Airworthiness Directives; Bombardier Model DHC-8-102, -103, and -106 Airplanes; and Model DHC-8-200 and DHC-8-300 Series Airplanes, 71492-71494 [E6-20969]

Download as PDF 71492 Proposed Rules Federal Register Vol. 71, No. 237 Monday, December 11, 2006 This section of the FEDERAL REGISTER contains notices to the public of the proposed issuance of rules and regulations. The purpose of these notices is to give interested persons an opportunity to participate in the rule making prior to the adoption of the final rules. DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2006–26558; Directorate Identifier 2006–NM–206–AD] RIN 2120–AA64 Airworthiness Directives; Bombardier Model DHC–8–102, –103, and –106 Airplanes; and Model DHC–8–200 and DHC–8–300 Series Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Notice of proposed rulemaking (NPRM). mstockstill on PROD1PC61 with PROPOSALS AGENCY: SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier Model DHC–8–100 (as described above), DHC–8–200, and DHC–8–300 series airplanes. This proposed AD would require doing a one-time inspection for damage of the electrical cable harness assembly located on the left and right wing root to fuselage aft seal, and repair if necessary; and reworking the fuselage aft seal assembly (left and right) to create a clearance between the electrical cable assemblies and the edge of the fairing panel. This proposed AD results from a report that an airplane encountered an uncommanded propeller feathering during climb, which resulted in an emergency landing. We are proposing this AD to prevent chafing or grounding of the wiring against the aft seal assemblies, which, if not corrected, could interrupt the operation of various systems, including the propeller feather control, alternating current (AC) electrical power, and standby hydraulic power, and result in reduced controllability of the airplane. DATES: We must receive comments on this proposed AD by January 10, 2007. ADDRESSES: Use one of the following addresses to submit comments on this proposed AD. VerDate Aug<31>2005 14:58 Dec 08, 2006 Jkt 211001 • DOT Docket Web site: Go to https:// dms.dot.gov and follow the instructions for sending your comments electronically. • Government-wide rulemaking Web site: Go to https://www.regulations.gov and follow the instructions for sending your comments electronically. • Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, room PL–401, Washington, DC 20590. • Fax: (202) 493–2251. • Hand Delivery: Room PL–401 on the plaza level of the Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. Contact Bombardier, Inc., Bombardier Regional Aircraft Division, 123 Garratt Boulevard, Downsview, Ontario M3K 1Y5, Canada, for service information identified in this proposed AD. FOR FURTHER INFORMATION CONTACT: Douglas Wagner, Aerospace Engineer, Airframe and Propulsion Branch, ANE– 172, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, suite 410, Westbury, New York 11590; telephone (516) 228–7306; fax (516) 794–5531. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to submit any relevant written data, views, or arguments regarding this proposed AD. Send your comments to an address listed in the ADDRESSES section. Include the docket number ‘‘FAA–2006–26558; Directorate Identifier 2006–NM–206–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments. We will post all comments we receive, without change, to https:// dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed AD. Using the search function of that Web site, anyone can find and read the comments in any of our dockets, including the name of the individual who sent the comment (or signed the comment on behalf of an association, PO 00000 Frm 00001 Fmt 4702 Sfmt 4702 business, labor union, etc.). You may review the DOT’s complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477–78), or you may visit https:// dms.dot.gov. Examining the Docket You may examine the AD docket on the Internet at https://dms.dot.gov, or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647–5227) is located on the plaza level of the Nassif Building at the DOT street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after the Docket Management System receives them. Discussion Transport Canada Civil Aviation (TCCA), which is the airworthiness authority for Canada, notified us that an unsafe condition may exist on certain Bombardier Model DHC–8–102, –103, and –106 airplanes, and Model DHC–8– 200 and DHC–8–300 series airplanes. TCCA advises that a Model DHC–8 airplane encountered an uncommanded propeller feathering during climb, which resulted in an emergency landing. Investigation showed that the wing-to-fuselage aft seal assembly had chafed through the wires associated with the auto-feather control system. Chafing or grounding of the wiring against the aft seal assemblies, if not corrected, could interrupt the operation of various systems, including the propeller feather control, alternating current (AC) electrical power, and standby hydraulic power, and result in reduced controllability of the airplane. Relevant Service Information Bombardier has issued Service Bulletin 8–24–83, Revision A, dated August 2, 2005. The service bulletin describes procedures for inspecting for damage of the electrical cable harness assembly located at the left and right wing root to fuselage aft seal, and repair if necessary. The service bulletin also describes procedures for reworking the fuselage