Department of Transportation April 20, 2016 – Federal Register Recent Federal Regulation Documents
Results 1 - 16 of 16
Airworthiness Directives; Pratt & Whitney Division Turbofan Engines
We propose to adopt a new airworthiness directive (AD) for certain Pratt & Whitney (PW) PW4164, PW4164-1D, PW4168, PW4168-1D, PW4168A, PW4168A-1D, and PW4170 turbofan engines. This proposed AD was prompted by several instances of fuel leaks on PW engines installed with the Talon IIB combustion chamber configuration. This proposed AD would require initial and repetitive inspections of the affected fuel nozzles and their replacement with parts eligible for installation. We are proposing this AD to prevent failure of the fuel nozzles, which could lead to engine fire and damage to the airplane.
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all Turbomeca S.A. Arriel 2E turboshaft engines. This AD requires removing the pre-TU 193 adjusted high-pressure/low-pressure pump and metering valve assembly and replacing it with a part that is eligible for installation. This AD also requires replacing the constant delta- pressure (delta-P) diaphragm of the fuel metering valve. This AD was prompted by reports of fuel flow non-conformities found during acceptance tests of Arriel 2E hydro-mechanical metering units (HMUs). We are issuing this AD to prevent failure of the delta-P diaphragm, which could result in an uncommanded in-flight shutdown and damage to the helicopter.
Beyond Compliance Program
The Fixing America's Surface Transportation (FAST) Act requires FMCSA to implement a ``Beyond Compliance'' program no later than 18 months after the enactment of the Act. Through this proposed program, the FMCSA Administrator must allow recognition, either through credit recognized by a new Beyond Compliance Behavior Analysis and Safety Improvement Category (BASIC), or an improved Safety Measurement System (SMS) percentile, for a motor carrier that: (1) Installs advanced safety equipment; (2) uses enhanced driver fitness measures; (3) adopts fleet safety management tools, technologies, and programs; or (4) satisfies other standards determined appropriate by the Administrator. The FAST Act also requires that the Agency provide the opportunity for notice and comment on a process for identifying and reviewing advanced safety equipment, enhanced driver fitness measures, fleet safety management tools, technologies, and programs, and other standards for use by motor carriers to receive recognition. This proposed program will not allow relief from regulatory requirements. This notice satisfies that requirement to seek comments on this program. Comments and data received in response to this notice will be used to further develop the Beyond Compliance program.
Commercial Driver's License: Missouri Department of Revenue (DOR); Application for Exemption
FMCSA announces that it has received an application from the Missouri Department of Revenue (DOR), Driver's License Bureau, for a limited exemption from the Agency's commercial driver's license (CDL) regulations. These regulations require a driver to pass the general knowledge test before being issued a Commercial Learner's Permit (CLP). The Missouri DOR requests an exemption from knowledge test requirement for qualified veterans who participated in dedicated training in approved military programs. The Missouri DOR states that its goal is to assist qualified veterans in obtaining employment when returning to the civilian workforce, and that granting this exemption will assist veterans who have already been through extensive military training. FMCSA requests public comment on the exemption application. In addition, because the issue raised by the Missouri DOR is not unique to that State, FMCSA requests public comment whether the exemption, if granted, should cover all State Driver's Licensing Agencies (SDLAs).
Household Goods Consumer Protection Working Group: Membership Solicitation
FMCSA announces its intent to establish the Household Goods (HHG) Consumer Protection Working Group (Working Group). The Fixing America's Surface Transportation (FAST) Act requires FMCSA to establish this Working Group to provide recommendations on how to better educate and protect HHG moving customers (consumers) during an interstate HHG move. FMCSA solicits applications and nominations of interested persons to serve on the Working Group. As required by the FAST Act, the Working Group must be composed of individuals with expertise in consumer affairs, educators with expertise in how people learn most effectively, and representatives of the interstate HHG moving industry. The FAST Act mandates that the Working Group make its recommendations and the U.S. Department of Transportation (DOT) publish them no later than December 4, 2016.
Hours of Service of Drivers: McKee Foods Transportation LLC, Exemption; FAST Act Extension of Expiration Date
FMCSA announces the extension of the exemption granted to McKee Foods Transportation, LLC, (MFT) on March 27, 2015, for transportation by their team drivers utilizing the sleeper-berth (S/B). The Agency extends the expiration date from March 27, 2015, to March 27, 2020, in response to Section 5206(b)(2)(A) of the ``Fixing America's Surface Transportation Act'' (FAST Act). That section extends the expiration date of hours-of-service (HOS) exemptions in effect on the date of enactment of the FAST Act to 5 years from the date of issuance of the exemptions. The MFT exemption from the Agency's S/B requirement is limited to team drivers employed by MFT to allow these drivers to split S/B time into two periods totaling at least 10 hours, provided neither of the two periods is less than 3 hours in length. The Agency previously determined that the commercial motor vehicle operations of MFT drivers under this exemption would likely achieve a level of safety equivalent to or greater than the level of safety that would be obtained in the absence of the exemption.
