Department of Transportation August 25, 2010 – Federal Register Recent Federal Regulation Documents

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: Several cases of aileron terminal quadrant support brackets that were manufactured using sheet metal have been found cracked on DHC-8 Series 300 aircraft. Investigation revealed that the failure of the support bracket was due to fatigue. Failure of the aileron terminal quadrant support bracket could result in an adverse reduction of aircraft roll control. These conditions could result in loss of control of the airplane. The proposed AD would require actions

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

In accordance with the procedures governing the application for, and the processing of, special permits from the Department of Transportation's Hazardous Material Regulations (49 CFR Part 107, Subpart B), notice is hereby given that the Office of Hazardous Materials Safety has received the application described herein. Each mode of transportation for which a particular special permit is requested is indicated by a number in the ``Nature of Application'' portion of the table below as follows: 1Motor vehicle, 2Rail freight, 3Cargo vessel, 4Cargo aircraft only, 5Passenger-carrying aircraft.

In accordance with the procedures governing the application for, and the processing of, special permits from the Department of Transportation's Hazardous Material Regulations (49 CFR Part 107, Subpart B), notice is hereby given of the actions on special permits applications in (January to June 2010). The mode of transportation involved are identified by a number in the ``Nature of Application'' portion of the table below as follows: 1Motor vehicle, 2Rail freight, 3Cargo vessel, 4Cargo aircraft only, 5Passenger-carrying aircraft. Application numbers prefixed by the letters EE represent applications for Emergency Special Permits. It should be noted that some of the sections cited were those in effect at the time certain special permits were issued.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA is superseding an existing airworthiness directive (AD) that applies to all Model 737-600, -700, -700C, -800, -900, and - 900ER series airplanes. The existing AD currently requires, for certain airplanes, a one-time detailed inspection of the inboard and outboard aft attach lugs of the left and right elevator tab control mechanisms for discrepancies, and replacement of any discrepant elevator tab control mechanism. For certain other airplanes, the existing AD requires that the inspections be done repetitively. Replacing the elevator tab control mechanism with a new Boeing-built mechanism terminates the repetitive inspections in the existing AD. This new AD requires that modified repetitive inspections be done on all airplanes, regardless of accomplishment of the terminating action specified in the existing AD. This AD results from reports of failure of the aft attach lugs on the elevator tab control mechanisms, which resulted in severe elevator vibration. This AD also results from reports of gaps in elevator tab control mechanisms and analysis that additional elevator tab control mechanisms might have bearings that will come loose. We are issuing this AD to detect and correct discrepancies in the aft attach lugs of the elevator tab control mechanism, which could result in elevator and tab vibration. Consequent structural failure of the elevator or horizontal stabilizer could result in loss of structural integrity and aircraft control.

We are adopting a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation Model 390 airplanes. This AD requires you to inspect for installation of certain serial number (S/N) starter generators and replace the starter generator if one with an affected serial number is found. This AD results from reports that starter generators with deficient armature insulating materials may have been installed on certain airplanes. We are issuing this AD to detect and replace starter generators with defective armature insulating materials. This condition could result in the loss of operation of one or both starter generators with consequent loss of all non battery electrical power.