Department of Transportation July 9, 2014 – Federal Register Recent Federal Regulation Documents
Results 1 - 12 of 12
Environmental Impact Statement: Outagamie and Shawano Counties, Wisconsin
The FHWA is issuing this revised notice to advise the public that FHWA and WisDOT will not prepare a Tier 1 Environmental Impact Statement (EIS) for long-range transportation improvements in the WIS 47 corridor in Outagamie and Shawano Counties, Wisconsin. A Notice of Intent to prepare an EIS was published in the Federal Register on November 18, 2010.
Amendment of Time of Designation for Restricted Area R-3002G; Fort Benning, GA
This action amends the time of designation for restricted area R-3002G at Fort Benning, GA, by removing the words ``local time'' and adding the words ``Eastern time'' to the published time of designation. The majority of the R-3002 complex (i.e., R-3002A through F) lies within the Eastern time zone. However, R-3002G is a small segment that is in the Central time zone. Since the Eastern time zone is predominant and is used for scheduling activities in the entire complex, the time of designation for R-3002G is amended to avoid confusion.
Texas Bus and Limo Acquisition Corp.-Control-GBJ, Inc.; Echo Tours and Charters L.P.; Roadrunner Charters, Inc.; Star Shuttle, Inc.; Tri-City Charters of Bossier, Inc.
Texas Bus and Limo Acquisition Corp. (TBL), GBJ, Inc. (GBJ), Echo Tours and Charters L.P. (Echo), Roadrunner Charters, Inc. (Roadrunner), and Star Shuttle, Inc. (Star) (collectively, Applicants) have filed an application under 49 U.S.C. 14303 for Echo to acquire control of Tri-City Charters of Bossier, Inc. (Tri-City), and for TBL thereafter to acquire control of GBJ, Echo, Roadrunner, and Star. The Board is tentatively approving and authorizing the transaction, and, if no opposing comments are timely filed, this notice will be the final Board action. Persons wishing to oppose the application must follow the rules at 49 CFR 1182.5 and 1182.8.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 747-400 and 747-400F series airplanes. This proposed AD was prompted by reports of cracking in the main equipment center (MEC) drip shield and exhaust plenum. This proposed AD would require installing a fiberglass reinforcing overcoat on the MEC drip shield. We are proposing this AD to prevent water penetration into the MEC, which could result in an electrical short and potential loss of several functions essential for safe flight.
Notice of Intent To Prepare an Environmental Impact Statement for New Medium- and Heavy-Duty Vehicle Fuel Efficiency Improvement Program Standards
NHTSA plans to prepare an Environmental Impact Statement (EIS) to analyze the potential environmental impacts of new fuel efficiency standards for commercial medium- and heavy-duty on-highway vehicles and work trucks (potentially covering engines, chassis, vehicles, and/or trailers manufactured after model year 2018) that will be proposed by the agency pursuant to the Energy Independence and Security Act of 2007. This document initiates the scoping process for determining the scope of issues to be addressed in the EIS and for identifying the significant environmental issues related to the proposed action. Further, it discusses cooperating agencies, the environmental review process, and the agency's tentative planning and decision-making schedule. NHTSA invites the participation of Federal, State, and local agencies, Indian tribes, stakeholders, and the public in this process to help identify the significant issues and reasonable alternatives to be examined in the EIS, and to eliminate from detailed study the issues that are not significant.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for all The Boeing Company Model 767 airplanes. This proposed AD was prompted by a report of a rotary actuator for the trailing edge (TE) flap that had slipped relative to its mating reaction ring, which is attached to the flap support rib. This proposed AD would require repetitive inspections for corrosion of the fixed ring gear and reaction ring splines of the rotary actuator assembly for each support position, and related investigative and corrective actions if necessary. We are proposing this AD to detect and correct reaction ring gears and rotary actuator gears from becoming disengaged with flaps extended and causing an uncommanded roll due to flap blowback, overload, or flap departure from the airplane, which could compromise safe flight and landing of the airplane.
Airworthiness Directives; Piper Aircraft, Inc.
We propose to supersede an existing airworthiness directive (AD) that applies to certain Piper Aircraft, Inc. Models PA-31P airplanes. AD 76-06-09 currently requires repetitive inspection of certain exhaust system parts with replacement of parts mating with the turbocharger, as necessary, and allows installation of a certain tailpipe v-band coupling as terminating action. Since we issued AD 76- 06-09, there have been reports of exhaust system failures, the manufacturer issued new service information, and the tailpipe v-band coupling used for terminating action is obsolete. This proposed AD would require the use of the new service information and expand the scope of the inspections of the turbocharger exhaust system. We are proposing this AD to correct the unsafe condition on these products.
Airworthiness Directives; the Boeing Company Airplanes
We propose to supersede Airworthiness Directive (AD) 2005-14- 07, which applies to certain The Boeing Company Model 727, 727C, 727- 100, 727-100C, 727-200, and 727-200F series airplanes. AD 2005-14-07 currently requires repetitive inspections of the carriage attach fittings on the inboard and outboard foreflaps of each wing for cracking and other discrepancies, and corrective actions if necessary. Since we issued AD 2005-14-07, we received a report of broken inboard and outboard carriage attach fittings of the outboard foreflaps found during an inspection. This proposed AD would reduce certain repetitive inspection intervals for the inboard and outboard carriage attach fittings for the outboard foreflaps, require previously optional terminating actions which install improved outboard foreflap carriage attach fittings, and add new initial and repetitive inspections of those fittings and corrective actions if necessary. We are proposing this AD to detect and correct fatigue cracking of the attach fittings of the foreflap carriage of the wings, which could result in partial or complete loss of the foreflap and consequent loss of controllability of the airplane.
Modification of Class B Airspace; Salt Lake City, UT
This action amends the description of Area C and Area O of the Salt Lake City Class B airspace area by raising the floor of a small portion of Class B airspace between the Salt Lake City Class B surface area and the Hill Air Force Base (AFB) Class D airspace area. This action raises the Class B airspace floor in the northeast corner of Area C from 6,000 feet mean seal level (MSL) to 7,500 feet MSL, and redefines the new boundary segment using the power lines underlying the area. This action enhances the safety and flow of Visual Flight Rules (VFR) aircraft transitioning north and south through the Salt Lake Valley over Interstate 15.
Make Inoperative Exemptions; Vehicle Modifications To Accommodate People With Disabilities; Ejection Mitigation; Lamps, Reflective Devices, and Associated Equipment
This final rule amends NHTSA regulations to include a new exemption relating to the Federal motor vehicle safety standard for ejection mitigation, and to correct a reference regarding the standard for lamps, reflective devices and associated equipment. The exemptions facilitate the mobility of physically disabled drivers and passengers.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
