of the airplane.
    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Union, has issued EASA AD 
2017-0204, dated October 12, 2017 (referred to after this as the 
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to 
correct an unsafe condition for all Airbus SAS Model A300 and A310 
series airplanes; and Model A300 B4-600, B4-600R, and F4-600R series 
airplanes, and Model A300 C4-605R Variant F airplanes (collectively 
called Model A300-600 series airplanes). The MCAI states:

    The airworthiness limitations for the Airbus A300, A310, A300-
600 and A300-600ST family aeroplanes, which are approved by EASA, 
are currently defined and published in the Airbus A300, A310 and 
A300-600 Airworthiness Limitations Section (ALS) documents. The Safe 
Life Airworthiness Limitation Items are specified in the A300, A310 
and A300-600 (including the A300-600ST) ALS Part 1 documents. These 
instructions have been identified as mandatory for continuing 
airworthiness.
    Failure to accomplish these instructions could result in an 
unsafe condition.
    EASA previously issued AD 2013-0248 [which corresponds to FAA AD 
2015-22-05, Amendment 39-18310 (80 FR 69846, November 12, 2015) 
(``AD 2015-22-05'')] to require the implementation of the 
instructions and airworthiness limitations as specified in Airbus 
A300, A310 and A300-600 ALS Part 1 documents at Revision 01.
    Since that [EASA] AD was issued, improvement of safe life 
component selection and life extension campaigns resulted in life 
limitations changes, among others new or more restrictive life 
limitations, approved by EASA. Consequently, Airbus published 
Revision 02 of the A300, A310 and A300-600 ALS Part 1, compiling all 
ALS Part 1 changes approved since previous Revision 01.
    For the reason described above, this [EASA] AD retains the 
requirements of EASA AD 2013-0248, which is superseded, and requires 
accomplishment of the actions specified in A300 ALS Part 1 Revision 
02, A310 ALS Part 1 Revision 02 and A300-600 ALS Part 1 Revision 02.

    This AD requires revising the maintenance or inspection program to 
incorporate certain maintenance requirements and airworthiness 
limitations. The unsafe condition is fatigue damage in principal 
structural elements, which could result in reduced structural integrity 
of the airplane. You may examine the MCAI in the AD docket on the 
internet at https://www.regulations.gov by searching for and locating 
Docket No. FAA-2018-0364.

Comments

    We gave the public the opportunity to participate in developing 
this final rule. The following presents the comments received on the 
NPRM and the FAA's response to each comment.

Request To Remove Duplicated Language

    Airbus asked that we remove the duplicated language in the 
Discussion section of the NPRM which repeats the phrase ``compiling all 
ALS Part 1.''
    We agree that the specified language in the Discussion section was 
duplicated, and have removed this duplication accordingly.

Request To Release Related ADs at the Same Time

    Airbus requested in docket numbers, FAA-2018-0390 and FAA-2018-0365 
that we release this final rule and the following related ADs at the 
same time to provide clarity to operators. All four pending ADs are 
related to the same removal of 15 nose landing gear parts from ALS Part 
1, on different airplane models.
     Docket No. FAA-2018-0390, Product Identifier 2017-NM-130-
AD (EASA AD 2017-0145, dated August 31, 2017).
     Docket No. FAA-2018-0365, Product Identifier 2017-NM-155-
AD (EASA AD 2017-0203, dated October 12, 2017).
     Docket No. FAA-2018-0396, Product Identifier 2017-NM-156-
AD (EASA AD 2017-0202, dated October 12, 2017).
    We agree with the request insofar as we can control the publication 
schedule. While we cannot ensure that all four will be published on the 
same date, we will coordinate with the Office of the Federal Register 
(OFR) and attempt to issue all four final rules at the same time.

Conclusion

    We reviewed the relevant data, considered the comments received, 
and determined that air safety and the public interest require adopting 
this final rule as proposed, except for minor editorial changes. We 
have determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for addressing the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

    Airbus SAS has issued the following service information, which 
describes procedures for revising the maintenance or inspection program 
to incorporate new or more restrictive maintenance requirements and 
airworthiness limitations. These documents are distinct since they 
apply to different airplane models.
     For Model A300 series airplanes: Section 4, ``Life Limits 
(LL)/Demonstrated Fatigue Lives (DF),'' of Part 1, ``Safe Life 
Airworthiness Limitation Items (SL--ALI),'' Revision 02, dated August 
28, 2017, of the Airbus Model A300 Airworthiness Limitations Section 
(ALS).
     For Model A300 B4-600, B4-600R, and F4-600R series 
airplanes, and Model A300 C4-605R Variant F airplanes (collectively 
called Model A300-600 series airplanes): Section 4, ``Life Limits (LL)/
Demonstrated Fatigue Lives (DF),'' of Part 1, ``Safe Life Airworthiness 
Limitation Items (SL--ALI),'' Revision 02, dated August 28, 2017, of 
the Airbus Model A300-600 Airworthiness Limitations Section (ALS).
     For Model A310 series airplanes: Section 4, ``Life Limits 
(LL)/

[[Page 47058]]

Demonstrated Fatigue Lives (DF),'' of Part 1, ``Safe Life Airworthiness 
Limitation Items (SL--ALI),'' Revision 02, dated August 28, 2017, of 
the Airbus Model A310 Airworthiness Limitations Section (ALS).
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

Costs of Compliance

    We estimate that this AD affects 132 airplanes of U.S. registry.
    We estimate the following costs to comply with this AD:
    We have determined that revising the maintenance or inspection 
program takes an average of 90 work-hours per operator, although we 
recognize that this number may vary from operator to operator. In the 
past, we have estimated that this action takes 1 work-hour per 
airplane. Since operators incorporate maintenance or inspection program 
changes for their affected fleet(s), we have determined that a per-
operator estimate is more accurate than a per-airplane estimate. 
Therefore, we estimate the total cost per operator to be $7,650 (90 
work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to transport category airplanes and 
associated appliances to the Director of the System Oversight Division.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2018-18-19 Airbus SAS: Amendment 39-19398; Docket No. FAA-2018-0364; 
Product Identifier 2017-NM-154-AD.

