Federal Aviation Administration January 25, 2012 – Federal Register Recent Federal Regulation Documents

Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2012-838
Type: Rule
Date: 2012-01-25
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Model 767-200 and 767-300 series airplanes. This AD was prompted by reports of water accumulation in the forward lower lobe of the forward cargo compartment. This AD requires installing cargo bulkhead supports, ceiling supports, a secondary dam support, drainage tubing, and ceiling panels to the forward lower lobe in the forward cargo compartment. We are issuing this AD to prevent water from accumulating in the forward lower lobe of the forward cargo compartment and entering the adjacent electronic equipment bay, which could result in an electrical short and the potential loss of several functions essential for safe flight.
Revision of Compulsory Reporting Points; Alaska
Document Number: 2012-1394
Type: Rule
Date: 2012-01-25
Agency: Federal Aviation Administration, Department of Transportation
This action revises the published description of two low altitude Alaskan compulsory reporting points; one in the vicinity of Homer and the other in the vicinity of Kenai. Specifically, the FAA is revising the description of CLAMS and SKILA to address recent technical adjustments to their actual locations.
Airworthiness Directives; 328 Support Services GmbH Airplanes
Document Number: 2012-1126
Type: Rule
Date: 2012-01-25
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all 328 Support Services GmbH (Type Certificate previously held by AvCraft Aerospace GmbH; Fairchild Dornier GmbH; Dornier Luftfahrt GmbH) Model 328-100 and 328-300 airplanes. This AD was prompted by a manufacturer safety analyses review on flight control which resulted in recommendations for reduced repetitive inspection intervals for the flight controls certification maintenance requirements (CMR) of the tab-to-actuator linkage. This AD requires revising the airplane maintenance program by incorporating certain CMR tasks. We are issuing this AD to prevent failure of these components or their constituent parts which could lead to reduced control of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2012-1125
Type: Rule
Date: 2012-01-25
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 757-200, -200CB, and -300 series airplanes with off-wing escape slide systems installed. This AD was prompted by reports of in-flight loss of the off-wing escape slide. This AD requires modifying the door latch fittings and witness mark placards of the off-wing escape slide systems; and for certain airplanes, replacing the bearings and lockbase retainer in the door latch assembly, relocating and adjusting the sensor target and the sensor proximity switch, and testing to ensure positive door locking and corrective action if necessary. For certain airplanes, this AD would also require installing a bumper assembly and placards. We are issuing this AD to prevent the in-flight loss of the off-wing escape slide, which could result in the unavailability of the escape slide during an emergency evacuation. Additionally, the departed slide could cause damage to the fuselage, wing, flaps, or stabilizer, which could degrade flight control.
Airworthiness Directives; Cirrus Design Corporation Airplanes
Document Number: 2012-1122
Type: Rule
Date: 2012-01-25
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Cirrus Design Corporation (Cirrus) Model SR22T airplanes. This AD was prompted by reports of partial loss of engine power due to a dislodged rubber gasket/seal being ingested into the turbocharger. This AD requires inspection and modification of the air box flange welds and slots and installation of induction system air box seals as applicable. We are issuing this AD to correct the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.