Department of Transportation March 2011 – Federal Register Recent Federal Regulation Documents
Results 51 - 100 of 282
Solid Waste Rail Transfer Facilities
The Clean Railroads Act of 2008 amended the law to restrict the jurisdiction of the Surface Transportation Board (Board or STB) over solid waste rail transfer facilities. The Clean Railroads Act also added three new statutory provisions that address the Board's regulation of such facilities, which is now limited to issuance of ``land-use-exemption permits'' in certain circumstances. Upon receiving a land-use-exemption permit issued by the Board, a solid waste rail transfer facility need not comply with State laws, regulations, orders, and other requirements affecting the siting of the facility, except to the extent that the Board requires compliance with any of those requirements. The Clean Railroads Act provides that a solid waste rail transfer facility must comply with all applicable Federal and State requirements respecting the prevention and abatement of pollution, the protection and restoration of the environment, and the protection of public health and safety, in the same manner as any similar solid waste management facility not owned or operated by or on behalf of a rail carrier, except for laws affecting the siting of the facility that are covered by the land-use-exemption permit. As required by the Clean Railroads Act, on January 14, 2009, the Board issued interim rules that were published in the Federal Register on January 27, 2009 (2009 interim rules). Based on the comments received and further evaluation, the Board now modifies the review process for land-use-exemption permits under the Clean Railroads Act and modifies other aspects of the 2009 interim rules, in the interest of clarity and efficiency. The Board requests comments on the modifications contained in the interim rules.
Prohibition Against Certain Flights Within the Tripoli (HLLL) Flight Information Region (FIR)
This action prohibits flight operations within the Tripoli (HLLL) Flight Information Region (FIR) by all U.S. air carriers; U.S. commercial operators; persons exercising the privileges of a U.S. airman certificate, except when such persons are operating a U.S.- registered aircraft for a foreign air carrier; and operators of U.S.- registered civil aircraft, except when such operators are foreign air carriers. The FAA finds this action necessary to prevent a potential hazard to persons and aircraft engaged in such flight operations.
Notice of Policy Regarding Civil Aircraft Operators Providing Contract Support to Government Entities (Public Aircraft Operations)
This notice states the Federal Aviation Administration's (FAA) policy pertaining to civil aircraft operators that provide contract support to government entities.
Reports, Forms and Record Keeping Requirements; Agency Information Collection Activity Under OMB Review
In compliance with the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.), this notice announces that the Information Collection Request (ICR) abstracted below has been forwarded to the Office of Management and Budget (OMB) for review and comment. The ICR describes the nature of the information collections and their expected burden. The Federal Register Notice with a 60-day comment period was published on September 3, 2010 [FR Doc. 2010-22008].
Proposed Amendment of Class E Airspace; Duluth, MN
This action proposes to amend Class E airspace at Duluth, MN, to accommodate new Standard Instrument Approach Procedures at Duluth International Airport. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations at the airport.
Sixteenth Meeting: RTCA Special Committee 205/EUROCAE WG-71: Software Considerations in Aeronautical Systems
The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 205/EUROCAE WG-71: Software Considerations in Aeronautical Systems Agenda for the 16th meeting.
Sixth Meeting: RTCA Special Committee 224: Airport Security Access Control Systems
The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 224: Airport Security Access Control Systems
Application of Air Charter, Inc. D/B/A Air Flamenco for Commuter Authority
The Department of Transportation is directing all interested persons to show cause why it should not issue an order finding Air Charter, Inc. d/b/a Air Flamenco fit, willing, and able, and awarding it Commuter Air Carrier Authorization.
Notice of Final Federal Agency Actions on Proposed Highway in Wisconsin
This notice announces actions taken by FHWA that are final within the meaning of 23 U.S.C. 139(1)(1). The actions relate to a proposed highway project, the WIS 15 Corridor Expansion Project, in the State of Wisconsin. Those actions grant approval for the project. The project will widen the existing two-lane roadway to four travel lanes with a median and construct a northern bypass around the Village of Hortonville, in Outagamie County, Wisconsin. Specific actions include acquiring additional right-of-way, constructing a four-lane bypass, constructing grade separated crossings, constructing a multi-use path, installing new bridges and box culverts, removing and placing fill, removing vegetation, and providing storm water management measures. The project also includes mitigation and restoration actions which are compatible with land use plans.
