Department of Transportation June 22, 2011 – Federal Register Recent Federal Regulation Documents
Results 1 - 14 of 14
Environmental Impact Statement; Nueces County, TX
Pursuant to 40 CFR 1508.22 and 43 TAC Sec. 2.5(e)(2), the FHWA and the Texas Department of Transportation (TxDOT) are issuing this notice to advise the public that an environmental impact statement (EIS) will be prepared for the proposed United States (US) Highway 181 Harbor Bridge replacement/State Highway (SH) 286 (Crosstown Expressway) improvement project in Nueces County, Texas. The project and study limits include the US 181 and Beach Avenue interchange on the north and the SH 286 and Morgan Avenue interchange on the south. Areas within the city of Corpus Christi are included in the study area. The project will be developed in compliance with Section 6002 of the Safe, Accountable, Flexible, Efficient Transportation Equity Act: A Legacy for Users (SAFETEA-LU) and the National Environmental Policy Act (NEPA).
Notice of Final Federal Agency Action on Proposed Highway in Illinois
This notice announces actions taken by the FHWA and other Federal agencies that are final within the meaning of 23 U.S.C. 139(l)(1). The actions relate to the proposed Illinois Route 336 (IL 336) highway project, for construction of an access-controlled, four- lane expressway on new right-of-way between the proposed Macomb Bypass in McDonough County, passing through Fulton County to Interstate 474 (I-474) on the west side of Peoria in Peoria County, Illinois. Those actions grant licenses, permits and approvals for the project.
Petition for Exemption From the Vehicle Theft Prevention Standard; Nissan
This document grants in full Nissan North America, Inc.'s, (Nissan) petition for exemption of the Leaf vehicle line in accordance with 49 CFR part 543, Exemption from Vehicle Theft Prevention Standard. This petition is granted because the agency has determined that the antitheft device to be placed on the line as standard equipment is likely to be as effective in reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of the Theft Prevention Standard (49 CFR part 541). Nissan requested confidential treatment of specific information in its petition by letter dated February 4, 2011. The agency addressed Nissan's request for confidential treatment by letter dated April 27, 2011.
Preliminary Theft Data; Motor Vehicle Theft Prevention Standard
This document requests comments on data about passenger motor vehicle thefts that occurred in calendar year (CY) 2009 including theft rates for existing passenger motor vehicle lines manufactured in model year (MY) 2009. The preliminary theft data indicate that the vehicle theft rate for CY/MY 2009 vehicles (1.33 thefts per thousand vehicles) decreased by 21.3 percent from the theft rate for CY/MY 2008 vehicles (1.69 thefts per thousand vehicles). Publication of these data fulfills NHTSA's statutory obligation to periodically obtain accurate and timely theft data, and publish the information for review and comment.
Airworthiness Directives; Piper Aircraft, Inc. Models PA-24, PA-24-250, and PA-24-260 Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD would require either replacement of the stabilator horn assembly or repetitive inspection of the stabilator horn assembly for corrosion or cracks with replacement of the stabilator horn assembly if any corrosion or cracks are found. This proposed AD was prompted by reports of cracks developing in the stabilator horn assembly. We are proposing this AD to detect and correct corrosion or cracks in the stabilator horn assembly. Corrosion or cracks could lead to failure of the stabilator horn. Consequently, failure of the stabilator horn could lead to a loss of pitch control in flight.
Value Engineering
This notice proposes updated regulations to enhance the integration of value engineering (VE) analysis in the planning and development of highway improvement projects. The intent of these actions is to bring the FHWA's VE regulations up-to-date and consistent with prior changes in legislation and regulations.
Airworthiness Directives; BAE SYSTEMS (OPERATIONS) LIMITED Model BAe 146 and Avro 146-RJ Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Gulfstream Aerospace Corporation Model GV and GV-SP Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD would require inspecting to determine whether a third Halon fire extinguisher bottle is installed in the auxiliary power unit (APU) fragment impact zone, revising the limitations section of the airplane flight manual to add restrictions for APU usage for certain airplanes having a third fire extinguisher bottle, and removing the third fire extinguisher bottle from certain airplanes. This proposed AD was prompted by notification from the airplane manufacturer that the third fire extinguisher bottle is mounted in a small-fragment impact zone. We are proposing this AD to prevent penetration of the bottle by fragments released due to a failure of the APU rotor system. The bottle could rupture and cause substantial damage to primary airframe structure and primary flight controls.
Airworthiness Directives; The Boeing Company Model 747SP Series Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD would require replacing or modifying the upper and lower rudder power control modules (PCM). This proposed AD was prompted by a report of a rudder hard-over event on a Model 747-400 series airplane, caused by a rudder PCM manifold cracking and separating in the area of the yaw damper cavity end-cap. We are proposing this AD to prevent a failure of the lower or upper rudder PCM manifold, which could result in a hard-over of the rudder surface leading to an increase in pilot workload and a possible high-speed runway excursion upon landing.
Airworthiness Directives; Airbus Model A300 Series Airplanes; Model A310 Series Airplanes; and Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes)
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: * * * * * A recent analysis conducted by the manufacturer showed a particular risk for explosive failure of the * * * hydraulic accumulator. This condition, if not detected and corrected, might, for some aeroplane installations, lead to damage to all three hydraulic circuits, possibly resulting in loss of control of the aeroplane or could, for certain other aeroplane installations, lead to an undetected fire in the wheel bay. * * * * * The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.
Modification of Class E Airspace; Newcastle, WY
This action amends Class E airspace at Newcastle, WY, to accommodate aircraft using the Area Navigation (RNAV) Global Positioning System (GPS) standard instrument approach procedures at Mondell Field Airport. This improves the safety and management of Instrument Flight Rules (IFR) operations at the airport. The airport name also is being changed to Mondell Field Airport.
Airworthiness Directives; Dassault Aviation Model FALCON 7X Airplanes
We are superseding an existing airworthiness directive (AD) that applies to the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Establishment of Class E Airspace; Brunswick, ME
This action establishes Class E Airspace at Brunswick, ME, to accommodate the additional airspace needed for the Standard Instrument Approach Procedures developed for Brunswick Executive Airport. This enhances the safety and airspace management of Instrument Flight Rules (IFR) operations at the airport. This action also corrects errors in the legal description published as a proposed rule in the Federal Register on March 18, 2011.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.