(a) Effective Date

    This AD is effective October 23, 2018.

(b) Affected ADs

    This AD affects AD 2015-22-05, Amendment 39-18310 (80 FR 69846, 
November 12, 2015) (``AD 2015-22-05'').

(c) Applicability

    This AD applies to Airbus SAS Model A300 B2-1A, B2-1C, B2K-3C, 
B2-203, B4-2C, B4-103, and B4-203 airplanes; Model A300 B4-601, B4-
603, B4-620, and B4-622 airplanes; Model A300 B4-605R and B4-622R 
airplanes; Model A300 F4-605R and F4-622R airplanes; Model A300 C4-
605R Variant F airplanes; and Model A310-203, -204, -221, -222, -
304, -322, -324, and -325 airplanes; certificated in any category, 
all manufacturer serial numbers.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time limits/
maintenance checks.

(e) Reason

    This AD was prompted by a determination that new or more 
restrictive maintenance requirements and airworthiness limitations 
are necessary. We are issuing this AD to prevent fatigue damage in 
principal structural elements, which could result in reduced 
structural integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance or Inspection Program Revision

    Within 90 days after the effective date of this AD: Revise the 
maintenance or inspection program, as applicable, to incorporate the 
applicable information specified in paragraph (g)(1), (g)(2), or 
(g)(3) of this AD, as applicable. The initial compliance times for 
accomplishing the tasks is at the applicable times specified in the 
applicable information specified in paragraph (g)(1), (g)(2), or 
(g)(3) of this AD, or within 90 days after the effective date of 
this AD, whichever occurs later.
    (1) For Model A300 series airplanes: Section 4, ``Life Limits 
(LL)/Demonstrated Fatigue Lives (DF),'' of Part 1, ``Safe Life 
Airworthiness Limitation Items (SL--ALI),'' Revision 02, dated 
August 28, 2017, of the Airbus A300 Airworthiness Limitations 
Section (ALS).
    (2) For Model A300 B4-600, B4-600R, and F4-600R series 
airplanes, and Model A300 C4-605R Variant F airplanes (collectively 
called Model A300-600 series airplanes): Section 4, ``Life Limits 
(LL)/Demonstrated Fatigue Lives (DF),'' of Part 1, ``Safe Life 
Airworthiness Limitation Items (SL--ALI),'' Revision 02, dated 
August 28, 2017, of the Airbus A300-600 Airworthiness Limitations 
Section (ALS).
    (3) For Model A310 series airplanes: Section 4, ``Life Limits 
(LL)/Demonstrated Fatigue Lives (DF),'' of Part 1, ``Safe Life 
Airworthiness Limitation Items (SL--ALI),'' Revision 02, dated 
August 28, 2017, of the Airbus A310 Airworthiness Limitations 
Section (ALS).

(h) No Alternative Actions or Intervals

    After accomplishment of the revision required by paragraph (g) 
of this AD, no alternative actions (e.g., inspections) or intervals 
may be used unless the actions or intervals are approved as an 
alternative method of compliance (AMOC) in accordance with the 
procedures specified in paragraph (j)(1) of this AD.

(i) Terminating Action

    Accomplishing the actions required by paragraph (g) of this AD 
terminates all requirements of AD 2015-22-05.

[[Page 47059]]

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (k)(2) of this AD. Information 
may be emailed to: [email protected]. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or the European Aviation 
Safety Agency (EASA); or Airbus SAS's EASA Design Organization 
Approval (DOA). If approved by the DOA, the approval must include 
the DOA-authorized signature.

(k) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) EASA AD 2017-0204, dated October 12, 2017, for related 
information. This MCAI may be found in the AD docket on the internet 
at https://www.regulations.gov by searching for and locating Docket 
No. FAA-2018-0364.
    (2) For more information about this AD, contact Dan Rodina, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3225.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Part 1, ``Safe Life Airworthiness Limitation Items (SL--
ALI),'' Revision 02, dated August 28, 2017, of the Airbus Model A300 
Airworthiness Limitations Section (ALS).
    (ii) Part 1, ``Safe Life Airworthiness Limitation Items (SL--
ALI),'' Revision 02, dated August 28, 2017, of the Airbus Model 
A300-600 Airworthiness Limitations Section (ALS).
    (iii) Part 1, ``Safe Life Airworthiness Limitation Items (SL--
ALI),'' Revision 02, dated August 28, 2017, of the Airbus Model A310 
Airworthiness Limitations Section (ALS).
    (3) For service information identified in this AD, contact 
Airbus SAS, Airworthiness Office--EAW, Rond-Point Emile Dewoitine 
No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax 
+33 5 61 93 44 51; email [email protected]; internet 
https://www.airbus.com.
    (4) You may view this service information at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 
206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Des Moines, Washington, on August 30, 2018.
Jeffrey E. Duven,
Director, System Oversight Division, Aircraft Certification Service.
[FR Doc. 2018-19858 Filed 9-17-18; 8:45 am]
 BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.