Consumer Information; Program for Child Restraint Systems; Correction
NHTSA published in the Federal Register of February 25, 2011 a request for comments notice detailing observations from an agency pilot study conducted to determine reasonable conditions for participation in a new consumer information program, as part of the New Car Assessment Program, to help caregivers find a child restraint system (``child safety seat'') that fits their vehicle. This document corrects the public comments submission due date.
Petition for Exemption From the Vehicle Theft Prevention Standard; Ford Motor Company
This document grants in full the Ford Motor Company's (Ford) petition for an exemption of the C-MAX vehicle line in accordance with Sec. 543.9(c)(2) of 49 CFR part 543, Exemption from the Theft Prevention Standard. This petition is granted because the agency has determined that the antitheft device to be placed on the line as standard equipment is likely to be as effective in reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of the Theft Prevention Standard (49 CFR part 541). Ford requested confidential treatment for an attachment it submitted in support of its petition. The agency has addressed Ford's request for confidential treatment by letter dated March 1, 2011.
Moratorium on New Exemptions for Passenger Carrying Operations Conducted for Compensation and Hire in Other Than Standard Category Aircraft
This document announces a temporary moratorium on new requests, or changes to exemptions from certain sections of Title 14, Code of Federal Regulations (14 CFR) for the purpose of carrying passengers for compensation or hire on Living History Flight Experiences (LHFE). It explains the history of these exemptions and the reason for the temporary moratorium.
Reports, Forms, and Recordkeeping Requirements
This notice solicits public comments on continuation of the requirements for the collection of information on safety standards. Before a Federal agency can collect certain information from the public, it must receive approval from the Office of Management and Budget (OMB). Under procedures established by the Paperwork Reduction Act of 1995, before seeking OMB approval, Federal agencies must solicit public comment on proposed collections of information, including extensions and reinstatement of previously approved collections. This document describes a collection of information with respect to the phase-in of the upgraded requirements of Federal Motor Vehicle Safety Standard No. 214, ``Side impact protection,'' for which NHTSA intends to seek OMB approval.
Parts and Accessories Necessary for Safe Operation; Exemption Renewal for Greyhound Lines, Inc.
FMCSA announces its renewal of the exemption for Greyhound Lines, Inc. (Greyhound) regarding the placement of video event recorders at the top of the windshields on its buses. Greyhound will continue to use the video event recorders to increase safety through (1) identification and remediation of risky driving behaviors such as distracted driving and drowsiness; (2) enhanced monitoring of passenger behavior; and (3) enhanced collision review and analysis. The Agency believes that granting this exemption renewal will maintain a level of safety that is equivalent to, or greater than, the level of safety achieved without the exemption. However, the Agency requests comments on this issue, particularly from parties who believe the Greyhound exemption would not meet that standard.
Airworthiness Directives; Airbus Model A330-200 and -300 Series Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: * * * * * The airworthiness limitations applicable to the Safe Life Airworthiness Limitation Items (SL ALI) are given in Airbus A330 ALS Part 1 and A340 ALS Part 1, which are approved by the European Aviation Safety Agency (EASA). The revision 05 of Airbus A340 ALS Part 1 introduces more restrictive maintenance requirements and/or airworthiness limitations. Failure to comply with this revision constitutes an unsafe condition. For A330 aeroplanes, this EASA AD retains the requirements of EASA AD 2010-0131, which it supersedes. For A340 aeroplanes, this EASA AD supersedes EASA AD 2009-0192, and requires the implementation of the new or more restrictive maintenance requirements and/or airworthiness limitations as specified in Airbus A340 ALS Part 1, revision 05.
Airworthiness Directives; Airbus Model A330-200 and -300 Series Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above that would supersede an existing AD. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: * * * * *
Quarterly Rail Cost Adjustment Factor
The Board has approved the second quarter 2011 Rail Cost Adjustment Factor (RCAF) and cost index filed by the Association of American Railroads. The second quarter 2011 RCAF (Unadjusted) is 1.176. The second quarter 2011 RCAF (Adjusted) is 0.523. The second quarter 2011 RCAF-5 is 0.495.
Amendment of Class E Airspace; Pueblo, CO
This action will amend existing Class E airspace at Pueblo Memorial Airport, Pueblo, CO, to facilitate vectoring of Instrument Flight Rules (IFR) traffic from en route airspace to Pueblo Memorial Airport. The FAA is taking this action to enhance the safety and management of aircraft operations at the airport.
