Airworthiness Directives; Pacific Aerospace Corporation Ltd Model 750XL Airplanes, 71499-71500 [E6-20976]

Download as PDF Federal Register / Vol. 71, No. 237 / Monday, December 11, 2006 / Proposed Rules are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120–0056. Related Information (g) Refer to Federal Office of Civil Aviation (FOCA) AD HB–2006–444, dated November 7, 2006; Pilatus Aircraft Limited Service Bulletin No.: 25–032, dated October 2, 2006; and DeCrane Aircraft Mandatory Service Bulletin SB05147 Revision B, dated June 26, 2006, for related information. Issued in Kansas City, Missouri, on December 4, 2006. John R. Colomy, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E6–20971 Filed 12–8–06; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2006–26285; Directorate Identifier 2006–CE–69–AD] RIN 2120–AA64 Airworthiness Directives; Pacific Aerospace Corporation Ltd Model 750XL Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as possible undersize rivets in the fuselage roof at STN 180.85, BL 19.67, WL 86.2. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI. DATES: We must receive comments on this proposed AD by January 10, 2007. ADDRESSES: You may send comments by any of the following methods: • DOT Docket Web Site: Go to https://dms.dot.gov and follow the mstockstill on PROD1PC61 with PROPOSALS SUMMARY: VerDate Aug<31>2005 14:58 Dec 08, 2006 Jkt 211001 instructions for sending your comments electronically. • Fax: (202) 493–2251. • Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL–401, Washington, DC 20590– 0001. • Hand Delivery: Room PL–401 on the plaza level of the Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. • Federal eRulemaking Portal: https:// www.regulations.gov. Follow the instructions for submitting comments. Examining the AD Docket You may examine the AD docket on the Internet at https://dms.dot.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (telephone (800) 647– 5227) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329–4146; fax: (816) 329–4090. SUPPLEMENTARY INFORMATION: Streamlined Issuance of AD The FAA is implementing a new process for streamlining the issuance of ADs related to MCAI. The streamlined process will allow us to adopt MCAI safety requirements in a more efficient manner and will reduce safety risks to the public. This process continues to follow all FAA AD issuance processes to meet legal, economic, Administrative Procedure Act, and Federal Register requirements. We also continue to meet our technical decision-making responsibilities to identify and correct unsafe conditions on U.S.-certificated products. This proposed AD references the MCAI and related service information that we considered in forming the engineering basis to correct the unsafe condition. The proposed AD contains text copied from the MCAI and for this reason might not follow our plain language principles. Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the PO 00000 Frm 00008 Fmt 4702 Sfmt 4702 71499 section. Include ‘‘Docket No. FAA–2006–26285; Directorate Identifier 2006–CE–69–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD because of those comments. We will post all comments we receive, without change, to https:// dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. ADDRESSES Discussion The Civil Aviation Authority (CAA), which is the aviation authority for New Zealand, has issued CAA AD DCA/ 750XL/8, Drafted: May 9, 2006; Effective Date: August 31, 2006 (referred to after this as ‘‘the MCAI’’), to correct an unsafe condition for the specified products. The MCAI states the finding of the possible installation of undersize rivets in the fuselage roof at STN 180.85, BL 19.67, WL 86.2. The MCAI requires that you inspect the rivets in the fuselage roof at STN 180.85, BL 19.67, WL 86.2, and replace undersize rivets. You may obtain further information by examining the MCAI in the AD docket. Relevant Service Information Pacific Aerospace Corporation Ltd has issued PAC Pacific Aerospace Corporation Mandatory Service Bulletin PACSB/XL/019, Date Issued: April 21, 2006. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI. FAA’s Determination and Requirements of the Proposed AD This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with this State of Design Authority, they have notified us of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all information and determined the unsafe condition exists and is likely to exist or develop on other products of the same type design. Differences Between This Proposed AD and the MCAI or Service Information We have reviewed the MCAI and related service information and, in general, agree with their substance. But E:\FR\FM\11DEP1.SGM 11DEP1 71500 Federal Register / Vol. 71, No. 237 / Monday, December 11, 2006 / Proposed Rules we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information. We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are described in a separate paragraph of the proposed AD. These requirements, if ultimately adopted, will take precedence over the actions copied from the MCAI. mstockstill on PROD1PC61 with PROPOSALS Costs of Compliance Based on the service information, we estimate that this proposed AD would affect about 7 products of U.S. registry. We also estimate that it would take about 16 work-hours per product to comply with the proposed AD. The average labor rate is $80 per work-hour. Required parts would cost about $100 per product. Where the service information lists required parts costs that are covered under warranty, we have assumed that there will be no charge for these costs. As we do not control warranty coverage for affected parties, some parties may incur costs higher than estimated here. Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $9,660, or $1,380 per product. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a VerDate Aug<31>2005 15:03 Dec 08, 2006 Jkt 211001 substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new AD: Pacific Aerospace Corporation Ltd: Docket No. FAA–2006–26285; Directorate Identifier 2006–CE–69–AD. Comments Due Date (a) We must receive comments by January 10, 2007. 86.2, and replace undersize rivets, following PAC Pacific Aerospace Corporation Mandatory Service Bulletin PACSB/XL/019, Date Issued: April 21, 2006. FAA AD Differences Note: This AD differs from the MCAI and/ or service information as follows: No differences. Other FAA AD Provisions (f) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Staff, FAA, ATTN: Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329–4146; fax: (816) 329–4090, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAAapproved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120–0056. Related Information (g) Refer to MCAI Civil Aviation Authority AD DCA/750XL/8, Drafted: May 9, 2006; Effective Date: August 31, 2006; and PAC Pacific Aerospace Corporation Mandatory Service Bulletin PACSB/XL/019, Date Issued: April 21, 2006, for related information. Issued in Kansas City, Missouri, on December 4, 2006. John R. Colomy, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E6–20976 Filed 12–8–06; 8:45 am] BILLING CODE 4910–13–P Affected ADs (b) None. Applicability (c) This AD applies to Model 750XL airplanes, serial numbers 102, 104 through 120, 122, and 125, certificated in any category. Reason (d) The mandatory continuing airworthiness information (MCAI) states the finding of the possible installation of undersize rivets in the fuselage roof at STN 180.85, BL 19.67, WL 86.2. Actions and Compliance (e) Unless already done, within the next 150 hours time-in-service after the effective date of this AD, inspect the rivets in the fuselage roof at STN 180.85, BL 19.67, WL PO 00000 Frm 00009 Fmt 4702 Sfmt 4702 DEPARTMENT OF THE TREASURY Office of Foreign Assets Control 31 CFR Parts 538 and 560 Comment Request Regarding the Effectiveness of Licensing Procedures for Exportation of Agricultural Commodities, Medicine, and Medical Devices to Sudan and Iran Office of Foreign Assets Control, Treasury. ACTION: Request for comments. AGENCY: SUMMARY: The Office of Foreign Assets Control (‘‘OFAC’’) of the U.S. E:\FR\FM\11DEP1.SGM 11DEP1

