Department of Transportation March 25, 2014 – Federal Register Recent Federal Regulation Documents
Results 1 - 12 of 12
Reports, Forms, and Recordkeeping Requirements
This document solicits public comments on continuation of the requirements for the collection of information entitled ``Motorcycle Helmet Labeling'' (OMB Control Number: 2127-0518). Before a Federal agency can collect certain information from the public, it must receive approval from the Office of Management and Budget (OMB). Under procedures established by the Paperwork Reduction Act of 1995, before seeking OMB approval, Federal agencies must solicit public comment on proposed collections of information, including extensions and reinstatement of previously approved collections.
Public Availability of Information; Freedom of Information Act
The U.S. Department of Transportation (DOT) is revising its regulations implementing the Freedom of Information Act (FOIA) following a period of public comment on its proposed rule. The purposes for the revision are to update the regulations to be consistent with amendments to FOIA that were signed into law on December 31, 2007, and October 28, 2009, to revise DOT's fee schedule and other charges, and to make provisions clearer and easier to locate.
Airworthiness Directives; Przedsiebiorstwo Doswiadczalno-Produkcyjne Szybownictwa “PZL-Bielsko” Model SZD-50-3 “Puchacz” Sailplanes
We propose to adopt a new airworthiness directive (AD) for Przedsiebiorstwo Doswiadczalno-Produkcyjne Szybownictwa ``PZL-Bielsko'' Model SZD-50-3 ``Puchacz'' sailplanes that would supersede AD 2004-11- 10. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as fatigue damage of the welded joint between the airbrake torque tube and the airbrake control system lever located inside the fuselage. We are issuing this proposed AD to require actions to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
We propose to supersede Airworthiness Directive (AD) 2005-13- 05, which applies to certain Boeing Model 747-400F series airplanes. AD 2005-13-05 currently requires inspections for cracking of the web, upper chord, and upper chord strap of the upper deck floor beams, and repair of any cracking. AD 2005-13-05 also requires a preventive modification of the upper deck floor beams, and repetitive inspections for cracking after accomplishing the modification. Since we issued AD 2005-13-05, the upper chords of the upper deck floor beams at certain stations have been determined to be structures that are susceptible to widespread fatigue damage, and certain airplanes with an initial modification require a second modification for the airplane to meet its limit of validity (LOV). This proposed AD would require that second modification and repetitive inspections for cracking and repair if necessary. We are proposing this AD to detect and correct fatigue cracking in certain upper chords of the upper deck floor beam, which could result in reduced structural integrity of the airplane and rapid decompression or reduced controllability of the airplane.
Airworthiness Directives; Bombardier, Inc. Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400, -401, and -402 airplanes. This proposed AD was prompted by reports of rudder bearings falling out of the fore rudder hinge bracket during assembly. This proposed AD would require a proof load test and detailed inspections; and installation of a new bearing, reaming, or repair of the bearing if necessary. We are proposing this AD to detect and correct improper bearing installation, which could result in abnormal wear and potential increased freeplay in the rudder system, and resultant airframe vibration, leading to compromise of the flutter margins of the airplane.
Airworthiness Directives; Dassault Aviation Model FALCON 7X Airplanes
We propose to adopt a new airworthiness directive (AD) for all Dassault Aviation Model FALCON 7X airplanes. This proposed AD was prompted by reports that the pintle pins installed on a certain number of airplanes may be incorrectly protected against corrosion. This proposed AD would require replacing certain pintle pins on the left- and right-hand main landing gear (MLG) with a serviceable part. We are proposing this AD to detect and correct pintle pins that have been incorrectly corrosion-protected, which could cause the pintle pins to shear under normal load and lead to the collapse of the MLG during take-off or landing.
Critical Incident Stress Plans
FRA issues this final rule in accordance with a statutory mandate that the Secretary of Transportation (Secretary) require certain major railroads to develop, and submit to the Secretary for approval, critical incident stress plans that provide for appropriate support services to be offered to their employees who are affected by a ``critical incident'' as defined by the Secretary. The final rule contains a definition of the term ``critical incident,'' the elements appropriate for the rail environment to be included in a railroad's critical incident stress plan, the type of employees to be covered by the plan, a requirement that a covered railroad submit its plan to FRA for approval, and a requirement that a railroad adopt and comply with its FRA-approved plan.
Airworthiness Directives; The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-8 and 747-8F series airplanes powered by certain General Electric (GE) engines. This AD requires removing certain defective software and installing new, improved software. This AD was prompted by a determination that the existing electronic engine control (EEC) software logic can prevent stowage of the thrust reversers (TRs) during certain circumstances, which could cause the TRs to move back to the deployed position. We are issuing this AD to prevent in-flight deployment of one or more TRs due to loss of the TR auto restow function, which could result in inadequate climb performance at an altitude insufficient for recovery, and consequent uncontrolled flight into terrain.
Pipeline Safety: Public Workshop on Class Location Methodology
The Pipeline and Hazardous Materials Safety Administration (PHMSA) is holding a public workshop along with the National Association of Pipeline Safety Representatives to present perspectives and seek comment on whether applying the gas pipeline integrity management (IM) requirements beyond high consequence areas would mitigate the need for class location requirements. This event is just one action in support of addressing Section 5(a)(2) of the Pipeline Safety, Regulatory Certainty, and Job Creation Act of 2011 (Pub. L. 112-90).
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