Special Conditions: Boeing 747-468, Installation of a Medical Lift
These special conditions are issued for the Boeing 747-468 airplane. This airplane, as modified by Jet Aviation, will have a novel or unusual design feature associated with the installation of a medical lift. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Airworthiness Directives; Airbus Model A310 Series Airplanes, and Airbus Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes)
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER Series Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. For certain airplanes, this proposed AD would require a one-time inspection for damage of the hydraulic actuator rod ends and actuator attach fittings on the thrust reversers, and repair or replacement if necessary. For all airplanes, this proposed AD also would require repetitive inspections for damage of the hydraulic actuator rod ends, attach bolts, and nuts; repetitive inspections for damage of fitting assemblies, wear spacers, and actuator attach fittings on the thrust reverser; repetitive measurements of the wear spacer; and corrective actions if necessary. This proposed AD was prompted by in-service damage of the attachment fittings for the thrust reverser actuator. We are proposing this AD to detect and correct such damage, which could result in actuator attach fitting failure, loss of the thrust reverser auto restow function, and consequent loss of control of the airplane.
Federal Motor Vehicle Safety Standards; Roof Crush Resistance
This document responds to a petition for reconsideration of a final rule that upgraded the agency's safety standard on roof crush resistance. The petition was submitted by the National Truck Equipment Association (NTEA). After carefully considering the petition, we are denying it.
Hours of Service of Railroad Employees; Substantive Regulations for Train Employees Providing Commuter and Intercity Rail Passenger Transportation; Conforming Amendments to Recordkeeping Requirements
FRA is proposing to amend its hours of service recordkeeping regulations, to establish hours of service regulations, including maximum on-duty periods, minimum off-duty periods, and other limitations, for train employees (e.g., locomotive engineers and conductors) providing commuter and intercity rail passenger transportation. The proposed regulations would require that railroads employing such train employees analyze and mitigate the risks for fatigue in the schedules worked by these train employees, and that the railroads submit to FRA for its approval the relevant schedules and fatigue mitigation plans. This proposed rule would also make corresponding changes to FRA's hours of service recordkeeping regulation, to require railroads to keep hours of service records and report excess service to FRA in a manner consistent with the new requirements. This proposed regulation is authorized by the Rail Safety Improvement Act of 2008.
Notice of Rail Energy Transportation Advisory Committee Meeting
Notice is hereby given of a meeting of the Rail Energy Transportation Advisory Committee (RETAC), pursuant to Section 10(a)(2) of the Federal Advisory Committee Act, Public Law 92-463, as amended (5 U.S.C., App. 2).
Airworthiness Directives; Reims Aviation S.A. Model F406 Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; The Boeing Company Model MD-90-30 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires repetitive inspections for cracking of the left and right upper center skin panels of the horizontal stabilizer, and corrective action if necessary. This AD was prompted by a report of a crack found in the upper skin panel at the aft inboard corner of a right horizontal stabilizer. We are issuing this AD to detect and correct cracks in the upper center skin panels of the horizontal stabilizer. Uncorrected cracks might ultimately lead to the loss of overall structural integrity of the horizontal stabilizer.
Airworthiness Directives; Eurocopter France (Eurocopter) Model EC130 B4 Helicopters
This amendment adopts a new airworthiness directive (AD) for Eurocopter Model EC130 B4 helicopters. This action requires identifying and inspecting a certain emergency flotation gear unit ``1G'' (1G unit). This action also requires modification of certain affected 1G units. This amendment is prompted by an uncommanded in-flight deployment of the emergency flotation gear when it was not armed by the crew. The actions specified in this AD are intended to prevent an uncommanded in-flight deployment of the emergency flotation gear, unexpected deceleration and pitch down movement of the helicopter, and subsequent loss of control of the helicopter.