Agencies

[Federal Register Volume 71, Number 237 (Monday, December 11, 2006)]
[Proposed Rules]
[Pages 71499-71500]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: E6-20976]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2006-26285; Directorate Identifier 2006-CE-69-AD]
RIN 2120-AA64


Airworthiness Directives; Pacific Aerospace Corporation Ltd Model 
750XL Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the 
products listed above. This proposed AD results from mandatory 
continuing airworthiness information (MCAI) issued by an aviation 
authority of another country to identify and correct an unsafe 
condition on an aviation product. The MCAI describes the unsafe 
condition as possible undersize rivets in the fuselage roof at STN 
180.85, BL 19.67, WL 86.2. The proposed AD would require actions that 
are intended to address the unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by January 10, 
2007.

ADDRESSES: You may send comments by any of the following methods:
     DOT Docket Web Site: Go to https://dms.dot.gov and follow 
the instructions for sending your comments electronically.
     Fax: (202) 493-2251.
     Mail: Docket Management Facility, U.S. Department of 
Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, 
Washington, DC 20590-0001.
     Hand Delivery: Room PL-401 on the plaza level of the 
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
     Federal eRulemaking Portal: https://www.regulations.gov. 
Follow the instructions for submitting comments.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://
dms.dot.gov; or in person at the Docket Management Facility between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this proposed AD, the regulatory evaluation, any 
comments received, and other information. The street address for the 
Docket Office (telephone (800) 647-5227) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Karl Schletzbaum, Aerospace Engineer, 
FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, 
Missouri 64106; telephone: (816) 329-4146; fax: (816) 329-4090.

SUPPLEMENTARY INFORMATION:

Streamlined Issuance of AD

    The FAA is implementing a new process for streamlining the issuance 
of ADs related to MCAI. The streamlined process will allow us to adopt 
MCAI safety requirements in a more efficient manner and will reduce 
safety risks to the public. This process continues to follow all FAA AD 
issuance processes to meet legal, economic, Administrative Procedure 
Act, and Federal Register requirements. We also continue to meet our 
technical decision-making responsibilities to identify and correct 
unsafe conditions on U.S.-certificated products.
    This proposed AD references the MCAI and related service 
information that we considered in forming the engineering basis to 
correct the unsafe condition. The proposed AD contains text copied from 
the MCAI and for this reason might not follow our plain language 
principles.