aft seal assembly (left and right) to create a clearance between the electrical cable assemblies and the edge of the fairing panel. The rework described in Service Bulletin 8–24–83, Revision A, contains the instructions for E:\FR\FM\11DEP1.SGM 11DEP1 Federal Register / Vol. 71, No. 237 / Monday, December 11, 2006 / Proposed Rules incorporating Bombardier Modification Summary Package 8Y122031, Revision B, dated December 2, 2004. (The technical content of Bombardier Modification Summary Package IS8Q2400005, Revision C, dated January 7, 2005, is equivalent to Modification Summary Package 8Y122031, Revision B.) The rework includes removing a rivet and installing a new rivet, installing new anchor nuts with a clamp, and winding a protective layer of ‘‘spiral wrap’’ around the affected electrical cable assemblies. Accomplishing the actions specified in the service information is intended to adequately address the unsafe condition. TCCA mandated the service information and issued Canadian airworthiness directive CF–2006–15, dated June 14, 2006, to ensure the continued airworthiness of these airplanes in Canada. FAA’s Determination and Requirements of the Proposed AD These airplane models are manufactured in Canada and are type certificated for operation in the United States under the provisions of section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement. Pursuant to this bilateral airworthiness agreement, TCCA has kept the FAA informed of the situation described above. We have examined TCCA’s findings, evaluated all pertinent information, and determined that we need to issue an AD for airplanes of this type design that are certificated for operation in the United States. Therefore, we are proposing this AD, which would require accomplishing the actions specified in the service information described previously. mstockstill on PROD1PC61 with PROPOSALS Clarification of Inspection Terminology Where the TCCA airworthiness directive specifies to ‘‘visually inspect’’ and the service bulletin specifies to ‘‘inspect’’ the electrical cable harness assembly, this proposed AD refers to the inspection as a general visual inspection. We have included the definition for a general visual inspection in a note in the proposed AD. Costs of Compliance This proposed AD would affect about 136 airplanes of U.S. registry. The proposed actions would take about 4 work hours per airplane, at an average labor rate of $80 per work hour. Required parts would cost about $75 per airplane. Based on these figures, the estimated cost of the proposed AD for U.S. operators is $53,720, or $395 per airplane. VerDate Aug<31>2005 14:58 Dec 08, 2006 Jkt 211001 Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that the proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket. See the ADDRESSES section for a location to examine the regulatory evaluation. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: PO 00000 Frm 00002 Fmt 4702 Sfmt 4702 71493 Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The Federal Aviation Administration (FAA) amends § 39.13 by adding the following new airworthiness directive (AD): Bombardier, Inc. (Formerly de Havilland, Inc.): Docket No. FAA–2006–26558; Directorate Identifier 2006–NM–206–AD. Comments Due Date (a) The FAA must receive comments on this AD action by January 10, 2007. Affected ADs (b) None. Applicability (c) This AD applies to Bombardier Model DHC–8–102, –103, and –106 airplanes, and Model DHC–8–200 and DHC–8–300 series airplanes, certificated in any category; serial numbers 003 through 606, inclusive. Unsafe Condition (d) This AD results from a report that an airplane encountered an uncommanded propeller feathering during climb, which resulted in an emergency landing. We are issuing this AD to prevent chafing or grounding of the wiring against the aft seal assemblies, which, if not corrected, could interrupt the operation of various systems, including the propeller feather control, alternating current (AC) electrical power, and standby hydraulic power, and result in reduced controllability of the airplane. Compliance (e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Inspection and Rework (f) Within 6,000 flight hours after the effective date of this AD, do the actions in paragraphs (f)(1) and (f)(2) of this AD. Do all actions in accordance with Bombardier Service Bulletin 8–24–83, Revision A, dated August 2, 2005. The actions in paragraph (f)(1) of this AD must be done before the rework in paragraph (f)(2) of this AD. Note 1: Bombardier Service Bulletin 8–24– 83, Revision A, contains the instructions for incorporating Bombardier Modification Summary Package 8Y122031, Revision B, dated December 2, 2004. (The technical content of Bombardier Modification Summary Package IS8Q2400005, Revision C, dated January 7, 2004, is equivalent to Bombardier Modification Summary Package 8Y122031, Revision B.) (1) Do a general visual inspection for damage of the electrical cable harness assembly located on the left and right wing root-to-fuselage aft seal. If any damage is found, repair the damage before further flight. (2) Rework the fuselage aft seal assembly (left and right) to create a clearance between the electrical cable assemblies and the edge of the fairing panel. Note 2: For the purposes of this AD, a general visual inspection is: ‘‘A visual E:\FR\FM\11DEP1.SGM 11DEP1 71494 Federal Register / Vol. 71, No. 237 / Monday, December 11, 2006 / Proposed Rules examination of an interior or exterior area, installation, or assembly to detect obvious damage, failure, or irregularity. This level of inspection is made from within touching distance unless otherwise specified. A mirror may be necessary to ensure visual access to all surfaces in the inspection area. This level of inspection is made under normally available lighting conditions such as daylight, hangar lighting, flashlight, or droplight and may require removal or opening of access panels or doors. Stands, ladders, or platforms may be required to gain proximity to the area being checked.’’ Actions Accomplished in Accordance With Previous Revision of Service Bulletin (g) Actions done before the effective date of this AD in accordance with Bombardier Service Bulletin 8–24–83, dated December 23, 2004, are acceptable for compliance with the corresponding requirements in paragraph (f) of this AD. Alternative Methods of Compliance (AMOCs) (h)(1) The Manager, New York Aircraft Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19. (2) Before using any AMOC approved in accordance with § 39.19 on any airplane to which the AMOC applies, notify the appropriate principal inspector in the FAA Flight Standards Certificate Holding District Office. Related Information (i) Canadian airworthiness directive CF– 2006–15, dated June 14, 2006, also addresses the subject of this AD. Issued in Renton, Washington, on December 1, 2006. Kevin M. Mullin, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E6–20969 Filed 12–8–06; 8:45 am] mstockstill on PROD1PC61 with PROPOSALS BILLING CODE 4910–13–P VerDate Aug<31>2005 14:58 Dec 08, 2006 Jkt 211001 DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2006–26075; Directorate Identifier 2006–CE–55–AD] RIN 2120–AA64 Airworthiness Directives; Raytheon Aircraft Company (The Beech Aircraft Company and BEECH Previously Held Type Certificate Nos. 3A15, 3A16, 5A3, and A–777) Models 35–33, 35–A33, 35– B33, 35–C33, E33, F33, G33, 35–C33A, E33A, F33A, E33C, F33C, 35, A35, B35, C35, D35, E35, F35, G35, H35, J35, K35, M35, N35, P35, S35, V35, V35A, V35B, 36, A36, A45 (T–34A, B45), D45 (T– 34B), 95–55, 95–A55, 95–B55, 95–B55A, 95–B55B (T–42A), 95–C55, 95–C55A, D55, D55A, E55, E55A, 56TC, A56TC, 58, 95, B95, B95A, D95A, and E95 Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Notice of proposed rulemaking (NPRM). AGENCY: SUMMARY: We propose to supersede Airworthiness Directive (AD) 72–22–01, which applies to certain Raytheon Aircraft Company (RAC) (The Beech Aircraft Company and BEECH previously held Type Certificate Nos. 3A15, 3A16, 5A3, and A–777) Models 33, 35, 36, 45, and 95 series airplanes. AD 72–22–01 currently requires you to determine if each uplock roller is of the greasible type (one having a drilled and grooved inner race), replace any nongreasible uplock roller (one having a solid inner race) with the greasible type before further flight, install hollow zerkended mounting bolts on the uplock rollers, and repetitively lubricate the uplock mechanism. Since we issued AD 72–22–01, there was a recent incident involving a RAC Model 95–B55B (T– 42A) airplane where a seizure of the uplock rollers occurred. This malfunction of the uplock rollers is addressed in AD 72–22–01. Thus, the FAA has determined that the actions of AD 72–22–01 should also apply to certain serial numbers of the Model 95– B55B (T–42A) airplanes. Consequently, this proposed AD would retain all the actions of AD 72–22–01, would add those Model 95–B55B (T–42A) airplanes to the applicability of this proposed AD, and would list out the specific serial numbers. We are proposing this AD to decrease the possibility of gear-up landings caused by seizure of the uplock rollers. PO 00000 Frm 00003 Fmt 4702 Sfmt 4702 We must receive comments on this proposed AD by February 9, 2007. ADDRESSES: Use one of the following addresses to comment on this proposed AD: • DOT Docket web site: Go to https:// dms.dot.gov and follow the instructions for sending your comments electronically. • Government-wide rulemaking web site: Go to https://www.regulations.gov and follow the instructions for sending your comments electronically. • Mail: Docket Management Facility; U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL–401, Washington, DC 20590– 0001. • Fax: (202) 493–2251. • Hand Delivery: Room PL–401 on the plaza level of the Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Raytheon Aircraft Company, P.O. Box 85, Wichita, Kansas 67201–0085; telephone: (800) 429–5372 or (316) 676–3140. FOR FURTHER INFORMATION CONTACT: Anthony Flores, Aerospace Engineer, Aerospace Engineer, FAA, Wichita Aircraft Certification Office, 1801 Airport Road, Wichita, Kansas 67209; telephone: (316) 946–4174; facsimile: (316) 946–4107. SUPPLEMENTARY INFORMATION: DATES: Comments Invited We invite you to send any written relevant data, views, or arguments regarding this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include the docket number, ‘‘FAA–2006–26075; Directorate Identifier 2006–CE–55–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments. We will post all comments we receive, without change, to https:// dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive concerning this proposed AD. Discussion Reports of RAC 33, 35, 36, 45, and 95 series airplanes equipped with nongreasible uplock rollers having a solid inner race that renders lubrication of the uplock roller mechanism ineffective E:\FR\FM\11DEP1.SGM 11DEP1