Airworthiness Directives; Airbus Model A310 Series Airplanes, and Airbus Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes)
We are superseding an existing airworthiness directive (AD) that applies to the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes, CL-600-2C10 (Regional Jet Series 700, 701, & 702) Airplanes, CL-600-2D15 (Regional Jet Series 705) Airplanes, and CL-600-2D24 (Regional Jet Series 900) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; B-N Group Ltd. Model BN-2, BN-2A, BN-2A-2, BN-2A-3, BN-2A-6, BN-2A-8, BN-2A-9, BN-2A-20, BN-2A-21, BN-2A-26, BN-2A-27, BN-2B-20, BN-2B-21, BN-2B-26, BN-2B-27, BN-2T, and BN-2T-4R Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. That AD currently requires repetitive detailed inspections of the slat track downstop assemblies to verify that proper hardware is installed, one-time torquing of the nut and bolt, and corrective actions if necessary. This new AD also requires replacing the hardware of the downstop assembly with new hardware of the downstop assembly, doing a detailed inspection or a borescope inspection of the slat cans on each wing and the lower rail of the slat main tracks for debris, replacing the bolts of the aft side guide with new bolts, and removing any debris found in the slat can. This AD also removes airplanes from the applicability. This AD results from reports of parts coming off the main slat track downstop assemblies. We are issuing this AD to prevent loose or missing parts from the main slat track downstop assemblies from falling into the slat can and causing a puncture, which could result in a fuel leak and consequent fire.
Airworthiness Directives; The Boeing Company Model 747 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires measuring the electrical bond resistance between the motor operated valve (MOV) actuators and airplane structure for the main, center, auxiliary, and horizontal stabilizer fuel tanks, as applicable, and corrective action if necessary; revising the maintenance program to incorporate airworthiness limitation (AWL) No. 28-AWL-21 or AWL No. 28-AWL-27, as applicable; and replacing production-installed laminate phenolic spacers with metallic spacers between the fuel jettison MOV and the airplane structure, as applicable. This AD was prompted by fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent electrical current from flowing through an MOV actuator into a fuel tank, which could create a potential ignition source inside the fuel tank. This condition, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Reports, Forms and Recordkeeping Requirements Information Collection Activity Under OMB Review
In compliance with the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.), this notice announces that the Information Collection abstracted below has been forwarded to the Office of Management and Budget (OMB) for review and approval. The nature of the information collection is described as well as its expected burden. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on December 15, 2010. No comments were received.
Organization and Delegation of Powers and Duties; Assistant Secretary for Administration
This rule delegates authorities vested in the Secretary of Transportation (Secretary) by the Energy Independence and Security Act of 2007 (Act) (Pub. L. 110-140; December 19, 2007) to the Assistant Secretary for Administration.
Airworthiness Directives; Goodrich Evacuation Systems Approved Under Technical Standard Order (TSO) TSO-C69b and Installed on Airbus Model A330-200 and -300 Series Airplanes, Model A340-200 and -300 Series Airplanes, and Model A340-541 and -642 Airplanes
We propose to supersede an existing airworthiness directive (AD) that applies to Goodrich evacuation systems approved under TSO- C69b and installed on certain Model A330-200 and -300 series airplanes, Model A340-200 and -300 series airplanes, and Model A340-541 and -642 airplanes. The existing AD currently requires inspecting to determine the part number of the pressure relief valves on the affected Goodrich evacuation systems, and corrective action if necessary. Since we issued that AD, we have received reports that during workshop testing, certain pressure relief valves, which were required by the existing AD, did not seal and allowed the pressure in slides/rafts to fall below the minimum raft mode pressure for the unit. This proposed AD would require inspecting to determine the part number of the pressure relief valves on the affected Goodrich evacuation systems and replacing certain pressure relief valves. This proposed AD would also add airplanes to the applicability. We are proposing this AD to prevent loss of pressure in the escape slides/rafts after an emergency evacuation, which could result in inadequate buoyancy to support the raft's passenger capacity during ditching and increase the chance for injury to raft passengers.
Operations Specifications; Correction
The FAA is correcting a final rule published on February 10, 2011 (76 FR 7482). In that rule, the FAA amended its regulations to clarify and standardize the rules for applications by foreign air carriers and foreign persons for part 129 operations specifications and establish new standards for amendment, suspension, and termination of those operations specifications. This document corrects errors in the codified text of that document.
Proposed Agency Information Collection Activities; Comment Request
In compliance with the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.), this notice announces that the Information Collection Requirement (ICR) abstracted below is being forwarded to the Office of Management and Budget (OMB) for review and comment. The ICR describes the nature of the information collection and its expected burden. The Federal Register notice with a 60-day comment period soliciting comments on the following collection of information was published on January 13, 2011 (76 FR 2441).
Reports, Forms and Record Keeping Requirements; Agency Information Collection Activity Under OMB Review
In compliance with the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.), this notice announces that the Information Collection Request (ICR) abstracted below has been forwarded to the Office of Management and Budget (OMB) for review and comment. The ICR describes the nature of the information collections and their expected burden. The Federal Register Notice with a 60-day comment period was published on January 3, 2011 (76 FR 210). This document describes a collection of labeling information on five Federal motor vehicle safety standards for which the National Highway Traffic Safety Administration (NHTSA) seeks OMB approval. The labeling requirements include brake fluid warning, glazing labeling, safety belt labeling, and vehicle certification labeling.