Notice of Policy Clarification for Acceptance of Documents With Digital Signatures by the Federal Aviation Administration Aircraft Registry
Notice is hereby given of the FAA's clarification of its policy regarding the acceptance of documents submitted to the FAA Aircraft Registry with digital signatures in support of aircraft registration under 14 CFR 47.13 and conveyances or security documents submitted to the FAA Aircraft Registry regarding claims and interests under 14 CFR 49.13.
Agency Requests for Renewal of a Previously Approved Information Collection(s): Capital Construction Fund and Exhibits
The Maritime Administration (MARAD) invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The collected information is necessary for MARAD to determine an applicant's eligibility to enter into a CCF Agreement. We are required to publish this notice in the Federal Register by the Paperwork Reduction Act of 1995, Public Law 104-13.
Airworthiness Directives; Dassault Aviation Airplanes
We propose to supersede Airworthiness Directive (AD) 2011-10- 01, for all Dassault Aviation Model FALCON 7X airplanes. AD 2011-10-01 currently requires repetitive functional tests of the ram air turbine (RAT) heater and repair if necessary. Since we issued AD 2011-10-01, we received a revision of an airworthiness limitations items (ALI) document, which introduces new and more restrictive maintenance requirements and airworthiness limitations for airplane structures and systems. This proposed AD would require revising the maintenance or inspection program to incorporate new maintenance requirements and airworthiness limitations. We are proposing this AD to prevent reduced structural integrity and reduced control of these airplanes due to the failure of system components.
Airworthiness Directives; Zodiac Seats California LLC Seating Systems
We propose to adopt a new airworthiness directive (AD) for certain Zodiac Seats California LLC seating systems. This proposed AD was prompted by a determination that the affected seating systems may cause serious injury to the occupant during forward impacts when subjected to certain inertia forces. This proposed AD would require removing affected seating systems. We are proposing this AD to prevent serious injury to the occupant during forward impacts in emergency landing conditions.
Airworthiness Directives; Dassault Aviation Airplanes
We propose to adopt a new airworthiness directive (AD) for all Dassault Aviation Model FALCON 900EX and FALCON 2000EX airplanes. This proposed AD was prompted by a review that identified a nonconformity between the torque value applied to the screw-nuts of aileron servo actuators, and the torque value specified by the type design. This proposed AD would require replacing certain aileron servo actuators with serviceable servo actuators. We are proposing this AD to prevent desynchronization between two servo actuator barrels, which could lead to reduced control of the airplane during roll maneuvers at low altitude.
Airworthiness Directives; Bombardier, Inc. Airplanes
We propose to supersede Airworthiness Directive (AD) 2015-02- 23, for certain Bombardier, Inc. Model CL-600-1A11 (CL-600), CL-600- 2A12 (CL-601), and CL-600-2B16 (CL-601-3A, and CL-601-3R Variants) airplanes. AD 2015-02-23 currently requires repetitive inspections for fractured or incorrectly oriented fasteners on the inboard flap hinge- box forward fittings on both wings, and replacement of all fasteners if necessary. The preamble to AD 2015-02-23 explains that we consider the requirements interim action and are considering further rulemaking. We now have determined that further rulemaking is indeed necessary, and that replacement of the fasteners is necessary. This proposed AD would require terminating action to replace the fasteners on the inboard flap hinge-box forward fittings on both wings. We are proposing this AD to detect and correct incorrectly oriented or fractured fasteners, which could result in detachment of the flap hinge-box and the flap surface, and consequent reduced controllability of the airplane.
Airworthiness Directives; BAE SYSTEMS (Operations) Limited Airplanes
We propose to supersede Airworthiness Directive (AD) 2010-10- 13, for all BAE SYSTEMS (Operations) Limited Model BAe 146 and Avro 146 series airplanes. AD 2010-10-13 currently requires repetitive inspections of the wing fixed leading edge and front spar structure for corrosion and cracking, and repair if necessary. Since we issued AD 2010-10-13, the Design Approval Holder (DAH) has issued revised inspection procedures that eliminate a previously approved inspection procedure. This proposed AD would require revised inspection procedures. We are proposing this AD to detect and correct corrosion and cracking of the wing fixed leading edge and front spar structure, which could result in reduced structural integrity of the wing.
Airworthiness Directives; Airbus Airplanes
We propose to supersede Airworthiness Directive (AD) 2005-15- 07, for certain Airbus Model A320-111 airplanes and Model A320-200 series airplanes. AD 2005-15-07 currently requires installing insulator and cable ties to the electrical cables of the S routes at the gaps in the raceway in the wing trailing edge and the wing tip and wing root areas. Since we issued AD 2005-15-07, we have received reports of wire chafing in the left-hand wing trailing edge. This proposed AD would require additional modifications in the trailing edges of both wings. This proposed AD would also remove airplanes from the applicability. We are proposing this AD to prevent wire chafing in the trailing edge of the wings, which could result in a short circuit in the vicinity of the fuel tanks, consequently resulting in a potential source of ignition in a fuel tank vapor space and consequent fuel tank explosion.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
