Department of Transportation December 11, 2006 – Federal Register Recent Federal Regulation Documents

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as possible undersize rivets in the fuselage roof at STN 180.85, BL 19.67, WL 86.2. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.

We propose to supersede Airworthiness Directive (AD) 72-22-01, which applies to certain Raytheon Aircraft Company (RAC) (The Beech Aircraft Company and BEECH previously held Type Certificate Nos. 3A15, 3A16, 5A3, and A-777) Models 33, 35, 36, 45, and 95 series airplanes. AD 72-22-01 currently requires you to determine if each uplock roller is of the greasible type (one having a drilled and grooved inner race), replace any nongreasible uplock roller (one having a solid inner race) with the greasible type before further flight, install hollow zerk- ended mounting bolts on the uplock rollers, and repetitively lubricate the uplock mechanism. Since we issued AD 72-22-01, there was a recent incident involving a RAC Model 95-B55B (T-42A) airplane where a seizure of the uplock rollers occurred. This malfunction of the uplock rollers is addressed in AD 72-22-01. Thus, the FAA has determined that the actions of AD 72-22-01 should also apply to certain serial numbers of the Model 95-B55B (T-42A) airplanes. Consequently, this proposed AD would retain all the actions of AD 72-22-01, would add those Model 95- B55B (T-42A) airplanes to the applicability of this proposed AD, and would list out the specific serial numbers. We are proposing this AD to decrease the possibility of gear-up landings caused by seizure of the uplock rollers.

This notice announces actions taken by the FHWA and other Federal agencies that are final within the meaning of 23 U.S.C. 139(l)(1). The actions relate to a proposed highway project, U.S. Highway 101 Prunedale Improvement Project between Kilo Posts R146.8 to 161.6 (Post Miles R91.2 to 100.4) north of the City of Salinas in Monterey County, State of California. Those actions grant approvals for the project.

The FAA is adopting a new airworthiness directive (AD) for all EMBRAER Model EMB-135ER and -135KE airplanes and Model EMB-145, -145ER, -145MR, -145MP, and -145EP airplanes. This AD requires inspecting the fuel quantity indication system (FQIS) wire harness and the direct current (DC) fuel pump wire harness to determine if the harnesses are properly attached at their respective attachment points and properly separated from one another, and performing corrective actions if necessary. This AD results from a report that the FQIS wire harness may not be properly attached at its attachment points or properly separated from the DC fuel pump wire harness. We are issuing this AD to prevent chafing between those harnesses or chafing of the harnesses against adjacent airplane structure or components, which could present a potential ignition source that could result in a fire or explosion.

The FAA is adopting a new Airworthiness Directive (AD) for all Columbia Aircraft Manufacturing (previously The Lancair Company) Models LC41-550FG and LC42-550FG airplanes equipped with Kelly Aerospace Thermal Systems Supplemental Type Certificate (STC) SA02260CH, Thermawing Deice System (also known as E-Vade). This AD requires you to deactivate the deice system and install a placard in clear view of the pilot. This AD results from problems with the installation of the Kelly Aerospace Thermal Systems Thermawing Deice System following STC SA02260CH. We are issuing this AD to prevent a short circuit condition at the deice heater connector, which could result in damage to the wings and horizontal stabilizer. This damage could lead to reduced structural integrity of the airplane.