Agencies

[Federal Register Volume 71, Number 237 (Monday, December 11, 2006)]
[Proposed Rules]
[Pages 71492-71494]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: E6-20969]


========================================================================
Proposed Rules
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains notices to the public of 
the proposed issuance of rules and regulations. The purpose of these 
notices is to give interested persons an opportunity to participate in 
the rule making prior to the adoption of the final rules.

========================================================================


Federal Register / Vol. 71, No. 237 / Monday, December 11, 2006 / 
Proposed Rules

[[Page 71492]]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2006-26558; Directorate Identifier 2006-NM-206-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier Model DHC-8-102, -103, and -
106 Airplanes; and Model DHC-8-200 and DHC-8-300 Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Bombardier Model DHC-8-100 (as described above), DHC-8-200, 
and DHC-8-300 series airplanes. This proposed AD would require doing a 
one-time inspection for damage of the electrical cable harness assembly 
located on the left and right wing root to fuselage aft seal, and 
repair if necessary; and reworking the fuselage aft seal assembly (left 
and right) to create a clearance between the electrical cable 
assemblies and the edge of the fairing panel. This proposed AD results 
from a report that an airplane encountered an uncommanded propeller 
feathering during climb, which resulted in an emergency landing. We are 
proposing this AD to prevent chafing or grounding of the wiring against 
the aft seal assemblies, which, if not corrected, could interrupt the 
operation of various systems, including the propeller feather control, 
alternating current (AC) electrical power, and standby hydraulic power, 
and result in reduced controllability of the airplane.

DATES: We must receive comments on this proposed AD by January 10, 
2007.

ADDRESSES: Use one of the following addresses to submit comments on 
this proposed AD.
     DOT Docket Web site: Go to https://dms.dot.gov and follow 
the instructions for sending your comments electronically.
     Government-wide rulemaking Web site: Go to https://
www.regulations.gov and follow the instructions for sending your 
comments electronically.
     Mail: Docket Management Facility, U.S. Department of 
Transportation, 400 Seventh Street, SW., Nassif Building, room PL-401, 
Washington, DC 20590.
     Fax: (202) 493-2251.
     Hand Delivery: Room PL-401 on the plaza level of the 
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    Contact Bombardier, Inc., Bombardier Regional Aircraft Division, 
123 Garratt Boulevard, Downsview, Ontario M3K 1Y5, Canada, for service 
information identified in this proposed AD.