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2006-
26285; Directorate Identifier 2006-CE-69-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to https://
dms.dot.gov, including any personal information you provide. We will 
also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The Civil Aviation Authority (CAA), which is the aviation authority 
for New Zealand, has issued CAA AD DCA/750XL/8, Drafted: May 9, 2006; 
Effective Date: August 31, 2006 (referred to after this as ``the 
MCAI''), to correct an unsafe condition for the specified products. The 
MCAI states the finding of the possible installation of undersize 
rivets in the fuselage roof at STN 180.85, BL 19.67, WL 86.2. The MCAI 
requires that you inspect the rivets in the fuselage roof at STN 
180.85, BL 19.67, WL 86.2, and replace undersize rivets. You may obtain 
further information by examining the MCAI in the AD docket.

Relevant Service Information

    Pacific Aerospace Corporation Ltd has issued PAC Pacific Aerospace 
Corporation Mandatory Service Bulletin PACSB/XL/019, Date Issued: April 
21, 2006. The actions described in this service information are 
intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of the Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with this State of Design Authority, they 
have notified us of the unsafe condition described in the MCAI and 
service information referenced above. We are proposing this AD because 
we evaluated all information and determined the unsafe condition exists 
and is likely to exist or develop on other products of the same type 
design.

Differences Between This Proposed AD and the MCAI or Service 
Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But

[[Page 71500]]

we might have found it necessary to use different words from those in 
the MCAI to ensure the AD is clear for U.S. operators and is 
enforceable. In making these changes, we do not intend to differ 
substantively from the information provided in the MCAI and related 
service information.
    We might also have proposed different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
described in a separate paragraph of the proposed AD. These 
requirements, if ultimately adopted, will take precedence over the 
actions copied from the MCAI.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 7 products of U.S. registry. We also estimate that 
it would take about 16 work-hours per product to comply with the 
proposed AD. The average labor rate is $80 per work-hour. Required 
parts would cost about $100 per product. Where the service information 
lists required parts costs that are covered under warranty, we have 
assumed that there will be no charge for these costs. As we do not 
control warranty coverage for affected parties, some parties may incur 
costs higher than estimated here. Based on these figures, we estimate 
the cost of the proposed AD on U.S. operators to be $9,660, or $1,380 
per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

Pacific Aerospace Corporation Ltd: Docket No. FAA-2006-26285; 
Directorate Identifier 2006-CE-69-AD.

Comments Due Date

    (a) We must receive comments by January 10, 2007.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Model 750XL airplanes, serial numbers 
102, 104 through 120, 122, and 125, certificated in any category.

Reason

    (d) The mandatory continuing airworthiness information (MCAI) 
states the finding of the possible installation of undersize rivets 
in the fuselage roof at STN 180.85, BL 19.67, WL 86.2.

Actions and Compliance

    (e) Unless already done, within the next 150 hours time-in-
service after the effective date of this AD, inspect the rivets in 
the fuselage roof at STN 180.85, BL 19.67, WL 86.2, and replace 
undersize rivets, following PAC Pacific Aerospace Corporation 
Mandatory Service Bulletin PACSB/XL/019, Date Issued: April 21, 
2006.

FAA AD Differences

    Note: This AD differs from the MCAI and/or service information 
as follows:
    No differences.

Other FAA AD Provisions

    (f) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Standards Staff, FAA, ATTN: Karl Schletzbaum, Aerospace Engineer, 
FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, 
Missouri 64106; telephone: (816) 329-4146; fax: (816) 329-4090, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act (44 
U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has 
approved the information collection requirements and has assigned 
OMB Control Number 2120-0056.

Related Information

    (g) Refer to MCAI Civil Aviation Authority AD DCA/750XL/8, 
Drafted: May 9, 2006; Effective Date: August 31, 2006; and PAC 
Pacific Aerospace Corporation Mandatory Service Bulletin PACSB/XL/
019, Date Issued: April 21, 2006, for related information.

    Issued in Kansas City, Missouri, on December 4, 2006.
John R. Colomy,
Acting Manager, Small Airplane Directorate, Aircraft Certification 
Service.
 [FR Doc. E6-20976 Filed 12-8-06; 8:45 am]
BILLING CODE 4910-13-P