Qualification of Drivers; Exemption Applications; Vision
FMCSA announces its decision to renew the exemptions from the vision requirement in the Federal Motor Carrier Safety Regulations for 22 individuals. FMCSA has statutory authority to exempt individuals from the vision requirement if the exemptions granted will not compromise safety. The Agency has concluded that granting these exemption renewals will provide a level of safety that is equivalent to or greater than the level of safety maintained without the exemptions for these commercial motor vehicle (CMV) drivers.
Notice of Proposed Revision to Guidance for the Use of Binding Arbitration Under the Administrative Dispute Resolution Act of 1996
On March 4, 2004, the Federal Motor Carrier Safety Administration (FMCSA) published its Guidance for the use of binding arbitration in Agency civil penalty forfeiture proceedings in which the only issues remaining to be resolved are the amount of the civil penalty owed and the length of time in which to pay it. The Guidance provides that FMCSA use a form of arbitration known as ``Night Baseball,'' under which each party gives to the Arbitrator its proposal for the civil penalty in a sealed envelope. After the Arbitrator makes a written determination as to what he or she believes the civil penalty should be, the envelopes are opened. The Arbitrator then selects the proposed civil penalty that is closer to his or her determination. FMCSA is proposing to revise the Guidance to eliminate the ``Night Baseball'' format, and to replace it with a format in which the Arbitrator determines the final civil penalty and the amount of time in which to pay it.
Qualification of Drivers; Exemption Applications; Vision
FMCSA announces its decision to renew the exemptions from the vision requirement in the Federal Motor Carrier Safety Regulations for 8 individuals. FMCSA has statutory authority to exempt individuals from the vision requirement if the exemptions granted will not compromise safety. The Agency has concluded that granting these exemption renewals will provide a level of safety that is equivalent to or greater than the level of safety maintained without the exemptions for these commercial motor vehicle (CMV) drivers.
Proposed Amendment of Class D and E Airspace; Palmdale, CA
This action proposes to amend Class D airspace and Class E airspace at Palmdale, CA, to accommodate aircraft using Instrument Landing System (ILS) Localizer (LOC) standard instrument approach procedures at Palmdale Regional Airport/USAF Plant 42. This action would enhance the safety and management of aircraft operations at Palmdale Regional Airport/USAF Plant 42. This action would also correct the name of the airport.
RTCA Government/Industry NextGen Advisory Committee
The FAA is issuing this notice to advise the public of the renewal of the RTCA Charter (FAA Order 1110.77T) for two years, effective April 2, 2011. The administrator is the sponsor of the committee. The objective of the advisory committee is to seek solutions to issues and challenges involving air transportation concepts, requirements, operational capabilities, and the associated use of technology and related considerations to aeronautical operations that impact the future Air Traffic Management System. RTCA provides the following two categories of recommendations to the FAA: Broad gauged policy and investment priority recommendations used by FAA when considering policy and program decisions; and minimum performance standards, reports, and guidance documents used by the FAA in regulatory decisions and rulemaking. Government regulatory and procurement practices reference or use RTCA standards (with or without change). The Secretary of Transportation has determined that that information and use of committee are necessary in the public interest in connection with the performance of duties imposed on the FAA by law.
National Emergency Medical Services Advisory Council (NEMSAC); Notice of Federal Advisory Committee Meeting
NHTSA announces a meeting of NEMSAC to be held in the Metropolitan Washington, DC area. This notice announces the date, time and location of the meeting, which will be open to the public. The purpose of NEMSAC is to provide a nationally recognized council of emergency medical services representatives and consumers to provide advice and recommendations regarding Emergency Medical Services (EMS) to the U.S. DOT's NHTSA.
Federal Interagency Committee on Emergency Medical Service (FICEMS) Teleconference Meeting
NHTSA announces a teleconference meeting of the Federal Interagency Committee on Emergency Medical Services (FICEMS) to be held as a stakeholder input call-in session to receive input regarding the current and future role of the Federal government in EMS and options for establishing or designating a Federal lead office for EMS. This notice announces the date and time of the meeting, which will be open to the public, as well as call-in information.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.