FOR FURTHER INFORMATION CONTACT: Douglas Wagner, Aerospace Engineer, 
Airframe and Propulsion Branch, ANE-172, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, suite 410, Westbury, New 
York 11590; telephone (516) 228-7306; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to submit any relevant written data, views, or 
arguments regarding this proposed AD. Send your comments to an address 
listed in the ADDRESSES section. Include the docket number ``FAA-2006-
26558; Directorate Identifier 2006-NM-206-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of the proposed AD. We will 
consider all comments received by the closing date and may amend the 
proposed AD in light of those comments.
    We will post all comments we receive, without change, to https://
dms.dot.gov, including any personal information you provide. We will 
also post a report summarizing each substantive verbal contact with FAA 
personnel concerning this proposed AD. Using the search function of 
that Web site, anyone can find and read the comments in any of our 
dockets, including the name of the individual who sent the comment (or 
signed the comment on behalf of an association, business, labor union, 
etc.). You may review the DOT's complete Privacy Act Statement in the 
Federal Register published on April 11, 2000 (65 FR 19477-78), or you 
may visit https://dms.dot.gov.

Examining the Docket

    You may examine the AD docket on the Internet at https://
dms.dot.gov, or in person at the Docket Management Facility office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the DOT 
street address stated in the ADDRESSES section. Comments will be 
available in the AD docket shortly after the Docket Management System 
receives them.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the airworthiness 
authority for Canada, notified us that an unsafe condition may exist on 
certain Bombardier Model DHC-8-102, -103, and -106 airplanes, and Model 
DHC-8-200 and DHC-8-300 series airplanes. TCCA advises that a Model 
DHC-8 airplane encountered an uncommanded propeller feathering during 
climb, which resulted in an emergency landing. Investigation showed 
that the wing-to-fuselage aft seal assembly had chafed through the 
wires associated with the auto-feather control system. Chafing or 
grounding of the wiring against the aft seal assemblies, if not 
corrected, could interrupt the operation of various systems, including 
the propeller feather control, alternating current (AC) electrical 
power, and standby hydraulic power, and result in reduced 
controllability of the airplane.

Relevant Service Information

    Bombardier has issued Service Bulletin 8-24-83, Revision A, dated 
August 2, 2005. The service bulletin describes procedures for 
inspecting for damage of the electrical cable harness assembly located 
at the left and right wing root to fuselage aft seal, and repair if 
necessary. The service bulletin also describes procedures for reworking 
the fuselage aft seal assembly (left and right) to create a clearance 
between the electrical cable assemblies and the edge of the fairing 
panel. The rework described in Service Bulletin 8-24-83, Revision A, 
contains the instructions for

[[Page 71493]]

incorporating Bombardier Modification Summary Package 8Y122031, 
Revision B, dated December 2, 2004. (The technical content of 
Bombardier Modification Summary Package IS8Q2400005, Revision C, dated 
January 7, 2005, is equivalent to Modification Summary Package 
8Y122031, Revision B.) The rework includes removing a rivet and 
installing a new rivet, installing new anchor nuts with a clamp, and 
winding a protective layer of ``spiral wrap'' around the affected 
electrical cable assemblies. Accomplishing the actions specified in the 
service information is intended to adequately address the unsafe 
condition. TCCA mandated the service information and issued Canadian 
airworthiness directive CF-2006-15, dated June 14, 2006, to ensure the 
continued airworthiness of these airplanes in Canada.

FAA's Determination and Requirements of the Proposed AD

    These airplane models are manufactured in Canada and are type 
certificated for operation in the United States under the provisions of 
section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and 
the applicable bilateral airworthiness agreement. Pursuant to this 
bilateral airworthiness agreement, TCCA has kept the FAA informed of 
the situation described above. We have examined TCCA's findings, 
evaluated all pertinent information, and determined that we need to 
issue an AD for airplanes of this type design that are certificated for 
operation in the United States.
    Therefore, we are proposing this AD, which would require 
accomplishing the actions specified in the service information 
described previously.

Clarification of Inspection Terminology

    Where the TCCA airworthiness directive specifies to ``visually 
inspect'' and the service bulletin specifies to ``inspect'' the 
electrical cable harness assembly, this proposed AD refers to the 
inspection as a general visual inspection. We have included the 
definition for a general visual inspection in a note in the proposed 
AD.

