Department of Transportation May 28, 2013 – Federal Register Recent Federal Regulation Documents

We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 747 airplanes. This proposed AD was prompted by reports of cracking in the forward and aft inner chord of the body station (BS) 2598 bulkhead near the upper corners of the cutout for the horizontal stabilizer rear spar, and cracking in the bulkhead upper and lower web panels near the inner chord to shear deck connection. This proposed AD would require doing repetitive inspections for cracking in the bulkhead splice fitting, frame supports, forward and aft inner chords, and floor support; doing an inspection for cracking in the bulkhead upper web, doubler, and bulkhead lower web; and corrective actions if necessary; for certain airplanes, inspections for cracking in the repaired area of the bulkhead, and corrective actions if necessary; for certain airplanes, support frame modification and support frame inspections, and related investigative and corrective actions, if necessary; for certain airplanes, repetitive support frame post-modification inspections and inspections for cracking in the hinge support, and related investigative and corrective actions if necessary; for certain airplanes, a one-time inspection of the frame web and upper shear deck (floor support) chord aft side for fasteners; and a one-time inspection of the upper forward inner chord, frame support fitting and splice fitting, for the installation of certain fasteners; and related investigative and corrective actions if necessary; for certain airplanes, a one-time inspection of the upper forward inner chord, frame support fitting and splice fitting for the installation of certain fasteners; a one-time inspection for any repair installed on the left and right side of the aft inner chord, and related investigative and corrective actions, if necessary; for certain airplanes, a one-time inspection of the support frame outer chord for cracking, and repair if necessary; and repetitive support frame post-repair inspections, and corrective actions, if necessary. We are proposing this AD to detect and correct fatigue cracking of the BS 2598 bulkhead structure, which could adversely affect the structural integrity of the bulkhead and the horizontal stabilizer support structure and result in loss of controllability of the airplane.

This notice is announcing a public workshop to be held on the concept of ``Integrity Verification Process.'' The Integrity Verification Process shares similar characteristics with fitness for service processes. At this workshop, the Pipeline and Hazardous Materials Safety Administration, the National Association of State Pipeline Safety Representatives and various other stakeholders will present information and seek comment on a proposed Integrity Verification Process that will help address several mandates set forth in Section 23, Maximum Allowable Operating Pressure, of the Pipeline Safety, Regulatory Certainty, and Job Creation Act of 2011.

In accordance with the Paperwork Reduction Act of 1995, FMCSA announces its plan to submit the Information Collection Request (ICR) described below to the Office of Management and Budget (OMB) for review and approval. The purpose of this new ICR is to broadly examine, by the collection of survey data, the issue of driver harassment and determine the extent to which Electronic Onboard Recorders (EOBRs) used to document drivers' hours of service (HOS) could be used by motor carriers or enforcement personnel to harass drivers or monitor driver productivity. The survey will collect information on the extent to which respondents believe that the use of EOBRs may result in coercion of drivers by motor carriers, shippers, receivers, and transportation intermediaries. The proposed surveys for drivers and carriers collect information related to issues of EOBR harassment of drivers by carriers. FMCSA plans to publish a supplemental notice of proposed rulemaking on EOBRs. Prior to the issuance of a final rule, FMCSA will consider the survey results.

These special conditions are issued for the Embraer S.A. Model EMB-550 airplane. This airplane will have a novel or unusual design feature, specifically new control architecture and a full digital flight control system which provides flight envelope protections. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

These special conditions are issued for the Embraer S.A. Model EMB-550 airplane. This airplane will have a novel or unusual design feature associated with landing loads due to the automatic braking system. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

We are revising an earlier proposed airworthiness directive (AD) for Bell Helicopter Textron, Inc. (Bell), Model 214B and B-1 helicopters, which proposed to require inspecting certain pylon support spindle assemblies (spindles) for any corrosion, or a nick, scratch, dent, or crack, and repairing or replacing any unairworthy spindle before further flight. This SNPRM proposes to revise those requirements by updating the cost of compliance, revising the recording requirements, adding a requirement to reduce the retirement life of an installed spindle, and adding Bell Model 214ST to the applicability.

As authorized by 46 U.S.C. 12121, the Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to grant waivers of the U.S.-build requirement of the coastwise laws under certain circumstances. A request for such a waiver has been received by MARAD. The vessel, and a brief description of the proposed service, is listed below.

The FAA proposes to amend certain airworthiness regulations for transport category airplanes based on recommendations from the Aviation Rulemaking Advisory Committee (ARAC). Adopting this proposal would eliminate certain regulatory differences between the airworthiness standards of the FAA and European Aviation Safety Agency (EASA) without affecting current industry design practices. This action would revise the pitch maneuver design loads criteria; revise the gust and turbulence design loads criteria; revise the application of gust loads to engine mounts, high lift devices, and other control surfaces; add a ``round-the-clock'' discrete gust criterion and a multi-axis discrete gust criterion for airplanes equipped with wing-mounted engines; revise the engine torque loads criteria; add an engine failure dynamic load condition; revise the ground gust design loads criteria; revise the criteria used to establish the rough air design speed, and require the establishment of a rough air Mach number.