Costs of Compliance

    This proposed AD would affect about 136 airplanes of U.S. registry. 
The proposed actions would take about 4 work hours per airplane, at an 
average labor rate of $80 per work hour. Required parts would cost 
about $75 per airplane. Based on these figures, the estimated cost of 
the proposed AD for U.S. operators is $53,720, or $395 per airplane.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket. See the 
ADDRESSES section for a location to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The Federal Aviation Administration (FAA) amends Sec.  39.13 by 
adding the following new airworthiness directive (AD):

Bombardier, Inc. (Formerly de Havilland, Inc.): Docket No. FAA-2006-
26558; Directorate Identifier 2006-NM-206-AD.

Comments Due Date

    (a) The FAA must receive comments on this AD action by January 
10, 2007.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Bombardier Model DHC-8-102, -103, and -
106 airplanes, and Model DHC-8-200 and DHC-8-300 series airplanes, 
certificated in any category; serial numbers 003 through 606, 
inclusive.

Unsafe Condition

    (d) This AD results from a report that an airplane encountered 
an uncommanded propeller feathering during climb, which resulted in 
an emergency landing. We are issuing this AD to prevent chafing or 
grounding of the wiring against the aft seal assemblies, which, if 
not corrected, could interrupt the operation of various systems, 
including the propeller feather control, alternating current (AC) 
electrical power, and standby hydraulic power, and result in reduced 
controllability of the airplane.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Inspection and Rework

    (f) Within 6,000 flight hours after the effective date of this 
AD, do the actions in paragraphs (f)(1) and (f)(2) of this AD. Do 
all actions in accordance with Bombardier Service Bulletin 8-24-83, 
Revision A, dated August 2, 2005. The actions in paragraph (f)(1) of 
this AD must be done before the rework in paragraph (f)(2) of this 
AD.

    Note 1: Bombardier Service Bulletin 8-24-83, Revision A, 
contains the instructions for incorporating Bombardier Modification 
Summary Package 8Y122031, Revision B, dated December 2, 2004. (The 
technical content of Bombardier Modification Summary Package 
IS8Q2400005, Revision C, dated January 7, 2004, is equivalent to 
Bombardier Modification Summary Package 8Y122031, Revision B.)

    (1) Do a general visual inspection for damage of the electrical 
cable harness assembly located on the left and right wing root-to-
fuselage aft seal. If any damage is found, repair the damage before 
further flight.
    (2) Rework the fuselage aft seal assembly (left and right) to 
create a clearance between the electrical cable assemblies and the 
edge of the fairing panel.

    Note 2: For the purposes of this AD, a general visual inspection 
is: ``A visual

[[Page 71494]]

examination of an interior or exterior area, installation, or 
assembly to detect obvious damage, failure, or irregularity. This 
level of inspection is made from within touching distance unless 
otherwise specified. A mirror may be necessary to ensure visual 
access to all surfaces in the inspection area. This level of 
inspection is made under normally available lighting conditions such 
as daylight, hangar lighting, flashlight, or droplight and may 
require removal or opening of access panels or doors. Stands, 
ladders, or platforms may be required to gain proximity to the area 
being checked.''

Actions Accomplished in Accordance With Previous Revision of Service 
Bulletin

    (g) Actions done before the effective date of this AD in 
accordance with Bombardier Service Bulletin 8-24-83, dated December 
23, 2004, are acceptable for compliance with the corresponding 
requirements in paragraph (f) of this AD.

Alternative Methods of Compliance (AMOCs)

    (h)(1) The Manager, New York Aircraft Certification Office, FAA, 
has the authority to approve AMOCs for this AD, if requested in 
accordance with the procedures found in 14 CFR 39.19.
    (2) Before using any AMOC approved in accordance with Sec.  
39.19 on any airplane to which the AMOC applies, notify the 
appropriate principal inspector in the FAA Flight Standards 
Certificate Holding District Office.

Related Information

    (i) Canadian airworthiness directive CF-2006-15, dated June 14, 
2006, also addresses the subject of this AD.


    Issued in Renton, Washington, on December 1, 2006.
Kevin M. Mullin,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
 [FR Doc. E6-20969 Filed 12-8-06; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.